STARK HY-6109S Solar Outdoor Wireless Acousto Optic Siren Instruction Manual
- June 13, 2024
- STARK
Table of Contents
OPERATING
MANUAL
STARK
Solar Outdoor Wireless Acousto-optic Siren ST-6109S
- This product is a networking accessory that needs to be used with the company’s gateway
Solar Outdoor Wireless Acousto-optic Siren User’s Manual
Brief Introduction
The solar outdoor wireless acousto-optic siren {hereafter called siren) adopts
8 bit MCU technology, built-in 8 LED lights, 2 105dB buzzers and 1 built-in
lithium battery. Using solar energy to charge, without external power supply.
It is an entire wireless system. The siren not only can connect with the
alarm host via wireless transmission, but also can be used as an alarm host
and a repeater. It is widely used in banks, shops and villas etc.
When the siren works with wireless alarm host by wireless transmission, alarm
host can input the siren’s address, or directly learning with the siren. The
siren’s tamper alarm, AC information, battery voltage information are all
transmitted to the alarm host via wireless signal. Then the alarm host
notifies the user about the alarm information via SMS, center and voice .
The siren also can indicate alarm host arm I disarm status.
Users can buy the relative remote controls and detectors according to their
demand when the siren is used as the alarm host. It can connect with these
wireless accessories and become a powerful independent alarm system.
The siren can also be used as a repeater, which can increase the wireless
launch distance effectively.
Main Features
- Used as a repeater, it can transmit 16 wireless accessories.
- 3 colors of indicator lights flashing modes. ( Red/ Bluel Red+Blue )
- Design for preventing the siren being removed maliciously .
- Acousto-optic notice when operating Arm /Disarm.
- Status reports including the alarm from siren itself, tamper alarm
- Support 8 remote controls, 16 detectors. The last 4 wireless zones for 24 hours defend.
- Two optional ways to enroll: by trigger button or inputting siren address code.
- 105dB alarm sound, flashing lights, a strong deterrent.
- Built-in 5200mAh 3.7V 18650 lithium battery, up to 120days of stand-by time.
- Built-in balance device, convenient to install in horizontal direction.
Interface definition
Operation Instruction
4.1.Remote Control
4.1.1. Enroll Remote Control
Step1: Under the normal status without alarm event, long press “SET” button
with 3s until heard a short “Di” and red indicator light bright, it means the
siren is in enrolling status, then user can start to enroll remote control,
press any button of remote control to enroll.
Step2: If user wants to enroll the next remote control, please press “NEXT”
button to the next one.
Attention: If the red indicator light is flashing, it means the current remote
control has not been enrolled and user can press any button of remote control
to enroll. If enrollment succeeded, the siren will prompt a short “Di”,
meanwhile red indicator light will turn flashing into long bright, it means
remote control enrollment succeed. If the red indicator light is long bright,
it means the current address has been already enrolled. User should delete
previous one to re- enrolling. If heard 5 short “Di”, it means the remote
control has already been enrolled.
4.1.2. Delete Remote Control
In remote control enrolling status, press “NEXT” button with 3s to delete the
existing remote control. After user heard 2 short “Di” from siren and the
indicator turned long bright into flashing, deletion is successful.
4.1.3. Exit Remote Control Enrollment
In remote control enrolling status, short press “SET” button twice to exit.
4.2.Detector
4.2.1.Enroll Detector
Step 1: Under remote controller enrolling status, short press “SET” button
once, blue indicator light bright, it means the siren is in enrolling status,
then user can start to enroll detectors.
Step2: If user wants to enroll the next detector, please short press “NEX ”
button to the 2″‘ detector.
Attention: If the current blue indicator light is flashing, it means the
current detector has not yet been enrolled and user can enable T detector to
transmit alarm signal to be enrolled. If enrollment succeeded, siren will
prompt a short “Di”, meanwhile blue indicator light will tum flashing into
long bright, it means successful enrollment of detector. If the current blue
indicator light is long bright, it means the current detector has been already
enrolled. User should delete previous one before re-enrolling. If heard 5
short “Di”, it means the detector has already been enrolled.
4.2.2.Delete Detector
In detector enrolling status, press “NEX” button with 3s to delete the
existing detector. After user heard 2 short “Di” and the blue indicator light
turned long bright into flashing, deletion is successful.
4.2.3. Exit Detector Enrollment
In detector enrolling status, short press “SET’ button once to exit.
