waterpik SF-03 Black Sonic Fusion 2.0 Flossing Toothbrush User Manual
- June 13, 2024
- Waterpik
Table of Contents
waterpik SF-03 Black Sonic Fusion 2.0 Flossing Toothbrush User Manual
IMPORTANT SAFEGUARDS
READ ALL INSTRUCTIONS BEFORE USING
- This product is for household use.
When using electrical products, especially when children are present, basic safety precautions should always be followed, including the following:
DANGER:
To reduce the risk of electrocution:
- Do not handle plug with wet hands.
- Do not place in or drop into water or other liquid.
- Do not use while bathing.
- Do not place or store product where it can fall or be pulled into a tub or sink. Sonic–Fusion 2.0 Brush Floss Speed
- Do not reach for a product that has fallen into water. Unplug immediately.
- Check the power supply cord for damage before the frst use and during the life of the product.
WARNING:
To reduce the risk of burns, electrocution, fire, or injury to persons:
- Do not direct water into the nose or ear. The potentially deadly amoeba, Naegleria fowler, may be present in some tap water or unchlorinated well water and may be fatal if directed into these areas.
- Use this product only as indicated in these instructions or as recommended by your dental professional.
- Only use fossing brush heads and accessories recommended by Water Pik, Inc.
- Do not drop or insert any foreign object into any opening or hose.
- Keep electrical cord away from heated surfaces.
- Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.
- Fill reservoir with water or other dental professional recommended solutions only.
- Remove any oral jewelry prior to use.
- Do not use if you have an open wound on your tongue or in your mouth.
- If your physician or cardiologist has advised you to receive antibiotic premedication before dental procedures, you should consult your dentist and/or medical professional before using this product or any other oral hygiene aid.
- Do not use iodine or water insoluble concentrated essential oils in this product.Use of these can reduce product performance and will shorten the life of the product. Use of these products may void warranty.
- Magnetic feld: Pacemakers and similar implanted medical devices may be afected by magnet. Contact your doctor with any questions.
- Do not use the toothbrush motor for more than 5 minutes in each 10 minute period.
- This product does not contain any user serviceable parts. Do not attempt to open.
- Using toothpastes containing peroxide may damage the plastic housing of this product.
- Using abrasive or chemical cleaners may damage the plastic housing of this product.
- This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
- Children should be supervised to ensure that they do not play with the appliance.
- The supply cord cannot be replaced. If the cord is damaged the appliance should be scrapped.
- Do not use this product if it has a damaged cord or power supply, if it is not working properly, if it has been dropped or damaged, or dropped into water. Contact Water Pik, Inc. or visit www.waterpik.com.
- IMPORTANT This device uses wireless communication to control the ON/OFFfunction of the water fosser pump motorfrom the toothbrush power handle. To avoid electromagnetic interference, do not operate this device in restricted locations such as aircraf or specially marked areas in hospitals.
PRODUCT DESCRIPTION
- Brush head
- Water fusser nozzle
- Hinged lid
- Reservoir
- Water hose
- Water fusser pressure control dial
- Water hose release button
- Toothbrush ON/OFF button 2
- Motion activated ring lights* 1
- Water fosser ON/OFF button
- Toothbrush speed control
- Toothbrush speed indicator Lights
- Toothbrush charge indicator lights
- Power cord
- Charging base
- Wireless connection light
- Magnetic brush head holder*
Compact size brush head
Full size brush head*
Replacement brush heads may be purchased online at www.waterpik.com, or by phone from Water Pik, Inc. at 1-800-525-2774 (USA). To fnd detailed information please visit our website at www.waterpik.com.
PREPARING THE UNIT / BRUSHING AND FLOSSING
PREPARING THE UNIT
Powering the Unit
Plug the cord into an electrical outlet. If the outlet is controlled by a wall
switch, be sure it is turned on.
Attaching the Brush Head to the Power Handle
Position the brush head on the power handle as shown. Press frmly until it
clicks into place. To remove, frmly pull the brush head to separate it from
the power handle.
