AMP RESEARCH 86139-01A Power Step Smart Series Running Boards Installation Guide
- June 13, 2024
- AMP RESEARCH
Table of Contents
AMP RESEARCH 86139-01A Power Step Smart Series Running Boards
INSTALLATION TIME
3-5 Hours Professional installation recommended
SKILL LEVEL
TOOLS REQUIRED
- Safety goggles
- Measuring tape
- 13mm wrench
- 19mm wrench
- 13mm socket
- 10mm socket
- Ratchet wrench and extension
- Wire stripper / cutter
- 3/16” hex key ( allen wrench )
- 4mm hex key ( allen wrench )
- Rivet Tool
- 1/8”, 9/32” and 3/16” Drill Bit
- T27 torx Bit
- Center Punch
- Anti Corrosion Paint
- Electrical tape
WARRANTY
5-Year Limited Warranty
SMART SERIES APP:
Download App to your phone and unlock the latest features including override,
light controls, and diagnostic.
INSTALLATION GUIDE
Motor to linkage assembly
NOTE: The motors will be attached on step 29 (page 13).
EXPLODED VIEW
- Motor
- Socket cap screw
- Washer
- Drive Gear Housing Cover
CAUTION: HANDLE WITH CARE.
To ensure our customers receive all components with full integrity, we pack
the motors separate from their linkage
assemblies. This requires that the installer position and fasten the motor
before continuing with the install. Please follow the instructions below and
handle the assembly carefully.
CAUTION : Dropping the assembly or any excessive impact MAY cause damage
to the motor.
Instructions:
- Position the gear cover in place as shown if not already in place.
- Seat motor into position on the three mounting bosses. This may require an adjustment of the gear by moving the swing arms.
- After seating into place, fasten the motor with the three motor mount screws with 4mm Hex Head. Tighten screws to 36 in-lbs (4N-m). Do not over torque.
PARTS LIST AND HARDWARE IDENTIFICATION
Note: Some Applications require modification
Application Cut Length
Crew Cab, Mega Cab 79” (No Modification Required)
Quad Cab 72” (Trim 7”)
Regular Cab 50” (Trim 29”)
( A ) End cap left (x1)
( B ) End cap right (x1)
( C ) T-nut insert (x2)
( D ) (S) Style clips (x2)
Driver Side Linkages
Passenger Side Linkages
Hard ware
Parts
FOR 1500 MODELS ONLY!
Package content
NOTE : 1500 RAM Only! Power step installations require additional steps and come with the required additional hardware. Please read and carefully follow the instructions. Follow Steps 1-5 to relocate brake cable and wire harness plug and then proceed with the Power Step installation. For Ram 2500/3500 skip to step 6.
On Drivers side of vehicle towards front of body remove harness bracket with 10mm socket or wrench. Remove plug from bracket. And replace with supplied bracket using two of the three factory screws.
While holding brake cable adjustment nut with wrench (located on driver side along frame, towards the rear), loosen brake cable to allow for slack. Mark position of nut before loosening.
After gaining enough slack, detach brake cable as shown below. This detachment point is located just to the rear of the adjustment nut.
Remove brake cable guide from frame by depressing locking tabs and sliding guide out through hole. Unthread brake cable from frame mount
Attach brake cable guide to supplied Brake Cable Bracket (28) and mount bracket with supplied hardware. Reattach brake cable and readjust brake cable adjustment nut to original position.
HARDWARE MOUNTING OVERVIEW (passenger side shown)
Locate forward most and rearward most mounting provisions on inner sill of
truck.
Remove tape from sill drain hole at both mounting points.
Note: Some vehicles may have Front welded fasteners installed already.
Backing plates and rivet nuts are not needed on these locations. Factory Rivet
nuts will need to be removed to install backing plates.
Set Reinforcement Plate in place and locate with rivet nuts. Drill hole using an 1/8” drill bit. After drilling apply paint to prevent rusting.
Once hole is drilled insert a piece of string or wire through hole in
Reinforcement Plate.
Set plate into position.
Set rivet nuts into place for alignment. Insert pop rivet through hole in
plate and secure in place. Once pop rivet is installed remove string or wire
from Reinforcement Plate.
NOTE: Verify plate is pulled flush to the body before securing pop rivet.
Assemble Hex Bolt (lubricated with soapy water), Washer, Rivet Tool, and Rivet Nut together as shown and place into hex cutouts in sill. An extra Hex Bolt and M8 Washer is supplied to install rivet nuts.
With Rivet Nut Tool held in place with 19mm wrench, tighten Hex Bolt until
Rivet Nut deforms and secures itself to the sheet metal (110 in-Lbs. or 4
turns).
Remove Hex Bolt and Rivet Nut Tool.
Repeat for each of the four mentioned mounting locations.
NOTE : Hold Rivet tool with wrench while loosening
WARNING : Rivet Nuts not properly collapsed will not hold securely to
sheet metal.
Once rivet nuts are in place use a screwdriver to push back tab in hole to avoid interference with linkage mount.
