NETGEAR FVS114IS ProSafe VPN Firewall Installation Guide

NETGEAR FVS114IS ProSafe VPN Firewall

Start Here
Follow these instructions to set up your VPN firewall. You can also consult the Reference Manual on the NETGEAR Web site at http://kbserver.netgear.com.

Prepare to Install Your FVS114 VPN Firewall

For Cable Modem Service: When you perform the VPN firewall setup steps be sure to use the computer you used when you first set up your cable Internet connection. For DSL Service: You may need information such as the DSL login name/e-mail address and password in order to complete the VPN firewall setup.

First, Connect the FVS114

1. CONNECT THE CABLES BETWEEN THE FVS114, COMPUTER, AND MODEM

   • a. Turn off your computer.

   • b. Unplug and turn off the broadband modem.

   • c. Locate the Ethernet cable (Cable 1 in the diagram) that connects your modem and computer.
     

   • d. Disconnect the cable at the computer end only, point A in the diagram.

   • e. Securely insert the Ethernet cable from your modem (Cable 1 in the diagram) into the INTERNET port of the FVS114 as shown in point B of the diagram.
     

   • f. Securely insert the blue cable that came with your FVS114 (the Blue NETGEAR Cable in the diagram below) into a LOCAL port on the firewall such as LOCAL port 4 (point C in the diagram), and the other end into the Ethernet port of your computer (point D in the diagram).
     Your network cables are connected and you are ready to restart your network.

2. RESTART YOUR NETWORK IN THE CORRECT SEQUENCE
   Warning: Failure to restart your network in the correct sequence could prevent you from connecting to the Internet.

   • a. First, plug in the power cord to your broadband modem, turn it on, and wait two minutes.

   • b. Now, plug in the power cord to your FVS114, turn it on, and wait one minute.

   • c. Last, turn on your computer.
     Note: For DSL customers, if ISP-provided software logs you in to the Internet, do not run that software. You may need to go to the Internet Explorer Tools menu, Internet Options, Connections tab page where you can select “Never dial a connection.”
     

   • d. Check the FVS114 status lights to verify the following:

   • PWR: The PWR light should turn solid green. If it does not turn solid green, check the adapter or the power switch.

   • TEST: The TEST light goes on when the router is first turned on and then goes off. If after two minutes it is still on, see the Troubleshooting Tips in this guide.

   • INTERNET: The INTERNET port LINK/ACT light should be lit. If not, make sure the Ethernet cable is securely attached to the FVS114 Internet port and the modem. Also, make sure the modem is powered on.

   • LOCAL: A LOCAL LINK/ACT light should be lit. The 100 LED indicates your computer is communicating at 100 Mbps; off indicates 10 Mbps. If a LOCAL LINK/ACT light is not lit, check that the Ethernet cable from the computer to the firewall is securely attached at both ends, and that the computer is turned on.

Now, Configure the FVS114 for Internet Access

Use the Smart Wizard configuration assistant to configure the FVS114.

1. From the Ethernet-connected computer you just set up, open a browser such as Internet Explorer or Netscape® Navigator. With the FVS114 in its factory default state, your browser will display the NETGEAR Smart Wizard welcome page. Note: If you do not see this page, type http://www.routerlogin.net in the browser address bar and click Enter.
   Click OK to proceed.
   If you still cannot connect to the FVS114, verify your computer networking setup. Your computer should be set to obtain both IP and DNS server addresses automatically, which is usually so. For help with this, please see the Reference Manual or animated tutorials on the Resource CD.

2. Follow the Smart Wizard prompts to connect to the Internet.

3. Click Done on the Success screen and be sure to click OK at the prompt to close the screen and finish.
   Note: The configuration assistant only appears when the FVS114 is in its factory default state. After you configure the FVS114, it will not appear again. You can always connect to the router configuration menu to change its settings. To do so, open a browser and go to http://www.routerlogin.net. Then, when prompted, enter admin as the username and password for the password both in lowercase letters.

Advanced User Wizard Bypass

Technically advanced users who want to bypass the Smart Wizard configuration assistant can do so by logging on to the firewall at http://www.routerlogin.net/basicsetting.htm with the user name of admin and the password of password, both in lowercase letters.

Troubleshooting Tips

Here are some tips for correcting common problems you may encounter.
Be sure to restart your network in this sequence:

1. Turn off and unplug the modem, turn off the FVS114, and shut down the computer.
2. Plug in and turn on the modem, wait two minutes.
3. Turn on the FVS114 and wait one minute.
4. Turn on the computer.

Make sure the Ethernet cables are securely plugged in.

• The INTERNET LINK light on the FVS114 will be lit if the Ethernet cable to the FVS114 from the modem is plugged in securely and the modem and FVS114 are turned on.
• For each powered on computer connected to the FVS114 with a securely plugged in Ethernet cable, the corresponding FVS114 LOCAL port LINK light will be lit. The front and back of the FVS114 identifies the number of each LOCAL port.

