RALPH LAUREN IG RL5230GIS Relative Lighting User Guide

RL5230GIS Relative Lighting
User Guide

IG RL5230GIS Relative Lighting

NOTICE:
This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect items and contents carefully. If any damage or defect is found, do not install it.
Retain all packaging material until installation is complete and approved.

1. Carefully remove all parts from the box.

2. Thread the top ring (H) to the top of the fixture body (J).

3. Install the crossbar (B) with ceiling loop (D) to the outlet box by mounting screws (C) provided.

4. Unscrew the threaded collar on the chain end link and attach it to the top ring (H). Close the threaded collar to secure the fixture body.

5. Let canopy (E) and lock collar (F) go through the chain (G).

6. With the fixture dimension as a guide, shorten the chain (G) as needed using a pair of chain pliers.

7. Unscrew the threaded collar on the other chain end link, raise the fixture then attach the chain end link to the ceiling loop (D). Close the threaded collar to secure it.

8. Unwrap the wiring from the top of the fixture body. Weave the power supply cord and the ground wire through the chain (G).

9.  When you reach the canopy and ceiling loop, measure the wires then cut. Be certain to leave enough to connect inside the outlet box.

10.  Strip the insulation back on the two power supply wires about 5/8″.

11. Twist the power supply and ground wire together and push through the center hole of the ceiling loop (D).

12. Connect the fixture ground (bare) wire with the ground wire from the outlet box using wire nut (A) . If your house does not have ground wire, then attach this wire to the green grounding screw inside of the outlet box.
    IT IS IMPERATIVE THAT THIS FIXTURE BE GROUNDED.

13. Connect the fixture Neutral (ribbed, no markings) wire with the neutral wire from the outlet box using wire nut (A).

14. Connect the fixture Hot (smooth edge, markings) wire with the hot wire from the outlet box using wire nut (A).
    DO NOT REVERSE THE HOT AND NEUTRAL CONNECTIONS OR SAFETY WILL BE COMPROMISED.

15. Tuck these wire connections neatly into the outlet box to secure them.

16. Put canopy (E) to the ceiling loop (D) and secure it with a lock collar (F).

17.  Put the glass disk (K) over the candle tube.

18. Attach the glass disk (N) to the fixture body and secure it with a plastic washer (M) and crystal column (L).

19. Insert bulbs (not included) into the sockets.

20. Clip the shade (I) onto the bulbs.

21. Installation is complete, turn on the power at the fuse or circuit breaker.

Care Instructions: Clean only with a soft dry cloth or feather duster. Do not use abrasive or chemical agents.

NOTICE:
This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect items and contents carefully. If any damage or defect is found, do not install it.
Retain all packaging material until installation is complete and approved.

Install the crystal drops:

1. Hang the crystal drop (A) on the hook (A1).
2. Hang the crystal drops (B) on the hook (B1).
3. Hang the crystal drops (C) on the hook (C1).
4. Hang the crystal drops (D) on the hook (D1).
5. Hang the crystal drop (E) on the hook (E1).
6. Hang the crystal drop (F) on the hook (F1).
7. Hang the crystal drop (G) on the hook (G1) & (G2).
8. Hang the crystal drops (H) on the hook (H1).
9. Hang the crystal drops (I) on the hook (I1).
10.  Hang the crystal drops (J) on the hook (J1).
11.  Hang the crystal drops (K) on the hook (K1).
12. Hang the crystal drops (L) on the hook (L1).
13. Hang the crystal drops (M) on the hook (M1).

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>