Linkage Installation : On rear linkages thread front hex bolt into rivet nut with washer. Note on Front drive linkages both hex bolts can be threaded into position.
Rear Linkage : With linkage in position insert Hex bolts into rivet nut locations. Snug bolts but do not tighten. Note: Pre threaded bolt will attach to slot centered on linkage. Idler linkages will use 2 of the 3 mount points.
Front Linkage: On Vehicles that have crash bracket remove bolts attaching bracket to inner sill of truck. Thread hex bolts into position as in step 13.
If crash bracket is not present use supplied spacer in place of bracket. Spacer can be inserted after linkage is up into position. Spacer will be held in place by drilling and pop riveting into place. Rivets will be installed in step39&40.
All Linkages : Slide linkage over pre threaded bolts. Using a T27 Torx driver start torx bolts and washers. Snug bolts but do not tighten. Replace bolts from step 15 if present. 16
Using a 13mm wrench tighten two hex bolts on linkage. Torque to 16 ft-lbs. Torque bolts from step 15 if present to 50 Flt.Lts..
Using a T27 Torx driver torque bolts to 6 ft-lbs
The jogs in the lower part of the linkages point toward one another, as shown,
Drive (motor) Linkage in the Front and Idler Linkage in the Rear.
Note: Linkage position described in parts list on page 3.
Install boards : Slide mounting T-Nut of board into position and attach to linkages. Shift board forward as much as possible for proper clearance. The end of board/end cap will nest into linkage lower mount 1/2” when positioned correctly. With boards in extended position step on boards to seat linkages. Walk the length of the board taking bouncing steps. DO NOT JUMP ON BOARD! Verify that board end caps do not contact the pinch weld. If Endcaps make contact loosen 4 button head screws at pinch weld. Walk the length of the board and apply weight to the center of the board and while applying weight retighten button head screws at pinch weld.
For instructions on how to adjust board due to pinchweld Interference, scan QR Code to watch video, or type the following link to your browser: https://youtu.be/ITbAeixVKdQ
Prepare large tie-wraps (13) for mounting Power Step Controller. Loosely loop tie-wraps around large bundle of wires behind battery in engine.
Insert controller (5) into tie-wrap (13) loops and cinch down securely. The tie-wraps should cinch down into channels on controller surface.
Remove fuses from Power Step Wire Harness.
Connect power leads from Controller, Red to positive battery terminal and Black to the vehicle body ground as shown.
Locate large rubber wire boot on driver side firewall as shown below. Slice small opening as shown below to run trigger wires through.
Tape leading end of wires together and push through rubber boot to cabin side of the firewall. Silicon lubricant may be used for ease of passage. The trigger wires will come out just above and to the left of the brake pedal.
OBD II install : Use Supplied Posi-Lock™ (14) connectors to attach the Plug and Play Module to the Harness. Attach matching colors on the harness to the wires on the module. Plug in module to OBD II port on the vehicle. Secure harness with supplied tie wraps. Note: If the OBD II pass thru harness (76404-01A) was purchased see install sheet supplied in packaging. The pass through harness allows for an open port for other accessories. See below for a brief description.
Route the two Wire Harness (4) legs down over the wheel wells toward Motor Linkages, long leg across to the passenger side. Secure harness with cable ties (12).
Using a 4mm hex key torque bolts to 36 in-lbs. See page 2 for motor installation instructions.
On driver side, run Wire Harness leg down and along underside of the vehicle floor and frame to front Drive Linkage. Connect harness to motor and secure harness with tie wraps. Route remainder of wire harness towards rear linkage assembly for LED lights
On Passenger Side, run Wire Harness leg down and along underside of the vehicle floor and frame to front Drive Linkage. Connect harness to motor and secure harness with tie wraps. Route remainder of wire harness towards rear linkage assembly for LED lights.
On each side of the vehicle measure from the front edge of door line on the
pinch weld to the specified lengths below.
Measure at 22” for the front LED Light and 64-3/4” for the rear LED Light.
Note for Quad cabs mount lights at 22” and 54” for Regular cabs mount lights at 10” and 45”.
Drill a 9/32” hole through the pinch weld at marked locations. Debur all holes. After drilling apply paint to holes to prevent rusting
Insert grommet (17) into drilled holes. Insert lamp wires through the grommets. (Silicon lube will help wires slip through grommets.)
Affix lamp (18) to rocker panel surface. Make sure lamp is affixed to a flat, clean surface.
Using supplied butt connectors (19), connect the lamp wires. Red to Red, Black to Black. Once Crimped use heat gun to shrink tube.
Close and wrap with conduit and electrical tape. Secure all loose wires with cable ties, with lamp wires pulled upward to avoid any wire snagging.
With linkage resting square on the hex bolts Using a 3/16” Drill bit, drill both upper holes in linkage through Sheetmetal. After drilling apply paint to holes to prevent rusting.
Using a Rivet Gun install rivets.
Reinstall fuses to Power step harness. Check that all doors activate the Power
Step and the LED
Lights work when doors open and close. Reinstall any remaining trim panels.
