Fleurco ARTUS MFA LED Mirror User Guide

Installation and User’s Guide

Read all instructions carefully before proceeding.
Record the serial number on the back page and save this guide for future reference.

BEFORE BEGINNING

• Carefully read the instructions before beginning the installation.
• DANGER! To avoid the risk of electrocution, please turn off the electricity mains before commencing the installation.
• WARNING: Risk of Electric Shock – Connect this to a properly grounded outlet only. See Grounding Instructions
• It is strongly recommended that this installation be performed by a professional electrician.
• It is recommended that you wear safety glasses at all times during the installation.
• It is recommended to have two people for this installation
• This product is wall mounted only. Do not use outdoors.
• Never drop or insert any object into any opening
• Do not operate where aerosol (spray) products are being used or where oxygen is being administered
• To disconnect, turn off the device, then remove plug from outlet
• Never operate this product if it has a damaged cord or plug, or if dropped into water.
• Keep the cord away from heated surfaces.
• Children must be supervised while using this product.

CAUTION

WARNING
To avoid the risk of electrocution, please turn off the electricity mains before commencing the installation. We recommend the mirrors gets fitted by a qualified electrician.

THANK YOU
We can assure you that FLEURCO has used the best materials and has applied the strictest quality control measures to ensure that each and every unit meets the highest quality standards. This booklet contains general information about  the unit as well as step-by-step installation instructions.

MAINTENANCE

Never use scouring powder pads, abrasive material, strong bleach or sharp instruments on metal components or glass. An occasional wiping down with a mild soap diluted in water is all that is needed to keep the mirror and aluminum  parts looking new. Test products on a small inconspicuous surface prior to use.

TOOLS AND MATERIALS REQUIRED

HARDWARE LISTING

Select the desired position of the mirror. Ensure that there is a junction box within reach of the 45” long power cord.

ELECTRICAL BOX PLACEMENT

Place and level the mirror on the wall. Mark the location of the frame.

MARQUER ET FIXER LE SUPPORT
Mark a line 1 3/4” below the mark from Step 1. Place the hanging bracket(s) so the centers of the holes sit on the new line. Mark the hole locations, ensuring they are level. If a larger mirror is to be hung on 2 brackets, ensure they are in  line and level. 

Drill the holes and insert wall plugs.

Fasten the hanging bracket to the wall.

CONNECTING ELECTRICAL WIRING
Connect the electrical wiring by following the diagram below.

PLEASE NOTE: The colors referenced in the diagram above is based on conventional standards and may differ between households. If there is any confusion as to how these should be connected, please seek the help of a licensed  professional electrician. Electric shock, fire hazard and death are possible consequences of poor wiring for none of which Fleurco will be held liable.

HANG THE MIRROR
Slide the mirror down onto the bracket(s).

POWER BUTTON*. SHORT PRESS FOR LIGHT AND DEFOGGER ON/OFF.
LONG PRESS TO ADJUST LIGHT BRIGHTNESS.
COLOR TEMPERATURE SELECTOR (3000K, 4500K, OR 6500K). SHORT PRESS FOR COLOR TEMPERATURE SELECTOR. LONG PRESS TO GRADUALLY CYCLE THROUGH THE OPTIONS.

• TO TURN OFF THE BUTTON’S LIGHT, HOLD BUTTON WHEN THE MIRROR LIGHT IS OFF.

SPECIFICATIONS

Models:

(914mm)
MFA2436| 24″
(610mm)| 36″
(914mm)
MFA3036| 30″
(762mm)| 36″
(914mm)
MFA3636| 36″
(914mm)| 36″
(914mm)

(914mm)
MFA2436| 48″
(610mm)| 36″
(914mm)
MFA3036| 54″
(762mm)| 36″
(914mm)
MFA3636| 72″
(914mm)| 36″
(914mm)

Save this manual for future reference

Purchase date____
Paste packaging label_____

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>