AMP RESEARCH 86151-01A Powerstep Smartseries Running Board Installation Guide

INSTALLATION GUIDE

86151-01A Power step Smartseries Running Board

SMART SERIES APP: Download App to your phone and unlock the latest features including override, light controls, and diagnostics.

https://www.amp-research.com/powerstep-smart-series-running-board

INSTALLATION TIME
2-3 Hours
Professional installation recommended

SKILL LEVEL

1 2 3 4
4= Experienced

TOOLS REQUIRED

• Safety goggles
• 10 mm socket
• 13 mm socket
• 13 mm end wrench
• Ratchet wrench and extension
• Wire stripper
• 9/32” & 19/64” Drill Bit
• 3/16” hex key wrench ( allen wrench)
• 4mm hex key wrench ( allen wrench)
• Electrical tape
• Weather proof caulking (silicone sealer)

WARRANTY
5-Year Limited Warranty

AMP RESEARCH POWERSTEP SMART SERIES TM – FORD F-150
INSTALLATION GUIDE
Attaching motor to linkage assembly
The motors must be attached to the linkage assemblies before continuing the installation process.

CAUTION: HANDLE WITH CARE.
To insure our customers receive all components with full integrity, we pack the motors separate from their linkage assemblies. This requires that the installer position and fasten the motor before continuing with the install. Please follow the instructions below and handle the assembly carefully.
CAUTION: Dropping the assembly or any excessive impact MAY cause damage to the motor.
Instructions:

1. Position the gear cover in place as shown if not already in place.
2. Seat motor into position on the three mounting bosses. This may require an adjustment of the gear by moving the swing arms.
3. After seating into place, fasten the motor with the three motor mount screws with 4mm allen wrench. Tighten screws to 36 in-lbs (4N-m). Do not over torque.

PARTS LIST AND HARDWARE IDENTIFICATION

Note: Some Applications require modification.

(A) End cap left (x1)
(B) End cap right (x1)
(C) T-nut insert (x2)
(D) (S) Style clips (x2)

Locate mounting points; first and last set of studs on the inner sill.
Motor Linkage mounts toward the front of the truck and Idler mount toward the rear.
Driver side shown below.Mount drive and Idler linkage assemblies. Repeat for passenger side. Make sure linkages sit square, fully resting on studs before tightening. Torque to 16 ft. lbs (22N·m)

Relocate Brake Cable Guide as shown in following steps.

Remove fuses from wire harness. Connect red power lead to battery. Connect black ground lead to 13mm bolt outside of fencer wall. Route shorter leg of harness down passenger-side wheel well and longer leg of harness down along driver side wheel well. Secure with tie wraps (15).

Attach wire harness (4) to controller (5) (make sure connector locking tabs fully engage). Mount controller with the two 11” tie wraps (16) to factory conduit, just forward of battery.
Route factory harness underneath vehicle and plug in motors (both sides). Route remaining LED light wires back towards rear of vehicle.

Remove driver side front kick panel and door sill plate. Roll back carpet to access hole for passing trigger wire into cab of vehicle.

On Super crew models, remove grommet in floor panel above front linkage on driver side.
Poke small hole into grommet and thread the trigger wire through and up into the cabin of vehicle.
Seal grommet with silicone sealer.

On Super Cab models , use a 9/32” drill bit to drill hole through floor and insert grommet (#9) that is supplied with kit.
Thread the wire through and apply silicone sealant.

OBD II install: Use Supplied Posi-Lock™ (6) connector to attach the Plug and Play Module to the Harness. Attach yellow wire on the harness to the yellow wire on the module. Plug in module to OBD II port on the vehicle. Secure harness with supplied tie wraps.

Wire OBD II connector with Posi-Lock™.

Attach step, sliding the mounting T-nut into position. Torque to 10 ft lbs (13.5 Nm)

On each side of the vehicle measure from the rear linkage to end of the board. Measurement should be approximately 11” as shown below.

On each side of the vehicle use tape to mark the led drill location two sections from studs as shown below. Use tape to indicate. Locations are approximately 22” & 66” from front door edge.

Mark hole location 1/2” midpoint of the rocker with tape and center punch and drill 19/64” hole into pinch weld. Deburr hole and insert grommet (#13) for LED Wire.

Route LED wires though through grommet, clean surface, and stick on to rocker panel as shown below.

Using supplied butt connectors, connect the lamp wires. Red to Red, Black to Black. Heat the shrink tubing on the connecters to seal wires. Close and wrap with conduit and electrical tape. Secure all loose wires with cable ties with lamp wires pulled upward to avoid any wire snagging.

