Smart Panlee ZX2D10GE01R-V4848 Rotary Switch Screen Instruction Manual
- June 13, 2024
- Smart Panlee
Table of Contents
Smart Panlee
Rotary Switch Screen
ZX2D10GE01R-V4848
Shenzhen QM Smart Panlee Technology Co., Ltd.
Features:
1. Support rapid prototyping
Core Materials (Tab. 0):
| No. | Name | Model | Remark |
|---|---|---|---|
| 1 | ESP32-S3 module | WT32-S3-WROVER-N16R8 | |
| 2 | |||
| 3 |
Hardware Interface:
Hardware Interface Diagram:
Interface Description:
[1] LCD Interface (Tab.1)
| Description | Module Pin | Remark |
|---|---|---|
| _TPSCL | GPIO 6 | Touch IIC bus clock, reused with external |
interface, no touch at present
TP_SDA| GPIO 5| Touch IIC bus data, reused with external
interface, no touch at present
TP_INT| GPIO 7| Touch interrupt, no touch at present
LCD_RST| EN| –
LCD_CS| GPIO 21| LCD SPI bus CS
LCD_SCLK| GPIO 47| LCD SPI bus SCLK
LCD_MOSI| GPIO 41| LCD SPI bus MOSI
RGB_PCLK| GPIO 45| LCD RGB interface PCLK
RGB_DE| GPIO 39| LCD RGB interface DE
RGB_VS| GPIO 48| LCD RGB interface VS
RGB_HS| GPIO 40| LCD RGB interface HS
RGB_D0| GPIO 47| LCD RGB interface D0
RGB_D1| GPIO 41| LCD RGB interface D1
RGB_D2| GPIO 0| LCD RGB interface D2
---|---|---
RGB_D3| GPIO 42| LCD RGB interface D3
RGB_D4| GPIO 14| LCD RGB interface D4
RGB_D5| GPIO 8| LCD RGB interface D5
RGB_D6| GPIO 13| LCD RGB interface D6
RGB_D7| GPIO 18| LCD RGB interface D7
RGB_D8| GPIO 12| LCD RGB interface D8
RGB_D9| GPIO 11| LCD RGB interface D9
RGB_D10| GPIO 17| LCD RGB interface D10
RGB_D11| GPIO 10| LCD RGB interface D11
RGB_D12| GPIO 16| LCD RGB interface D12
RGB_D13| GPIO 9| LCD RGB interface D13
RGB_D14| GPIO 15| LCD RGB interface D14
RGB_D15| GPIO 46| LCD RGB interface D15
LCD_BL| GPIO 38| LCD backlight control, active high
[2] FPC Connector Interface (Tab.2)
| Pin | Description | Module Pin | Voltage Range | Remark |
|---|---|---|---|---|
| 1 | ESP_TXD | TXD0 | 3.3V TTL | Download serial port TXD |
| 2 | EXT_IO4 | GPIO 1 | 0~3.3V | Output interface 4 |
| 3 | ESP_RXD | RXD0 | 3.3V TTL | Download serial port RXD |
| 4 | EXT_IO3 | GPIO 2 | 0~3.3V | Output interface 3 |
| 5 | EN | EN | 0~3.3V | Chip enable |
| 6 | EXT_IO2 | GPIO 20 | 0~3.3V | Output interface 2, multiplexed with USB |
| 7 | BOOT | GPIO 0 | 0~3.3V | Boot mode select |
| 8 | EXT_IO1 | GPIO 19 | 0~3.3V | Output interface 1, multiplexed with USB |
| --- | --- | --- | --- | --- |
| 9~12 | GND | – | 0V | Ground |
| 13、14 | USB_DP | GPIO 20 | 0~3.3V | USB pin, which can be used as general IO |
| 15、16 | USB_DN | GPIO 19 | 0~3.3V | USB pin, which can be used as general IO |
| 17、19 | ICCInterface | – | – | Not connected in the current version |
| 18、20 | +5V | – | +5V±5% | 5V power supply |
[3] Download Interface (Tab.3)
| Pin | Description | Module Pin | Voltage Range | Remark |
|---|---|---|---|---|
| 1 | +5V | – | +5V±5% | 5V power supply |
| 2 | BOOT | GPIO 0 | 0~3.3V | Boot mode select |
| 3 | EN | EN | 0~3.3V | Chip enable |
| 4 | ESP_RXD | RXD0 | 3.3V TTL | Download serial port RXD |
| 5 | ESP_TXD | TXD0 | 3.3V TTL | Download serial port TXD |
