WATER CREATION F2-0012 Lavatory Faucet Mirror Installation Guide

WATER CREATION F2-0012 Lavatory Faucet Mirror Installation Guide

Tools for Assembly (Not Included)

• Electric Drill with #2 Drill Bit

• 1/8″ Drill Bit

• Tape Measure

• Builder’s Pencil

• Level

Supplies (Included in Package)

• Wall Anchor (2pcs)

• Screw (2pcs)

Assembly

1. Flip the mirror over and measure the distance between point and point .

2. Use a level to mark the measured distance between Point and Point on the wall.

Note:
The distance from @ + should be equal to + ©.

3. Drill 2 holes at the marked positions and insert wall anchors and screws.

IMPORTANT:
PLEASE NOTE THAT THE SCREWS PROVIDED MAY NOT BE SUITABLE FOR ALL WALL TYPES.IT IS IMPORTANT TO CONSULT AN EXPERT TO DETERMINE THE APPROPRIATE SCREWS OR BOLTS FOR YOUR SPECIFIC WALL CONSTRUCTION.

4. Hang the mirror on the wall.

Thank you for choosing Water Creation. Your safety is our top priority, and we hope these instructions help you use our products safely and effectively.

LAVATORY FAUCET INSTALLATION GUIDE B

BEFORE YOU BEGIN

1. Shut off water supply.
2. Carefully inspect waste and supply tubing for signs of damage.
3. Replace waste or supply tubing if necessary

A) SPOUT INSTALLATION

1. Remove lock nut and connect tee.
2. Apply plumbers’ putty or sealant.
3. Locate mounting hole and insert spout into deck or lavatory.
4. Screw and tighten washers, lock nut onto the shank and secure the spout.
5. Screw and tighten the connect tee to the shank.
6. Remove excessive plumbers’ putty or sealant.

Half turn loosen the tee for ideal position to connect with hoses

TOOLS AND MATERIALS

• Basin Wrench

• Adjustable wrench

• Teflon Tape

• Pipe Wrench

• Screwdriver

• Flexible Water Supply Line

B) HANDLE VALVE INSTALLATION

1. Connect the longer flex hose to valve body.
2. Place lower plastic washer and lock nut over valve body.
3. Insert valve body from under the sink.
4. Place upper rubber washers and escutcheon on valve spindle
5. Adjust position of valve body and secure with lock nut and escutcheon.
6. Place handle on spindle and tighten with screw.

C) FLEXIBLE HOSE INSTALLATION

1. Connect flexible hoses to supply tee.
2. Secure hoses with wrench. Do not over tighten.
3. Circle the excessive part of hoses as shown in figure below.

D) DRAIN WASTE INSTALLATION

1. Disassemble the drain.
2. Apply plumbers’ putty or sealant to bottom side of flange. (Or use attached rubber washer to instead of putty)
3. Insert drain body through sink.
4. Attach the gasket, Teflon washer and tighten the lock nut.
5. Apply Teflon tape to the drain pipe threads and screw with drain body
6. Remove excessive plumbers’ putty or sealant

E) SUPPLY CONNECTION

1. Install lavatory according to manufacturer’s instructions.

2. Connect hoses (not provided) to angle stops.

3. Tighten all connections.
   VERY IMPORTANT

4. Flush out water for two minutes before connect hose to faucet valve.
   (This act to avoid debris trapped the flow regulator)

F) INSTALLATION CHECKOUT

1. Ensure all connections are tightened properly.
2. Turn on main water supply.
3. Turn on and off cold and hot water respectively.
4. Turn on both hot and cold water and turn off. Check for leaks.
5. Remove the aerator cap and aerator. Check for debris. Clean of necessary.
6. Reinstall aerator.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>