FINAL SYSTEM CHECK

Check that all doors activate the Power Step and the LED lights work when doors open and close.
NORMAL OPERATION: When the doors open, Power Step automatically deploys from under the vehicle.
When the doors are closed, Power Step will automatically return to the stowed/retracted position. Note that there is a 2-second delay before the Power Step returns to the stowed/retracted position.
CORRECT OPERATION OF LIGHTS: All four lamps will illuminate upon opening any door of vehicle. Lamps will stay on until restowing of both Power Steps or until 5 minutes has expired with the doors open. When the lights timeout after 5 minutes, they can be reillumintated by closing and opening any door of vehicle.

Download our Smart Series App on your Android phone or iPhone by scanning the QR code below and follow the instructions. Or visit your app store and search “AMP Research Power step” to download app.

https://www.amp-research.com/powerstep-smart-series-running-board

AMERICAN DESIGNED, ENGINEERED AND MANUFACTURED.

Thank you for your recent AMP Research Purchase.
REGISTER YOUR PRODUCT TODAY FOR FASTER SERVICE & PRODUCT UPDATES
Please visit: www.amp-research.com/productregistration  or scan the QR Code

http://www.amp-research.com/productregistration

Product Registration Benefits:

• Ensure we have your purchase receipt and product info in our system which is required for warranty
• Faster and easier access to customer service and tech support in the unlikely event you need warranty or product support
• Registration helps us keep you up to date on product information and offers To view other Amp Research products that may be offered for your vehicle. Please visit: www.amp-research.com

Congratulations on your purchase of the genuine AMP Research Power Step!
Here’s what you should know…

POWER-DEPLOYABLE RUNNING BOARDS OPERATION:
AMP Research Power Step running boards automatically move when the doors are opened to assist entering and exiting the vehicle.
Automatic power deploy:
The running boards will extend down and out when the doors are opened.
Automatic power stow:
The running boards will return to the stowed position when the doors are closed. There will be a 2-second delay before the running boards move to the stowed position.

Automatic stop:
If an object is in the way of the moving running board, the running board will automatically stop. To reset, clear any obstruction, then simply open and close the door to resume normal operation.
Manually set in the deployed (OUT) position for access to the roof:
The running boards can be manually set in the deployed position by firmly holding the step down with your foot while at the same time closing the door. To resume normal operation, open and close the door.

Maintenance: In adverse conditions, debris such as mud, dirt, and salt may become trapped in the running board mechanism, possibly leading to unwanted noise. If this occurs, manually set the running boards to the deployed position  and flush the front and rear hinge arms with a high-pressure car wash wand. Avoid spraying the motors directly. After washing, apply silicone spray lubricant to the hinge pivot pins. Do not apply silicone, wax or protectants like Armor  All® to the running board stepping surface. Caution! Keep hands away when the running board is in motion.

5-YEAR LIMITED WARRANTY

AMP RESEARCH warrants this product to be free from defects in material and workmanship for FIVE (5) YEARS FROM DATE OF PURCHASE, provided there has been normal use and proper maintenance. This warranty applies to the original purchaser only. All remedies under this warranty are limited to the repair replacement of the product itself, or the repair or replacement of any component part thereof, found by the factory to be defective within the time period specified. The decision to repair or replace is wholly within the discretion of the manufacturer.
This warranty specifically excludes labor. If you have a warranty claim, first you must call our factory at the number below for instructions. You must retain proof of purchase and submit a copy with any items returned for warranty work.  Upon completion of warranty work, if any, we will return the repaired or replaced item or items to you freight prepaid. Damage to our products caused by accidents, re, vandalism, negligence, misinstallation, misuse, Acts of God, or by  defective parts not manufactured by us, is not covered under this warranty.
ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR PURPOSE CREATED HEREBY ARE LIMITED IN DURATION TO THE SAME DURATION AND SCOPE AS THE EXPRESS WRITTEN  WARRANTY. OUR COMPANY SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGE.
Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.
FOR WARRANTY ISSUES WITH THIS PRODUCT PLEASE CALL AMP RESEARCH TECH SUPPORT 1-888-983-2204
WARNING
Be sure to read and precisely follow the provided instructions when installing this product. Failure to do so could place the vehicle occupants in a potentially dangerous situation. After installing or reinstalling, re-check to insure that the product is properly installed.

The material that your product is made from can be recycled.
Please also consider recycling the packaging that your product came in.

References

• AMP Research Accessories | RealTruck
• RealTruck Warranty Registration | RealTruck

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>