Attaching the Power Handle to the Hose
Position the power handle onto hose in the base. Press the power handle frmly
onto the hose attachment until it clicks into place. To remove, simply press
the round button on the back side of the power handle.
Charging the Sonic-Fusion® 2.0 Power Handle
For a full charge, leave the handle on the charging base for at least 4 hours.
If the toothbrush is to be stored for an extended period of time (six months
or more), be sure to fully charge it (at least 4 hours) prior to storage.
Charge Lights
Toothbrush charge indicator lights will indicate level of battery charge for
approximately 10 seconds afar removal from the charging base and afer use, and
will then turn of. If only the bottom light is lit, then recharging is
recommended to ensure uninterrupted use.
Wireless Connection Light
Blue light indicates the fusser base unit is communicating via Wireless
Communication and is “Ready” for activation via FLOSS button.
Preparing the Reservoir
Remove reservoir and open hinged lid. Fill the reservoir with warm water.
Close the lid and replace the reservoir on the base and press firmly.
Prime Unit (First Time Use Only)
Floss Point tip into sink. Press FLOSS button to turn water on. Rotate
pressure knob repeatedly between high and low until water flows. Afar water
flows from the nozzle, press the FLOSS button to turn water OFF.
BRUSH
Place the brush head in your mouth before pressing the BRUSH button
Recommended Technique
For best results, position brush along gamine at a 45-degree angle. Press the
BRUSH button to turn the brush ON. Use light pressure and move the toothbrush
slowly allowing for the sonic action to clean each tooth individually. Brush
can be easily disconnected from the hose if desired (See diagram on product
description page).
Quad Timer
The Sonic-Fusion® 2.0 will create a short pause every 30 seconds to remind you
to move to the next section of your mouth. You will brush the outside of the
teeth for 30 seconds and then the inside for 30 seconds. This will be repeated
on the other arch for a total of 2 minutes to clean all teeth.
2-Minute Timer
The brush will automatically shut of afer 2 minutes of run time.
Brush Speeds
The Sonic-Fusion® 2.0 toothbrush gives you the option to choose between two
brushing speeds: High and Low. If you wish to change to a different speed, you
can do so by pressing the Speed button while brushing. The LED’s below the
Speed button indicate the current selection. High: 2 LEDs ON, Low: 1 LED ON.
FLOSS
Always place the brush head in your mouth prior to pressing the FLOSS button. Lean over the sink and slightly close lips enough to prevent splashing while still allowing water to fow from mouth into sink
Adjusting the Pressure Setting
Turn the water fosser pressure control dial on the base of the unit to the
lowest setting (pressure setting No. 1) for frst-time use. Gradually increase
pressure over time to the setting you prefer – or as instructed by your dental
professional.
Recommended Technique
For best results, start with the back teeth and work toward the front teeth.
Direct the brush head so that the water fosser nozzle is angled slightly
toward the germline. Move the brush head along the germline pausing brief
between each tooth to allow water to clean between teeth. Continue until you
have cleaned the inside and outside of both the upper and lower teeth. When
finished, empty any liquid lef in the reservoir.
NOTE: If you used mouthwash or any other solution besides water, see “Using Mouthwash and Other Solutions” section.
BRUSH + FLOSS
To Brush + Floss at the same time, place brush head in mouth. Press BRUSH button, then press FLOSS button.
CARE AND MAINTENANCE
Travel and Hose-Free Brushing
Toothbrush can be disconnected from the Sonic-Fusion® 2.0 for travel or hose-
free brushing. Place the handle and desired brush head(s) in the provided case
for protection when traveling.
NOTE: To disconnect the toothbrush from the water hose, press the round button on the back side of the power handle. See Product Description section.
Using Mouthwash and Other Solutions
Your Waterpark® Sonic-Fusion® 2.0 can be used to deliver mouthwash and
antibacterial solutions. Afer using any special solution, rinse unit to
prevent clogging by partially fling reservoir with warm water and running unit
with brush head pointed into sink.
CARE AND MAINTENANCE
Before cleaning, unplug from the electrical outlet.