Make sure the network settings of the computer are correct.

• Ethernet cable and wirelessly connected computers should be configured to obtain IP and DNS addresses automatically via DHCP whenever possible. For help with this, please see the animated tutorials or the Reference Manual Appendix C on the Resource CD.
• Some cable modem ISPs require you to use the MAC address of the computer registered on the account. If so, in the Router MAC Address section of the Basic Settings menu, select, “Use this Computer’s MAC Address.” The firewall will then capture and use the MAC address of the computer that you are now using. You must be using the computer that is registered with the ISP. Click Apply to save your settings. Restart the network in the correct sequence.

Use the FVS114 status lights to verify the correct operation.

If the FVS114 Power light does not turn solid green within two minutes of turning the firewall on, or if the Test light does not go off, reset the firewall as described in the Reference Manual on the Resource CD.

Technical Support

Thank you for selecting NETGEAR products. After completing the Smart Wizard configuration assistant, locate the serial number on the bottom label of your product and use it to register your product at
http://www.NETGEAR.com/register.

Registration on the website or over the phone is required before you can use our telephone support service. The phone numbers for worldwide regional customer support centers are on the Warranty and Support Information card that came with your product. Go to http://kbserver.netgear.com for product updates and Web support.

Trademark

©2005 by NETGEAR, Inc. All rights reserved. NETGEAR is a registered trademark of NETGEAR, Inc. in the United States and/or other countries. Other brand and product names are trademarks or registered trademarks of their respective holders. Information is subject to change without notice.

FAQs

What is the NETGEAR FVS114IS ProSafe VPN Firewall?

The NETGEAR FVS114IS ProSafe VPN Firewall is a network security device designed to protect your network from security threats and provide Virtual Private Network (VPN) functionality for secure remote access.

What are the key features of the FVS114IS VPN Firewall?

The FVS114IS VPN Firewall offers features such as firewall protection, VPN support for secure remote connections, content filtering, Intrusion Detection System (IDS), and Denial of Service (DoS) protection.

How many simultaneous VPN tunnels does the FVS114IS support?

The number of simultaneous VPN tunnels supported by the FVS114IS VPN Firewall can vary depending on the model and firmware version. It is typically designed to support a limited number of VPN connections, often ranging from 8 to 20 tunnels.

What types of VPN protocols does the FVS114IS support?

The FVS114IS VPN Firewall often supports VPN protocols such as IPSec (Internet Protocol Security) and PPTP (Point-to-Point Tunneling Protocol) for secure remote access and site-to-site connections.

Is the FVS114IS suitable for small businesses and home offices?

Yes, the FVS114IS ProSafe VPN Firewall is well-suited for small businesses and home offices, providing robust network security and remote access capabilities without the complexity of enterprise-grade solutions.

Can the FVS114IS be used as a router for internet connectivity?

The FVS114IS can function as a router and firewall for internet connectivity, allowing you to connect your local network to the internet while providing network security features.

Does the FVS114IS support Quality of Service (QoS) for managing network traffic?

Some models of the FVS114IS VPN Firewall include Quality of Service (QoS) features that enable you to prioritize and manage network traffic for specific applications or services.

How do I configure and manage the FVS114IS VPN Firewall?

You can configure and manage the FVS114IS VPN Firewall through a web-based user interface. Access the device's settings by connecting to it via a web browser and entering the appropriate IP address.

Is the FVS114IS firmware upgradable?

Yes, the firmware of the FVS114IS VPN Firewall is upgradable. It's recommended to keep the firmware up to date to ensure the latest security patches and features are available.

What security measures are in place to protect the FVS114IS itself?

The FVS114IS VPN Firewall typically includes security measures such as a stateful packet inspection (SPI) firewall, VPN encryption, content filtering, and intrusion detection to protect the device from external threats.

What is the warranty period for the FVS114IS ProSafe VPN Firewall?

The NETGEAR FVS114IS ProSafe VPN Firewall typically come with a Limited Lifetime Warranty from the date of the purchase.

Where can I purchase the NETGEAR FVS114IS ProSafe VPN Firewall?

You can typically purchase the NETGEAR FVS114IS ProSafe VPN Firewall from authorized network equipment retailers, electronics stores, or reputable online marketplaces to ensure you receive a genuine product.

Is the FVS114IS VPN Firewall compatible with dynamic IP addresses for remote access?

Yes, the FVS114IS VPN Firewall is often compatible with dynamic IP addresses, making it suitable for remote access configurations where the IP address of the remote client may change.

References:NETGEAR FVS114IS ProSafe VPN Firewall – Device.report

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>