RCA 3350GDKM0306A Dual Control Troffer Instruction Manual
- June 15, 2024
- RCA
Table of Contents
Installation Manual
LED Recessed Troffer
Integrated with Sensor
3350GDKM0306A (Rev.01)
’2 x ’2
2’ x 4’
This installation manual is only valid for the following RCA LED Recessed
Troffer integrated with sensor
• For your safety, please read the「Safety Precautions」prior to installation.
Safety precautions
Failure to follow the RCA installation manual and instructions could lead to
product damage or serious physical injury.
WARNING
-
To avoid the risk of electrical shock, all electrical work must be performed as instructed in this installation manual by a licensed and qualified electrician.
-
Prior to installation, please verify and confirm all electrical circuit breakers are properly operating and functional. Designated circuits and circuit breakers should be turned OFF prior to installing the fixture.
-
Prior to installation, please verify all electrical circuitry or wiring is properly operating and functional. Please confirm the correct circuit voltage (120 V – 277 V) and polarity prior to installing fixtures.
-
To avoid the risk of electrical shock, ensure that the fixture and electrical circuits are properly grounded prior to installation.
-
Installation in areas experiencing casual water damage, flooding, or high humidity should be avoided.
This fixture is not suitable for underwater lighting purposes or water spray down applications. -
Do not install this fixture if defects are noticeable or the product has experienced damage during shipping or storage. Contact RCA Technical Support for warranty coverage and assistance.
-
Do not temporarily store nor permanently install this product near flammable objects or in areas with high risks of fire.
-
Failure to install this fixture, in its entirety and as provided by RCA Lighting Solutions, may void the warranty. RCA is not responsible for fixtures that are modified to be used in any other way than its intended purpose.
-
Do not use or install if the fixture has been damaged due to dropping or prior electrical shock. Should the product owner or installer determine the fixture is not operable, please contact RCA Technical Support for product and warranty assistance.
-
During cleaning, please attempt to minimize the use of water, alcohol, benzene, or acetone in order to avoid the risk of electrical shock as well as potential degradation of the fixture surfaces and lens.
-
To prevent damage during ceiling installation, RCA recommends having at least (2) qualified electricians assisting with the installation.
-
Operating temperature of the LED Troffer and Driver is to be maintained between -20 ℃ ~ 40 ℃ (-4℉~104℉) to comply with all safety and warranty regulation.
-
Do not install where the product may be exposed to direct sunlight.
-
Wear gloves to prevent cuts or abrasions when removing the product from carton, when handling, when installing, and when maintaining the product.
Edges can cut. Handle with care. -
Do not install nearby air conditioners and heating appliance.
-
Avoid metal and reinforced concrete walls etc, between products if you want to use its wireless communication function.
-
This product meets the electromagnetic wave standards specified by CE and FCC/IC, but it may malfunction in noisy RF environments.
-
(Example : Where strong RF transmit / receive devices or strong electromagnetic machines are used)
Installation
Bend T-Bar clips out perpendicular to T-Bar. Place the RCA
troffer into the T-Bar Ceiling panel.
Ensure T-Bar clips are attached to the T-Bar.
Remove access plate from
junction box. Using screw driver blade, remove appropriate knockout from
access plate door to route input conduit.
Connect input conduit to
access plate. Connect wires as shown in wiring diagram.
Push all wires back into the body. Re-install access plate.
(GREEN/YELLOW – Ground, WHITE – Neutral , BLACK – Live)
When the fixture is connected to the intended circuit, the installer must use
a UL approved wire connector having a flame retardence of UL94 V-0 or higher.
- This product has been manufactured and sold under the responsibility of DTI SERVICES LLC..
- RCA, the RCA logo and the two dogs (Nipper and Chipper) logo are trademarks used under license by DTI SERVICES LLC. – further information at www.rca-brand.com.
- All other products, services, companies, trademarks, trade or product names and logos referenced herein are the property of their respective owners.
Sensors information
- Smart Multi Sensor with ZigBee Dongle
- Design
- Technical data
Motion sensor| Passive Infrared(PIR) Sensor
---|---
Frequency| 2405.0 ~ 2480.0 MHz
Wireless range| Line of sight 98 ft (30 m)
Operating conditions| For Indoor use only
Humidity| 0 to 85 % Rh
Installation height| Up to 11.5 ft (3.5 m)
Light sensing range| 1 ~ 1000 lx - Motion sensing area * Height : up to 11.5 ft (3.5 m)
Height| Short side| Long side
---|---|---
8.2 ft (2.5 m)| 13.1 ft (4 m)| 16.4 ft (5 m)
11.5 ft (3.5 m)| 18.4 ft (5.6 m)| 23 ft (7 m)
H ft
H m| (1.6 x H) ft
(1.6 x H) m| (2 x H) ft
(2 x H) m -
Field adjustable sensor values (for stand-alone luminaire use only)
Default Light SettingsMax Light Level| 80%
Mid Light Level| 80%
Minimum Light Level| 0%
Motion| Enabled
Daylight| Disabled
Dim Down| N/A
Time Out| 30:00 Minutes
Sensitivity| HIGH -
Light sensing area * Height : up to 11.5 ft (3.5m)
Button ConfigurationTask Switch # of Presses| Max| Mid| Min
1| 80%| 40%| 0%
2| 60%| 40%| 0%
3| 40%| 20%| 0%
4| 100%| 40%| 0%
| Dim Down| Time Out| Total
5| 05:00 Minutes| 05:00 Minutes| 10:00 Minutes
6| 15:00 Minutes| 05:00 Minutes| 20:00 Minutes
7| 25:00 Minutes| 05:00 Minutes| 30:00 Minutes
8| 00:30 Minutes| 00:30 Minutes| 01:00 Minutes
9 (Night-light / EM Driver Mode)| 100%| 40%| 20%
10| Factory Reset
Long Presses (5 seconds hold)| Default| Rotation
---|---|---
CCT| 5000K| 5000K 4500K 4000K 3500K 3000K
CAUTION:
Make sure that the number of troffer reaction is same with the number of times
you pressed the button.
- Factory reset
– Turn the main power on and off 10 times in a row.
– Press “Task switch” on the sensor 10 times in a row.
RCA SENSOR CONNECT
RCA SENSOR CONNECT is the stand-alone system that doesn’t need any additional
control devices except sensor-embedded troffers.
For further details, please consult sales representatives.
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION
CODE BY A PERSON FAMILLIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT
AND THE HAZARDS INVOLVED
FCC Notice :
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference and
- this device must accept any interference received, including interference that may cause undesired operation of the device.
Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FCC RF Radiation Exposure Statement :
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter.
This equipment should be installed and operated with a minimum distance of 20
cm (7.8 inches) between the antenna and your body.Users must follow the
specific operating instructions for satisfying RF exposure compliance.
Contains FCC ID : TGEACM20ZEA1
Responsible Party :
RCA Lighting Solutions
5935 W. 84th Street, Suite A,
Indianapolis, In 46278
www.rcaled.com
Phone. 800-722-2161
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>