After Each Use
- Afar each use, when all functions are turned OFF, remove the brush head from the handle and rinse brush head under running water.
- Wipe the handle dry afer each use.
General Cleaning / Removing Hard Water Deposits
- Clean the product when necessary by using a sof cloth and mild non-abrasive cleanser.
- Hard water deposits may build up in your unit, depending on the mineral content of your water. If lef unattended, it can hinder performance. Cleaning internal parts: add 2 tablespoons of white vinegar to a full reservoir of warm water. Point the handle and brush head into sink. Turn Water Flosser ON and run until reservoir is empty. Rinse by repeating with a full reservoir of clean warm water. This process should be done every 1 to 3 months to ensure optimal performance.
Leakage
If leaking due to a damaged hose, replacement hoses can be purchased at
www.waterpik.com or contact Water Pik, Inc.
customer service for a self service repair kit.
SONIC-FUSION TOOTHBRUSH RESET INSTRUCTIONS
In the event that your Sonic-Fusion 2.0 becomes ON/OFF unresponsive, there are two ways to reset your water fosser/toothbrush.
Radio Reset Steps:
- Unplug the fosser base unit, wait 1 minute, Re-Plug base unit to AC-Mains. This performs a base radio reset.
- Press and hold the Toothbrush BRUSH button. Then sequentially Press and hold the SPEED mode button; continue holding both buttons simultaneously. The toothbrush may run for 3 seconds and then automatically shut of at the
- second interval.
- Continue to HOLD BOTH buttons for 5 seconds.
- Afer 6 seconds RELEASE BOTH BUTTONS. This shall reset the toothbrush to factory defaults. The toothbrush fuel gauge will also reset back to empty.
- Place toothbrush in charging dock allowing radios to re-connect and begin a charging cycle. Note: the toothbrush will not run until adequate battery charge is provided back to the toothbrush indicated with at least a single solid(non-fashing) fuel gauge light.
Toothbrush Reset Steps:
- Press and hold the toothbrush FLOSS button for a duration of 10 seconds.
- Afer 10+ seconds, release the FLOSS button. At this point the toothbrush is reset to factory defaults. The toothbrush fuel gauge will also reset back to empty.
- Place toothbrush in charging dock allowing radios to re-connect and begin a charge cycle. Note: the toothbrush will not run until adequate battery charge is provided back to the toothbrush indicated with at least a single solid (non-fashing) fuel gauge light.
Battery Removal
This product contains a rechargeable Lithium-Ion battery. The battery is not
replaceable. Please do not dispose of the unit in the household waste. Remove
the batteries per the instructions below and recycle at your local recycling
center.
Note: This process is not reversible.
Remove the battery only at the end of the product’s life for recycling. Doing so earlier will destroy the product. Deplete the battery charge until the brush no longer operates. Observe basic safety precautions to protect your eyes, hands, fngers, and work surface. Remove the battery as shown and recycle them and the rest of the product according to local regulations.
- Run down the battery by operating the brush button until the motor does not run.
- Obtain a towel or cloth, hammer, fat-head screwdriver, and wire cutters.
- Remove and discard the brush head.
- Cover the handle entirely with the towel or cloth.
- Clamp the top of the handle against your work surface with one hand and strike the handle housing around the bottom perimeter on all sides to release the end cap latch. Continue striking and rotating the handle until the end cap releases.
- Remove the internal components by turning the handle upside down and while holding on to the handle housing, press the shaf down frmly on a hard surface.
- The internal components should slide out when the handle is positioned upside-down. If this does not occur, repeat steps 5 and 6 until the components release.
- Remove the end cap from the internal assembly.
- Slide the battery out of the internal assembly.
- Cut the battery wires one at a time with the wire cutters.
- Recycle and dispose of the battery properly.
- The remaining product pieces should be discarded appropriately.
LIMITED THREE YEAR WARRANTY
Service Maintenance
Waterpark® Sonic-Fusion® 2.0 has no consumer-serviceable electrical items and
does not require routine service maintenance. For all accessories go to
www.waterpik.com. You may also call our toll-free
customer service number at
1-800-525-2774. Refer to the serial and
model numbers in all correspondence. These numbers are located on the bottom
of your unit. Still have questions? Go to www.waterpik.com.
Water Pik, Inc. warrants to the original consumer of this product that it is
free from defects in materials and workmanship for 3 years from the date of
purchase.
Consumer will be required to submit the original purchase receipt as proof of
purchase date and if requested, the entire product, to support a warranty
claim. Water Pik, Inc. will replace, at its discretion, the product which in
its opinion is defective, provided the product has not been abused, misused,
altered or damaged afer purchase, was used according to instructions, and was
used only with accessories or consumable parts approved by Water Pik, Inc.
This limited warranty excludes accessories or consumable parts such as tips
and brush heads. This warranty gives you specifc legal rights. You may also
have other rights that vary, depending on the law in your place of residence.
WATER PIK, INC. DISCLAIMS ALL OTHER EXPRESS OR IMPLIED WARRANTIESTO THE EXTENT PERMITTED BY LAW INCLUDING, BUT NOT LIMITED TO, ALL WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. ALL IMPLIED WARRANTIES ARE LIMITED TO THE DURATION OF THIS LIMITED WARRANTY. SOME STATES OR PROVINCES MAY NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE MAY NOT APPLY TO YOU.
For USA Only
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that ma cause undesired operation.
Warning: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment of and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit diferent from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Limitation of Liability
This limited warranty is your sole remedy against Water Pik, Inc. and it shall
not be liable for any damages, whether direct, indirect, incidental, special,
consequential, exemplary or otherwise, including but not limited to property
damage, arising out of any theory of recovery, including statutory, contract
or tort.
Arbitration
BINDING ARBITRATION AND WAIVER OF RIGHT TO ASSERT MATTERS IN COURT AND RIGHT TO JURY TRIAL.
By purchasing, installing, or using this product you agree that any
controversy or claim arising out of or relating to your purchase, use,
modification, installation, or removal of this product shall be settled by
binding arbitration. The arbitrator’s decision will be foal and binding.
Judgment on the award rendered by the arbitrator may be entered in any court
having jurisdiction over the matter. Further, you agree that you will not have
the right to litigate any claim arising out of or in relation to your
purchase, use, modification, installation, or removal of this product in any
court or to have a jury trial on that claim.
Arbitration of any matters shall be administered by the American Arbitration
Association and conducted by one arbitrator in accordance with the consumer
arbitration rules of the American Arbitration Association in efect at the time
of fling of the demand. The venue for all such arbitrations shall be Colorado
and any such arbitration shall be subject to the Federal Arbitration Act and
Colorado law.
WAIVER OF RIGHT TO PARTICIPATE IN CLASS ACTIONS OR PURSUE CLAIMS IN A REPRESENTATIVE CAPACITY.
Further, by purchasing, installing, or using this product you agree that arbitration must be on an individual basis. This means neither you, nor we, may join or consolidate claims in arbitration by or against other purchasers or users of Water Pik, Inc. products or the general public. Additionally, you may not litigate in court or arbitrate any claims as a representative or member of a class or in a purported representative capacity on behalf of the general public, other purchasers or users of this product, other persons or entities similarly situated, or in a private attorney general capacity.
For Canada Only
This device complies with Innovation, Science and Economic Development Canada
(ISED)’s license-exempt RSSs. Operation is subject to the following two
conditions: (1) This device may not cause interference; and (2) This device
must accept any interference, including interference that may cause undesired
operation of the device.
Water Pik, Inc.,a subsidiary of Church & Dwight Co., Inc.
1730 East Prospect Road
Fort Collins, CO 80553-0001 USA
1-800-525-2774
www.waterpik.com
Made in China. Designed and tested in the U.S.A.
Form No. 20028977-F AC
©2022 Water Pik, Inc.
References
- Waterpik® Official Canadian Site: Oral Health & Shower Heads
- Waterpik™ Oral Health - Water Flossers, Electric Toothbrushes
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>