AMP RESEARCH 75422-01A AMP PowerStep Instruction Manual
- June 13, 2024
- AMP RESEARCH
Table of Contents
AMP RESEARCH 75422-01A AMP PowerStep
Product Information
Product: AMP Part# 75422-01A
Application: Ford Super Duty – 2023 (Driver Side only) F-250/350 (Fits
all Beds/Cabs)
Manufacturer: AMP Research
Manufacturer Contact: AMP RESEARCH TECH SUPPORT
1-888-983-2204 (Press 2) Monday –
Friday, 7:00 AM – 5:00 PM PST
Manufacturer Website: www.amp-research.com
Product Usage Instructions
- Locate the access hole at the bottom of the stock step assembly.
- Using a screwdriver or similar tool, push up through the hole while pulling the top of the step pad out.
- Remove the bottom part of the step pad by using a ratchet to remove both bolts holding it in place.
- Insert the reinforcement nut plate into position beside the step sub-frame, on top of the lower shelf of the sub-frame and between the side supports.
- Re-install the step pad, starting with the bottom portion and torque the bolts on the bottom part of the step pad.
- Install the top part of the step pad, ensuring it snaps back in place.
- Fasten the Linkage Assembly to the side step sub-frame with two medium M8 bolts, threading them into the reinforcement nut plate. Do not torque yet, allowing linkage some adjustment for subsequent steps.
- Position the lateral support bracket and fasten as shown, using long fasteners at the frame mount and medium length fasteners at the linkage. Use the shown spacer only for long bed trucks (8 foot). Do not torque.
- To deploy the step, press down using your foot on the outside edge of the step pad.
- To retract the step, gently kick up on the underside of the step pad.
For any further assistance or product updates, please register your product at www.amp-research.com/productregistration.
Locate access hole at bottom of stock step assembly (see figure a.). Using a screwdriver or similar, push up through the hole while pulling top of step pad out (see figure b.).
Insert reinforcement nut plate into position onto beside step sub-frame. The final position will be on top of lower shelf of the sub-frame and between the side supports.
Next, install top part of step pad, make sure it snaps back in place.
To deploy the step, press down using your foot on the outside edge of the step pad.
To retract, gently kick up on the underside of the step pad.
Thank you for your recent AMP Research Purchase.
REGISTER YOUR PRODUCT TODAY FOR FASTER SERVICE & PRODUCT UPDATES
Please visit:
www.amp-research.com/productregistration or scan the QR Code
Product Registration Benefits
- Ensure we have your purchase receipt and product info in our system which is required for warranty
- Faster and easier access to customer service and tech support in the unlikely event you need warranty or product support
- Registration helps us keep you up to date on product information and offers
To view other Amp Research products that may be offered for your vehicle.
Please visit: www.amp-research.com
-
BEDSTEP2™ OPERATION
The AMP Research BedStep2™ is foot operated and deploys and retracts with a nudge of your foot. To deploy, press down using your foot, on the outside edge of the step pad. Maximum load capacityof the deployed step pad is 300 lbs. Always use appropriate hand holds when stepping up to or down from your truck’s cargo bed. -
To retract, gently kick up on the underside of the step pad.
-
MAINTENANCE TIPS: The stepping surface and linkage should be periodically washed with mild soap and water using a soft brush or sponge to dislodge any mud, dirt or accumulated road grime. In severe driving conditions, pressure washing the linkage is strongly recommended. Do not apply silicone spray, waxes or protectants like Armor All” to the stepping surfaces.
CAUTION: BEDSTEP2™ SHOULD ALWAYS BE STOWED IN THE RETRACTED POSITION WHEN DRIVING.
AMP RESEARCH LIMITED WARRANTY
AMP RESEARCH warrants this product to be free from defects in material and
workmanship for THREE (3) YEARS FROM DATE OF PURCHASE, provided there has been
normal use and proper maintenance. This warranty applies to the original
purchaser only. All remedies under this warranty are limited to the repair
replacement of the product itself, or the repair or replacement of any
component part thereof, found by the factory to be defective within the time
period specified. The decision to repair or replace is wholly within the
discretion of the manufacturer. This warranty specifically excludes labor. If
you have a warranty claim, first you must call our factory at the number below
for instructions. You must retain proof of purchase and submit a copy with any
items returned for warranty work. Upon completion of warranty work, if any, we
will return the repaired or replaced item or items to you freight prepaid.
Damage to our products caused by accidents, fire, vandalism, negligence,
misinstallation, misuse, Acts of God, or by defective parts not manufactured
by us, is not covered under this warranty.
ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR
PURPOSE CREATED HEREBY ARE LIMITED IN DURATION TO THE SAME DURATION AND SCOPE
AS THE EXPRESS WRITTEN WARRANTY. OUR COMPANY SHALL NOT BE LIABLE FOR ANY
INCIDENTAL OR CONSEQUENTIAL DAMAGE.
Some states do not allow limitations on how long an implied warranty lasts, or
the exclusion or limitation of incidental or consequential damages, so the
above limitations or exclusions may not apply to you. This warranty gives you
specific legal rights, and you may also have other rights that vary from state
to state.
FOR WARRANTY ISSUES WITH THIS PRODUCT PLEASE CALL AMP RESEARCH CUSTOMER
SERVICE 1-888-983-2204
WARNING
Be sure to read and precisely follow the provided instructions when installing
this product. Failure to do so could place the vehicle occupants in a
potentially dangerous situation. After installing or reinstalling, re-check to
insure that the product is properly installed.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>