FEIT Electric CHD225CCTNLBK LED Decorative 5 Light Chandelier Instruction Manual

Model: CHD225CCTNLBK
22 INCH DECORATIVE 3-LIGHT CHANDELIER
IMPORTANT SAFETY INSTRUCTIONS
AND INSTALLATION GUIDE READ BEFORE INSTALLATION
SAVE THESE INSTRUCTIONS

We appreciate the trust and confidence you have placed in Feit Electric through the purchase of this product. We strive to continually create quality products designed to enhance your home. Visit us online to see our full line of products available for your home improvement needs. Thank you for choosing Feit Electric.

Safety Information

For your safety, always remember to:

• Turn off the power supply at the fuse or circuit breaker box before you install the fixture.
• Ground the fixture to avoid potential electric shock and to ensure reliable starting.
• Double-check all connections to be sure they are tight and correct.
• Wear rubber soled shoes and work on a sturdy wooden ladder.
• Account for small parts and discard packing material, as these may be hazardous to children.
  This fixture is designed for use in a circuit protected by a fuse or circuit breaker. It is also designed to be installed in accordance with local electrical codes. If you are unsure about your wiring, check your local electrical code or consult a qualified electrician.
  MIN 90° C SUPPLY CONDUCTORS

CAUTION: Turn off the main power at the circuit A breaker before installing the fixture, in order to prevent possible shock.
CAUTION: Consult a certified electrician to ensure correct branch circuit conductor.
WARNING: RISK OF SHOCK. House electric current can cause painful shock or serious injury unless handled properly.
CAUTION: RISK OF FIRE. Before installing your lighting fixture, thoroughly review this installation manual. If you do not have sufficient electrical wiring experience have your fixture installed by a certified electrician. All electrical connections must be in accordance with Local and National Electrical Code (NEC) Standards. Reliable operating temperature is O°F ~120°F. Suitable for Damp Locations. For more information including dimmer compatibility visit www.feit.com.
NOTICE: All electrical connections must be in accordance with local and National Electrical Code (N.E.C.) standards. If you are unfamiliar with proper electrical wiring connections obtain the services of a certified electrician.
Remove the fixture and the mounting package from the box and make sure that no parts are missing by referencing the illustrations on the installation instructions.

FCC STATEMENT

Supplier’s Declaration of Conformity:
47 CFR § 2.1077 Compliance Information Responsible Party: Feit Electric Company 4901 Gregg Road, Pico Rivera, CA 90660, USA Unique Identifier: CHD225CCTNLBK This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmul interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no quarantee that interference will not occur in a particular installation. I this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient o relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment. CAN ICES-005 (B).

Limited Warranty

This product is warrantied to be free from defects in workmanship and materials for up to 1 year from date of purchase.
If it fails to do so, please contact the Customer Service Team at www.feit.com.

Pre-Assembly

TOOLS REQUIRED

HARDWARE INCLUDED

NOTE: Hardware not shown to actual size.

Installation

1. Turning Off the Power Turn the power OFF at the switch and fusebox or the circuit breaker and place the wall switch in the off position.

2. Identifying the Wires black – line voltage white – neutral bare copper – ground
   

3. Removing the Mounting Plate Remove the mounting plate (FF) from the canopy BB by unscrewing the 4 mounting plate screws (Il) using a Phillips head screwdriver.

4. Assembling the Fixture
   • Assemble one side at a time.
   • Screw in the hollow bolt (KK) to one end of the 18-inch stem (EE).
   • Slide the thread adapter (LL) over the other end of the 18-inch stem (EE) with the threads of the thread adapter (LL) towards the hollow bolt (KK). DO NOT screw on the thread adapter (LL) to the fixture (AA) yet.
   • Position the 18-inch stem (EE) with the hollow bolt (KK) towards the fixture (AA).
   • Run the fixture (AA) wires through the 18-inch stem (EE).
   • Position the 12-inch stem (DD) with the pre-attached thread coupling (MM) end towards the 18-inch stem (EE).
   • Run the fixture (AA) wires through the 12-inch stem (DD).
   • Screw in the 12-inch stem (DD) to the other end of the 18-inch stem (EE).
   • Position the 6-inch stem (CC) with the pre-attached thread coupling (MM) end towards the 12-inch stem (DD).
   • Run the fixture (AF) wires through the 6-inch stem (CC).
   • Screw in the 6-inch stem (CC) to the other end of the 12-inch stem (DD).
   • Run the fixture (AA) wires at the end of the 6-inch stem (CC) through the canopy (BB).
   • Screw in the 6-inch stem (CC) to the canopy (BB).
   • Repeat the above steps to assemble the other side.
   • Screw on the thread adapters (LL) to the fixture (AA) to secure the assembled stems (CC, DD, EE) to the fixture (AA). NOTE: Do not screw the thread adapter (LL) onto the fixture (AA) until both stems are assembled and attached to the Canopy (BB).

5. Installing the Mounting Plate to the Junction Box Line up the mounting plate (FF) with the mounting holes on the junction box. Use a Philips head screwdriver to screw the junction box mounting screws (JJ) through the mounting plate (FF) and to the junction box.

6. Connecting the Wires
   To ground the fixture (AA) connect the bare copper ground wire from the fixture (AA) to the ground wire (usually green) from the junction box. Use the wago connector (GG) to connect the white fixture (AA) wire to the white junction box wire and the black
   fixture (AA) wire to the black junction box wire. Once the electrical connections have been made to the supply wire, take the black, white, blue, red, green and yellow wires that were fed through the canopy (BB) and insert them into their matching-colored connectors. To insert the wire securely, take a Philips head screwdriver and press and hold down the tab while you insert the wire. Release the tab once the wire is fully inserted.

7. Installing the Fixture to the Mounting Plate Lift the fixture canopy (BB) over the mounting plate (FF), lining up the holes on the outside of the canopy (BB). Using a Philips head screwdriver, screw in the 4 mounting plate screws (1l) through the canopy (BB) and into the mounting plate (FF).

8. Screwing in the Bulbs (bulbs not included) Screw the light bulbs into the Fixture (AA) light sockets clockwise until they are secure (over tightening can damage both the fixture and lithing.

Operating the Fixture

1. Selecting Modes
   • Flip the wall switch ON after installation to enter Mode 1 (light bulb only).
   •  Flip the wall switch OFF and back ON in less than 5 seconds to enter Mode 2 (light bulb + LED down light).
   •  Flip the wall switch OFF and back ON again in less than 5 seconds to enter Mode 3 (up light only).
   NOTE: If the unit is turned off for more than 10 seconds, the mode will automatically revert to the default mode of Mode 1 (area light only).

2. Changing Color Settings
   • While in Mode 2 (light bulb + LED down light), push the selector button on the canopy (BB) to select the desired color temperature.
   Continue to push the button to cycle through the available white colors.
   SW = Soft White = 2700K
   BW = Bright White = 3000K
   NW = Neutral White = 3500K
   CW = Cool White = 4000K
   DL = Daylight = 5000K
   NOTE: The downlight will remain the same color unless the selector button on the canopy (BB) is pushed to cycle through the different white colors.

Need Help? Thank you for your purchase.
Questions, comments or feedback?
Wed love to hear from you.
Visitfeit.com/help for support or connect with us:
@FeitElectric
@FeitElectricinc
feitelectriclighting
Please contact feit.com/help for further assistance.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>