URANT U10 Wireless Router Installation Guide

June 4, 2024
URANT

URANT U10 Wireless Router

URANT U10 Wireless Router
PRODUCT

Product Overview

The Urant Wireless Router is connected to your router wirelessly, strengthening its signal and expanding its coverage into areas that could not otherwise be reached. The device also reduces Signal interference to ensure reliable wi-Fi coverage throughout your home or office. Easy Installation & Quick Position. The extender works with any standard wireless router. Follow the Quick Setup instructions on the extender’s web management page. Once the extender is connected to a router, you can relocate it to your preferred location with no further configuration required. The intelligent signal light can help to find the best location.

Appearance

LED Explanation

URANT U10 Wireless Router FIG 2

Port and Button Description

URANT U10 Wireless Router FIG 2

Repeater Mode

Power On
Plug the Repeater into an electrical outlet next to your host router, and then wait until the 2.4G wireless and 5G wireless LED is on.URANT U10 Wireless
Router FIG 4

Set-UpURANT U10 Wireless Router FIG 5

Connect to the extended network and enjoy internet. The extended network shares the same wireless password as that of your host network, but may have different network name if you have customized the SSID during the configuration.
Note:Since the performance of the extended network will be affected by the distance between extender and host router, we highly recommend you to relocate your extender referring to Position Your Extender. ****

Position Your Extender

Please follow the instructions below to achieve optimal performance of the extender.

  1. Plug the extender into an electrical outlet between your host router and the Wi-Fi “dead” zone.
    The location you choose must be within the range of your existing host network.

  2. Wait until the LEDs are lit.Make sure the extender is in a location with 2 or more LEDs lit. If not, relocate tcloser to the router to achieve better signal quality.URANT U10 Wireless Router FIG 7

Router Mode

URANT U10 Wireless Router FIG 8 URANT U10
Wireless Router FIG 9 URANT U10
Wireless Router FIG 10 URANT U10
Wireless Router FIG 11

  1. If you choose Dynamic IP,Dynamic IP users are usually equipped with a cable TV or fiber cable.

  2. If you choose Static IP,enter the information provided by your ISPin the corresponding fields. URANT U10 Wireless Router FIG 12

  3. If you choose PPPoE,enter the username and password provided by your ISP. PPPoE users usuafiy have DSL cable modems.URANT U10 Wireless Router FIG 13

AP Mode

URANT U10 Wireless Router FIG 14 URANT U10
Wireless Router FIG 15

Frequently Asked Questions (FAQ)

  1. What can I do if the login window does not appear?
    If the computer is set to a static or fixed IP address, change the setting to obtain an IP address automatically.
    Verify if http://192.168.168.1 is correctly entered l in the web browser.
    Make sure your computer is connected to the Mini Router’s network.
    Use another web browser and try again.
    Reboot your router and try again.
    Disable the network adapter used currently and then enable it again.

  2. What can I do if l cannot access the lnternet?
    Check if the internet is working properly by connecting a computer directly to the modem via Ethernet cable. If not,
    connect your internet provider.
    Reboot your router and try again.

  3. How do I restore the router to its factory default setting?
    While the router is powered on, press and hold the reset button on the rear panel of the router for approximately 5 seconds.

  4. Why set the repeater mode is unsuccessfully?
    You may have typed in the router’s wireless password incorrectly, please log in and check the wireless password.
    The Mini router may be out of range, please move it closer to the router.
    Please reset the Mini Router and go through the configuration again.
    A.lf you need reset the extender. You need press and hold the reset button inside the tiny hole for 10 seconds.

FCC Rules

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by tuming the equipment offand on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radioTV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals