Origin 21 W3005SMB 36 In to 72 In Brushed Nickel Iron Single Curtain Rod with Finials Instruction Manual
- June 13, 2024
- Origin 21
Table of Contents
Origin 21 W3005SMB 36 In to 72 In Brushed Nickel Iron Single Curtain Rod with Finials
Important Information
Thank you for purchasing this ORIGIN 21 product. We’ve created these easy-to- follow instructions to ensure you spend your time enjoying the product instead of putting it together. if you need more information than what is provided here, please visit Lowes.com, search the item number and refer to the Guides & Documents tab on the product’s page.
If the item is no longer for sale, or if you have any questions or problems, please call our customer service department at 888-251-1026, 8 a.m. – 8 p.m. EST, Monday – Sunday. You could also contact us at ascs@lowes.com
PREPARATION
Before beginning installation of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble or install the product.
Estimated Assembly Time: 15 minutes.
TOOLS REQUIRED
CARE AND MAINTENANCE
Dust gently with dry cloth.
Periodically check to make sure all components are properly positioned, free
from damage and firmly connected.
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble or install the product.
FEELING CONFIDENT? START YOUR NEXT PROJECT¿
- Visit lowes.com for more information.
TROUBLESHOOTING
| PROBLEM | POSSIBLE CAUSE | CORRECTIVE ACTION |
|---|---|---|
| Cannot access the top screw hole on brackets to install properly. | Supporting | |
| bracket arm is in the way. | Swivel the arm to the side and install the top |
screw hole BEFORE swiveling the bracket arm back to original position and
installing the bottom screw hole.
Rod does not extend to desired length / Rod is too short for desired length.|
Only two rods were used, and the third larger diameter rod was not applied.|
Add the third larger diameter rod to form a longer 3-piece telescopic rod (see
step 4).
Rod is too long for desired length.| Three rods were all used, but only two
rods are needed.| Discard one larger diameter rod and install just the 2-piece
telescopic rod (see step 4).
Rods slide / slip when curtain panels are pulled left and right.| The rods are
not properly secured in the brackets.| Tighten the rod-securing-screws on the
brackets (see step 6).
PACKAGE CONTENTS
-
(preassembled)
-
(1 preassembled) x 2
-
x 1
(preassembled)
HARDWARE CONTENTS
Note: Hardware shown actual size.
INSTALLATION OVERVIEW
Remove preassembled finial [A] from inner rod [C] (keep the other finial attached).
Before proceeding, swivel angled supporting arm away so both bracket screw holes are accessible. Use bracket [AA] as a guide to mark desired locations on wall for mounting screws. Use level to ensure screw holes alignment.
Stud installation is recommended, use a stud finder to locate stud. If no
studs are present, provided drywall anchors can be used.
For wood/stud installations , anchors [CC] are not required. Pre drill 3/32” pilot holes at marked locations
For drywall/paneling installations , anchors [CC] are required. Predrill 1/4” pilot holes at market locations, then screw anchors [CC] into pilot holes.
Place bracket [AA] on pilot holes/anchors, then fasten screw [BB] into the top pilot hole/anchor first. Swivel angled supporting arm back to original position to overlap and align with bottom screw hole, and fasten second screw [BB] into pilot hole/anchor to complete bracket [AA] installation.
Fasten the other finial [A] into rod. Place entire rod and drapery panel set onto installed brackets [AA] and make sure center bracket [AA] sits between two drapery panels.
For installation rod length wider than 49” (for 36”-72” rod set) or 96” (for 72”-144” rod set), attach additional outer rod [B] to the end of inner rod [C] (this is NOT needed for installation rod length shorter than 49”). Attach both drapery panels (sold separately) to assembled rod set; make sure space is available between two panels for center bracket [AA].
Tighten the preassembled screws on mounting brackets [AA] to lock the rod
assembly in place.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>