ALPINE iLX-F259 9 Inch Halo9 Mech Less Audio Video Receiver Installation Guide
- June 13, 2024
- Alpine
Table of Contents
ALPINE iLX-F259 9 Inch Halo9 Mech Less Audio Video Receiver
Product Information
The iLX-F259 is a 9-inch Halo9 Mech-Less Audio/Video Receiver with Apple CarPlay and Android Auto. It is designed to enhance your in-car entertainment experience by providing seamless integration with your mobile devices. This firmware update (version iLX-F259_2.0.2) addresses several issues and improves the functionality of the device. The update includes the following enhancements:
- CarPlay and Android Auto volume range can now be set from 0-35.
- Dimmer setting is defaulted to Auto.
- Answer/hang up steering wheel controls are added to CarPlay and Android Auto.
- Improved FLAC playback through USB.
Please note that it is important to follow the update procedure carefully to avoid any potential damage to the head unit.
Introduction
- This installation manual is designed to take you through the step-by-step installation of the firmware version iLX-F259_2.0.2 (2019.04.11) update of the iLX-F259. Please familiarize yourself with the owners manual (found at www.alpine-usa.com/support) and if you still have additional questions please call 1-800-TECH-101.
- This firmware update corrects issues with the following:
- CarPlay and Android Auto volume range can now be set 0-35
- Dimmer setting is default to Auto
- Adds answer/hang up steering wheel controls to CarPlay and Android Auto
- Improved FLAC playback through USB
Caution
- Do NOT turn off vehicle’s ignition or head unit’s power switch while updating. Some modern vehicles may shut down the ignition (ACC) if the engine is not running for some time. If you are not sure if this applies to your car, leave the engine running while the update is in progress.
- Do NOT remove the USB flash memory while updating.
- Do NOT press any buttons while updating.
- Do NOT update while driving.
- Failing to follow any of these cautions could cause damage to the head unit.
HOW TO USE
- Step 1: Format The Flash Drive
- Only flash drives formatted to FAT32 can be read by the head unit. This means that your flash drive can not be formatted to anything else including NTFS, exFAT, etc.
- In Windows the drive can be formatted by right clicking on the drive in file explorer and selecting format as shown in the pictures below.
- Step 2: Copy The Audio Update Files To The Flash Drive
- Extract the downloaded files using a program like WinZip to your computer. If you don’t have a program that handles zip files on your computer you will need to install one.
- Once extracted you will see a folder named ILX-F259. Copy the unzipped folder to your flash drive by copy and pasting or dragging and dropping the file. The pictures below show the folder ILX-F259 on the flash drive and the folders in it.
Note: You can NOT change the file names or folder names. The head unit will not recognize the files if you do. DO NOT just copy the files to the drive. You need to copy the folder.
Notes:
* Do NOT store any other files on the flash drive. If there is anything on the drive besides the update folder it will not read correctly.
* Certain manufacturer’s USB memory may not work. If so, try a different manufacturer’s USB memory.- Step 3: Copy The Update Files To The Head Unit
- Plug the flash drive into the USB connector of the head unit. The USB extension is typically ran from the back of the head unit to either the glove box or center console areas of the vehicle depending on the original installation.
- Turn on the vehicle’s ignition to power on the head unit. Do NOT turn off the igntion or the power of the head unit while the system is updating!
- The update popup will automatically run. Select Yes.
- The unit will reboot and begin the update. When the update is finished the head unit will reboot again.
- Check version iLX-F259_2.0.2 (2019.04.11) SETTINGS/GENERAL/ABOUT/VERSION INFORMATION. Then do a factory reset. SETTINGS/GENERAL/ABOUT/RESTORE FACTORY SETTING.
Troubleshooting Guide
| Symptom | Possible Cause | Remedy |
|---|---|---|
| 1 | Head unit will not read flash memory. | The downloaded software was not |
| unzipped. | Refer to Step 2. The .zip file will need to be unzipped first using |
your program of choice (for example, WinZip, WinRAR, Izarc, etc).
There are other files on the flash drive.| The flash drive should be freshly
formatted (refer to Step 1) and the only files on it should be the downloaded
files as shown in Step 2.
The file folder name was changed or put into a different folder.| Make sure
only the file that is shown in step 2 is copied over.
The USB port was installed incorrectly.| Make sure the port is working
correctly by plugging in an iPod or flash memory with a few MP3’s on it and
seeing if it will play the music. If that’s not working then there’s no way
for the update to work. Try plugging the flash drive directly into the tuner
without the extension cable.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>