NATIONAL INSTRUMENTS USB-6366 USB X Series Mounting Kit Installation Guide
- June 13, 2024
- NATIONAL INSTRUMENTS
Table of Contents
NATIONAL INSTRUMENTS USB-6366 USB X Series Mounting Kit
Product Information
The USB-6343 is a device from the USB X Series, designed to be mounted on a wall or panel. It comes with a USB X Series Mounting Kit that includes a backpanel wall mount and a front bracket. Additionally, there is an option to use a DIN rail clip for mounting on a standard DIN rail.
USB X Series Mounting Kit Installation
- Attach the backpanel wall mount to the wall or panel using three #8-32 flathead screws.
- Refer to Figure 2 for the dimensions of the backpanel mounting holes.
- Place the USB X Series device on the backpanel wall mount with the signal wires facing down and the device bottom sitting on the backpanel wall mount lip.
- Attach the front bracket to the backpanel wall mount by tightening the two thumbscrews.
USB X Series Mounting Kit with DIN Rail Clip Installation
- Attach the DIN Rail Clip to the backpanel wall mount.
- Clip the bracket onto the DIN rail.
- Place the USB X Series device on the backpanel wall mount with the signal wires facing down and the device bottom sitting on the backpanel wall mount lip.
- Attach the front bracket to the backpanel wall mount by tightening the two thumbscrews.
For the USB X Series Mounting Kit and USB X Series Mounting Kit with DIN Rail Clip
You can mount your USB X Series device to a wall or panel as described in the USB X Series Mounting Kit Installation section, or mount it to a standard DIN rail as described in the USB X Series Mounting Kit with DIN Rail Clip Installation section.
Mounting Kit Installation
USB X Series Mounting Kit Installation
Complete the following steps to mount your USB X Series device to a wall or panel using the USB X Series mounting kit. Refer to Figure 1.
- Use three #8-32 flathead screws to attach the backpanel wall mount to the panel/wall. Tighten the screws with a #2 Phillips screwdriver to a torque of 1.1 N · m (10 lb · in.).
- Place the USB X Series device on the back panel wall mount with the signal wires facing down and the device bottom sitting on the backpanel wall mount lip.
- While holding the USB X Series device in place, attach the front bracket to the back panel wall mount by tightening the two thumbscrews.
USB X Series Mounting Kit with DIN Rail Clip Installation
Complete the following steps to mount your USB X Series device to a DIN rail using the USB X Series mounting kit with DIN rail clip.
- Fasten the DIN rail clip to the back of the backpanel wall mount using a #1 Phillips screwdriver and four machine screws (part number 740981-01), included in the kit, as shown in Figure 3. Tighten the screws to a torque of 0.4 N · m (3.6 lb · in.).
- Clip the bracket onto the DIN rail as shown in Figure 4.
- Place the USB X Series device on the backpanel wall mount with the signal wires facing down and the device bottom sitting on the backpanel wall mount lip.
- While holding the USB X Series device in place, attach the front bracket to the backpanel wall mount by tightening the two thumbscrews.
LabVIEW, National Instruments, NI, ni.com, the National Instruments corporate logo, and the Eagle logo are trademarks of National Instruments Corporation. Refer to the Trademark Information at ni.com/trademarks for other National Instruments trademarks. Other product and company names mentioned herein are trademarks or trade names of their respective companies. For patents covering National Instruments products/technology, refer to the appropriate location: Help»Patents in your software, the patents.txt file on your media, or the National Instruments Patent Notice at ni.com/patents.
© 2010 National Instruments Corp. All rights reserved.
References
- Test and Measurement Systems, a part of Emerson - NI
- NI Trademarks and Logo Guidelines - NI
- USB-6343 National Instruments Multifunction I/O Device | Apex Waves