| 6 | GND | – | 0V | Ground |
Hardware Peripherals:
| Peripheral | Description | Related IO |
|---|---|---|
| Button | The button is pulled up, grounded when pressed | GPIO 3 |
| LCD | LCD with RGB interface, no touch, 480 * 480 | – |
| LED | Single bus LED, 13 in total | GPIO 4 |
| --- | --- | --- |
| Hall encoder | Hall encoder is used for rotating operation in human-computer | |
| interaction, and orthogonal encoder is adopted. | GPIO 5、6 | |
| Vibrating motor | Feedback for human-computer interaction | GPIO 7 |
Schematic ：
Specification Parameters:
[1] LCD Parameters (Tab.5)
| Display Type | IPS |
|---|---|
| Driver IC Model | ST7701S |
| Viewing Angle | Full Veiw |
| Resolution | 480*480 |
| Interface | RGB |
| Color | RGB565 |
[2] Touch Parameters (Tab.6)
| Touchscreen Type | – |
|---|---|
| Driver IC Model | – |
| Interface | – |
| Touc hsc reen Structure | – |
| Touch Mode | – |
| Surface Hardness | – |
| Light Transmittance | – |
Outline Dimensional Drawing (Fig.2)
Firmware Burning:
- Connect the downloader (ZXACC-ESPDB) via a USB-Type C cable. And then connect the ZX2D10GE01R board with the downloader (ZXACC-ESPDB) through an MX1.25-7P cable. As the downloader (ZXACC-ESPDB) has automatic data flow processing capabilities, the firmware can be downloaded automatically through the ESP32 Flash Download Tools.
- As shown in Fig. 4: Select the firmware path at mark 1, and then fill in the burning address, usually 0X00. Note that this checkbox must be checked; Set the crystal frequency to be 40MHz at mark 2; Select 32Mbit for Flash size at mark 3; Select DIO for SPI MODE at mark 4; Select the COM port number recognized by the computer at mark 5; Select the baud rate at mark 6 (the higher the value is, the faster the firmware will be downloaded. Max. 1152000bps).
- After the previous configuration, click START at mark 7 to start burning the firmware.
- Complete the above steps, and then press the reset button on the back of the development board to start running the firmware you just burned.
Software design reference ：
URL：https://www.espressif.com.cn/en/support/documents/technical-documents
Online GUI Designer:
Users can use our online GUI designer platform, which is similar to MIT APP
Inventor, to realize the rapid GUI development with building blocks.
Currently, the platform has perfected the graphic interface development, and
more driver code blocks will be further improved in the future.
Login Page: http://8ms.xyz/login
User Manual: https://doc.smartpanle.cn/ESP32-S3/index.html
Fig.6
Contact Us
URL: http://www.panel-tag.cn/
E-mail: panlee@smartpanle.com
Get Samples: https://shop212317088.taobao.com/
Wechat Official Account: Smartpanle
http://weixin.qq.com/r/IxJ5YTLEiG-3rXYC90cx
ZX2D10GE01R-V4848 Datasheet
henzhen QM Smart Panlee Technology Co., Ltd.
References
- 8ms创新视界
- 彩屏方案-串口屏规格-hmi触摸屏-智慧屏-深圳市启明智显科技有限公司
- shop212317088.taobao.com/
- Technical Documents | Espressif Systems
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>