tuya H6 Smart Wifi Lock User Manual

tuya H6 Smart Wifi Lock User Manual

Product Features

1. Unlock ways: Fingerprint, Password unlock, key unlock, IC card
2. Dual mode: passage/lock mode can be switched at will.
3. Low voltage alarm fun con emergency power supply interface.
4. Applicable to the 35-55mm wooden door or steel door.
5. Adapted lock body: 5050 dedicated electronic lock body
6. Suitable places: residual areas, public transport on, offices, homestays, etc.

Product functions

1. Mico USB emergency power supply interface: use power bank for emergency open when low voltage
2. Electronic switch boon: quick unlock with one boon
3. Key to unlock: use mechanical key to unlock when there is no power or electronic failure
4. Fingerprint identical on: use the registered fingerprint to unlock.
5.  digital keys/IC card inducing area: use the registered password or IC arid to unlock
6. Beery box cover: open the beery box cover to replace the bakery.
7. Reset key: fanon setting and inialization.
8. Mechanical unlock knob: use the mechanical unlock knob to unlock when there is no power or electronic failure

Note: There is no need to rotate the handle for daily opening/ closing the door

Installation

1. Cutting template: please follow the template to drill hole first
   
   Note: The buckle plate with le or right dire con differ, please follow the hole diagram for installa on
   

2. Install the lock body: first insert the lock body lock into the opened door hole (note that the end with the wire is upward), and then tighten the screws to fix the lock body, as shown in the figure below
   

3. install the studs: Take out the hollow studs from the accessories package and tighten the studs according to the position shown in the figure below, see the position 1 in the figure to screw M4X35, see the position in the figure @ screw M5X35.
   

4. Install the front panel: first confirm the door opening direction, as shown in Figure 1 below, then adjust the position of the lock cylinder connecting piece as shown in Figure 2 below, connect the lock cylinder motor wire, and then insert the panel studs and the lock cylinder connecting piece Lock body (see Figure 3 below).
   Change the dire con of the handle of the lock:
   Remove the reversing screw and adjust the dire con of the handle according to the dire con of the door. Do not install the handle in a reverse direcon Aer the mechanical key opens the door, it is easy to hit the door frame and cause damage.

5. Aer installing the back panel, first turn the handle 90 degrees, take out the beery cover, connect the cone con line and hide the excess line in the hole, and install the rear lock on the door, (note: the lock cylinder coning sheet is inserted into the cross hole of the mechanical knob on the lock surface, no falling off is allowed), align the hole with the hole and then screw on the pull screw, reference below image. Note: The mechanical knob ensures that the pulling screws are whitened under smooth opening and closing. Plosion 1 in the figure below uses M4X35 screws, plosion 2 in the figure below uses M4X45 screws.
   

6. Replace the battery: push the battery cover according to the arrow direction of the battery box cover and install the battery (note the direction of the positive and negative poles of the battery), as shown in the figure below.
   

Operating instructions

1. Unlock Informa on: refers to the entered fingerprint, password or IC card
   Informa on (including administrators and ordinary users)

2. “*” key: Clear key/Back key

3. “#” key: It is the confirm on key or the fun con key to enter the menu

4. Inala state

5. The factory administrator’s inyala password is “123456”. In the in astute, any fingerprint, IC card or password can unlock the lock.

Door lock falcon management

1. press 1 for add administrator setting press 1 for add administrator setting, please input administrator, input fingerprint or password(fingerprint input 4 mes, password input 6-8 digits number for twice, IC card swipe 1 me)

2. Please enter the serial number and press # to confirm (002#) (It cannot delete all, the first administrator will be retained)

3. Network setting
   First add at least one administrator and then operate as follows
   (note: the an-lock boon cannot be in the an-lock state)
   add network

4. Search for “Tuya Smart” in the App store or app store to download and install the App

5. Register and log in with your mobile phone number.

6. Click on the “Tuya Smart” interface to add devices, find the “Camera/Lock” and click on “Record Door Lock Wi-Fi” and follow the prompts to complete the add ion of the device and use it.