FINAL SYSTEM CHECK
Check that all doors activate the Power Step and the LED lights work when
doors open and close. NORMAL OPERATION: When the doors open, Power Step
automatically deploys from under the vehicle. When the doors are closed, Power
Step will automatically return to the stowed/retracted position. Note that
there is a 2-second delay before the Power Step returns to the
stowed/retracted position.
CORRECT OPERATION OF LIGHTS: All four lamps will illuminate upon opening any
door of vehicle.
Lamps will stay on until restoring of both Power Steps or until 5 minutes has
expired with the doors open.
When the lights timeout after 5 minutes, they can be reillumintated by closing
and opening any door of vehicle.
CUSTOMER SUPPORT
AMP RESEARCH TECH SUPPORT 1-888-983-2204 (Press 2) Monday – Friday, 7:00 AM – 5:00 PM PST
Invented, engineered and manufactured exclusively by AMP Research in the USA. May be covered by one OR MORE of the following patents: 6,641,158; 6,830,257; 6,834,875; 6,938,909; 7,055,839; 7,380,807; 7,413,204; 7,398,985; 7,584,975; 7,566,064; 7,487,986; 8,157,277; 8,408,571; 9,302,626; 9,561,751; 10,053,017; CA2463717 ©2012 AMP Research. All rights reserved. Printed in USA.
Thank you for your recent AMP Research Purchase.
REGISTER YOUR PRODUCT TODAY FOR FASTER SERVICE & PRODUCT UPDATES
Please visit:
www.amp-research.com/productregistration or scan the QR Code
Product Registration Benefits:
- Ensure we have your purchase receipt and product info in our system which is required for warranty
- Faster and easier access to customer service and tech support in the unlikely event you need warranty or product support
- Registration helps us keep you up to date on product information and offers
To view other Amp Research products that may be offered for your vehicle.
Please visit: www.amp-research.com
POWER-DEPLOYABLE RUNNING BOARDS OPERATION:
AMP Research Power Step running boards automatically move when the doors
are opened to assist entering and exiting the vehicle.
Automatic power deploy:
The running boards will extend down and out when the doors are opened.
Automatic power stow:
The running boards will return to the stowed position when the doors are
closed. There will be a 2-second delay before the running boards move to the
stowed position.
Automatic stop:
If an object is in the way of the moving running board, the running board will
automatically stop.
To reset, clear any obstruction, then simply open and close the door to resume
normal operation.
Manually set in the deployed (OUTI position for access to the roof:
The running boards can be manually set in the deployed position by firmly
holding the step down with your foot while at the same time closing the door.
To resume normal operation, open and close the door.
Maintenance: In adverse conditions, debris such as mud, dirt, and salt
may become t rapped In the running board mechanism, possibly leading to
unwanted noise. If this occurs, manually set the running boards to the
deployed position and flush the front and rear hinge arms with a high-pressure
car wash wand.
Ayad spying the motors directly After washing, apply silicone spray lubricant
to the hinge pivot pins. Do not apply silicone, wax or protectants like Armor
All” to the running board stepping surface.
5-YEAR LIMITED WARRANTY
AMP RESEARCH warrants this product to be free from defects in material and
workmanship for FIVE (5) YEARS FROM DATE OF PURCHASE, provided there has been
normal use and proper maintenance. This warranty applies to the original
purchaser only. All remedies under this warranty are limited to the repair
replacement of the product itself, or the repair or replacement of any
component part thereof, found by the factory to be defective within the time
period specified. The decision to repair or replace is wholly within the
discretion of the manufacturer.
This warranty specifically excludes labor. If you have a warranty claim, first
you must call our factory at the number below for instructions. You must
retain proof of purchase and submit a copy with any items returned for
warranty work. Upon completion of warranty work, if any, we will return the
repaired or replaced item or items to you freight prepaid. Damage to our
products caused by accidents, fire, vandalism, negligence, misinstallation,
misuse, Acts of God, or by defective parts not manufactured by us, is not
covered under this warranty.
ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR
PURPOSE CREATED HEREBY ARE LIMITED IN DURATION TO THE SAME DURATION AND SCOPE
AS THE EXPRESS WRITTEN WARRANTY. OUR COMPANY SHALL NOT BE LIABLE FOR ANY
INCIDENTAL OR CONSEQUENTIAL DAMAGE.
Some states do not allow limitations on how long an implied warranty lasts, or
the exclusion or limitation of incidental or consequential damages, so the
above limitations or exclusions may not apply to you. This warranty gives you
specific legal rights, and you may also have other rights that vary from state
to state.
FOR WARRANTY ISSUES WITH THIS PRODUCT PLEASE CALL AMP RESEARCH TECH SUPPORT
1-888-983-2204
Be sure to read and precisely follow the provided instructions when installing this product. Failure to do so could place the vehicle occupantsinapotentiallydangeroussituation.Afterinstallingorreinstalling,re- check to insure that the productids properly installed.
The material that your product is made from can be recycled. Please also consider recycling the packaging that your product came in.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>