4.3. Arm/Disarming Prompt Voice
4.3.1 Entering Arm/Disarming Prompt Voice status
Under the “Detector Enrollment Status”, short press “SET” button once, the
alarm enters the setting status of “Arm/Disarming Prompt Voice”, and the red
and blue indicator lighing. Short press “NEXT” to set.When the indicator is
lighting ON(not flashing), ii means the “Arm/Disarming Prompt Voice” with “LED
indication” is activated; When the indicator light is slow flashing, it means
the “Arm/Disarming Prompt Voice” (but without “LED indication”) is activated;
When the indicator light is fast flashing; it means the “Arm/Disarming Prompt
Voice” and “LED indication” is totally disabled. It means arm/disarm when red
light flashes.has light indicator remind, no sound remind 4.3.2 Exit
“Arm/Disarming Prompt Voice” setting mode.
Under the “Arm/Disarming Prompt Voice” setting mode status, short press “SET”
button twice,
4.4. LED indication setting in Armed status
4.4.1 Entering LED indication setting in Armed status
Under the “Arm/Disarming Prompt Voice Status”, short press “SET” button once,
the alarm enters the setting status of “LED indication setting in Armed
status”, and the red indicator lighing. Short press “NEXT” to set.When the
indicator is lighting ON(not flashing), it means the “LED indication setting
in Armed status” is activated (in Armed status the LED flash 1 times/5
seconds);When the indicator light is fast flashing, it means the “LED
indication setting in Armed status” is disabled.
4.4.2 Exit “LED indication setting in Armed status” setting mode.
Under the “LED indication setting in Armed status” mode status, short press
“SET” button once.
4.5.Enroll Siren
Under siren standby status, short press “ENROLL” button once, siren will emit
wireless enrolled signal to host, then alarm host enter siren enrolled status,
when user hear a short “Di” from alarm host, it means siren enrollment
succeed.
4.6. Repeater
4.6.1.Enroll Repeater
Step1: Long pressing “SET” and “NEXT’ buttons for 3 seconds at the same time,
after hearing a short “Di”, the siren enters the repeater enrollment. The red
and blue indicator light bright refers to the current repeater which need be
transmitted is enrolled.
Step2: If user wants to enroll the next one, please short press “NEXT’ button
to the 2″‘ repeater.
Attention: If the current red and blue indicator light is flashing, it means
the current repeater has not yet been enrolled and user can trigger the
repeater. If enrollment succeeded, siren will prompt a short “Di”, meanwhile
red and blue indicator light will turn flashing into long bright, it means
successful enrollment of repeater. If the red and blue indicator light is long
bright, it means the current repeater has been already enrolled. User should
delete previous one before re-enrolling. If heard 5 short “Di”, it means the
repeater has already been enrolled.
4.6.2.Delete Repeater
In repeater enrolling status, press “NEXT” button with 3s to delete the
existing repeater. After user heard 2 short “Di” and the blue indicator light
turned long bright into flashing, deletion is successful.
4.6.3.Exlt Repeater Enrollment
In repeater enrolling status, short press “SET’ button once to exit.
4.7. Copy the siren address
4.7.1. Copy the siren address
Press the “ENROLL” and “NEXT” keys for 3 seconds at the same time, hear the
one short “beep” , enter the copy alarm address status, and red and blue light
of siren is on. If the red and blue indicator is flashing, it means the
factory address. Then long press the “ENROLL” button , short press “ENROLL”
button of the siren which you want to copy; if the copy is successful, the
alarm will prompt one short “Beep”, while the alarm red and blue indicator
will stop flashing into a long light, suggesting that the transponder
replication is successful; if the alarm red and blue indicator is long bright,
indicating that the current address of the siren has been copied, the user
must deleting first and then you can re- copy.
4. 7 .2. Delete the copy siren address
Press the “NEXT” key for 3 seconds to clear the copy address of siren and
return to the factory address, and will prompt the two short “beep” and the
siren red and blue indicator changes from long bright to Flash, indicate
delete success.
4.7.3. Exit the copy siren address
In the copy siren address state, short press “SET” key , will exit the copy
siren address state.
4.8. Recovery Factory Default
In stand-by status, long press “SET’ and “ENROLL”, until hear 2 short “Di”, It
means that the siren has been back to factory default.
Technical parameter
Size specification: 320mm • 210mm • 114mm •(length• width• thickness) Battery:
3.7V 5200mAh 18650 lithium battery
Alarm current: ,s;;4oomA Stand-by time: ,s;;120 days (without sunlight) Siren
alarm sound: 105dB
Wireless Working Frequency: 433.92MHz Use environment: working temperature
-20-C-+55-C relative humidity 40 -80%
Wireless Emitting Distance: ,s;;400 ( in the open area)
Wireless Receiving Distance: ,s;;350 (in the open area)
6109S user manual V1 .1
2021.12.20
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>