7. Lock first press “”*” and then press “#” to verify the administrator successfully and then voice broadcast 2: 1. Add user; 2. Delete user; 3. Normally open mode

8. Silent mode; 5. Time setting; 6. Add Network; 7. Delete the network, press “6”,
   voice broadcast: 1 hotspot connexon, 2 smart connexon, press “2” Voice broadcast: operon is successful.
   Note: Add successfully Voice broadcast: Opera on succeeds Add failure Voice broadcast: Opera on failed 3.5 Aer waking up the panel, enter “9#” to connect to the Internet

User setting

1. Add user
   Press “1”voice prompt: please input user informant, input fingerprint or password( fingerprint input 4 mess, password input 6-8 bit digital twice), IC card input one me. It can input another user informant after it successfully.

2. Press “2”for delete user
   Press “2”voice prompt: press “1” input number delete, press “2”delete all, press “1” input number(010#) delete success.

3. System setting

4. Press “3” voice prompt: press “1” for voice setting  ; press “2” for unlock mode setting ; press “3” language setting , press “4” me setting  , press “5” for modify room number.

5. Unlock mode setting  Press”2” voice prompt: press “1” for single unlock, press “2”for combine unlock. Press “1” voice prompt: operate success.

6. Language setting  Press “3” voice prompt: Press “1” for Chinese, press “2” for English.

7. Time setting

8. Press “4” voice prompt: present-me is 1903041153, please modify. Please modify based on the format (year-month-day, for example: 1903041153), and then press # to confirmed, it would tell you “Successful”

9. Room number modify
   Press “5” voice prompt: room number 8888, please modify. You can input 4 numbers and press # to confirm. It would tell you “Successful” 4. Restore factory setting (Press the restore key under the beery cover on the rear panel of the lock around 6-8 seconds and hear a “?Di”? beep tone, restore successfully

Other notes

1. The system will atomically enter the invalid input state if the unauthorized unlocking informant is canorously incorrectly input for more than 5 mess
   within 5 minutes, and the invalid input state will lasts for 90 seconds. Aer the voltage is lower than 4.5v, the lock will atomically alarm every me when it is opened. Aer the alarm, the lock can be opened for 200 mess. Aer the number of mess exceeds, each unlock delay is 5 seconds, new bakeries must be replaced before the number of mess available.

2. Password peeping preening fanon : Input password as follows when opening the door with password: XXX password XXX; you can add some extraneous codes before and aero the password, and then press # to confirm. The password must be included in the input contents.

3. If there is no operon more than 10 seconds , system will atomically exit.

4. inialization setting: Press the restore key under the bakery cover on the rear panel of the lock around 6-8 seconds, all the unlock informant and records will clear aero inialization(Please carefully operon)

5. Normal open mode under close status, press 5 #, voice prompt “please input unlock informant”, input unlock informant, voice prompt “Normal open mode, please a neon to lock”.

6. Normal open mode under open status, press “5#”, voice prompt “? Normal open closed)

7. An-lock fanon: Aer pressing back locking key, the voice says “the door is locked”. Now, ordinary users cannot open it, and only administrators can unlock.

8. Under inialization status, input “555666888?,support switch language of “ English and Chinese”.

Technical Parameters

I| Static Current| :::;:50uA|
---|---|---|---
2| Static average current| :,90uA|
3| Dynamic current| S250mA|
4| Administrator| 9|
5| Finger print + password ♦ car<| JOO|
6| Fingerprint head| Semi-conductor|
7| Fingerprint comparison time| ,S0.6S|
8| Fingerprint recognition degree| 360 degree|
9| False Rejection Rate| <0.1%|
10| false accept rate| !0.0001%|
II| Induction time|

:,0.1S

|
12| Power supply type| 6V|
13| Emergency power supply| 5VDC|
14| working temperature| -10°C-55°C|
15| Working humidity| 20%-90%RH|
16| Voice prompt| YES|
17| Keypad| Touch standard 12-bitkeypad|
18| Password length| 6 digits keypad|
19| lower power alarm| 4.8+0. 2V|
20| Virtual password| 16|
’21| Unlocking time| slS|

packing list

45*3.8 cross countersunk

head screw

| 2pc| KEY| 2pc
353.8 cross countersunk head screw| 1 pc| Manual| 1 pc
Certificate of Conformity| 1 pc| Mortise| 1 pc
Buckle plate| 1 pc| Plate case| 2pc
42.0 Countersunk head t app1ng screws| 2pc| Nut6x35| 3pc
Nut7.7×35| 1 pc
2.8*20 screws| 2pc| IC card| 2pc

Dimension of pane

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>