Origin 21 W3003SMB Brushed Nickel Iron Single Curtain Rod with Finials Instruction Manual

Origin 21 W3003SMB Brushed Nickel Iron Single Curtain Rod with Finials

Product Information

• Product Name: Drapery Rod Set
• Model Numbers: #W3003SMB, #W3003LMB, #W3003SBN, #W3003LBN
• Estimated Assembly Time: 15 minutes
• Tools Required: None mentioned
• Care and Maintenance: Read and understand the entire manual before assembly or installation
• Manufacturer: ORIGIN 21
• Contact Information: Customer service department at 888-251-1026, 8 a.m. – 8 p.m. EST, Monday – Sunday or ascs@lowes.com
• Printed in: Vietnam

Product Usage Instructions

1. Before starting assembly or installation, read and understand the entire manual.
2. If you need more information or additional guides, visit Lowes.com, search the item number, and refer to the Guides & Documents tab on the product’s page.
3. If the item is no longer for sale or if you have any questions or problems, contact the customer service department at the provided phone number or email address.
4. Check the package contents to ensure you have all the necessary components.
5. Remove the preassembled finial [A] from the inner rod [C], keeping the other finial attached.
6. Unscrew the preassembled screws on all brackets [AA] and slide the preassembled one out of rod [B].
7. If needed, fasten the other finial to the rod end.

Thank you for purchasing this ORIGIN 21 product. We’ve created these easy-to- follow instructions to ensure you spend your time enjoying the product instead of putting it together. if you need more information than what is provided here, please visit Lowes.com, search the item number and refer to the Guides & Documents tab on the product’s page.

TROUBLESHOOTING

PROBLEM

Cannot access the top screw hole on brackets to install properly.

| Supporting bracket arm is in the way.| Swivel the arm to the side and install the top screw hole BEFORE swiveling the bracket arm back to original position and installing the bottom screw hole.

Rod does not extend to desired length / Rod is too short for desired length.| Only two rods were used, and the third larger diameter rod was not applied.| Add the third larger diameter rod to form a longer 3-piece telescopic rod (see step 4).

Rod is too long for desired length.| Three rods were all used, but only two rods are needed.

| Discard one larger diameter rod and install just the 2-piece telescopic rod (see step 4).
Rods slide / slip when curtain panels are pulled left and right.| The rods are not properly secured in the brackets.| Tighten the rod-securing-screws on the brackets (see step 6).

PREPARATION

Before beginning installation of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble or install the product.

Estimated Assembly Time: 15 minutes.

TOOLS REQUIRED

CARE AND MAINTENANCE

Dust gently with dry cloth.
Periodically check to make sure all components are properly positioned, free from damage and firmly connected

SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble or install the product.

FEELING CONFIDENT? START YOUR NEXT PROJECT

Visit lowes.com for more information.

PACKAGE CONTENTS

HARDWARE CONTENTS

note: Hardware shown actual size.

INSTALLATION OVERVIEW

Remove preassembled finial [A] from inner rod [C] (keep the other finial attached). Unscrew preassembled screws on all brackets [AA] and slide the preassembled one out of rod [B].

Please note the removed screws will be used later, so please keep them within sight.

Arrange brackets placement according to rod lengths: For installation rod length shorter than 49” (for 72”-144” rod set) or 96” (for 72”-144” rod set), the smaller bracket [BB] (marked “S” in the back) has to be placed one of the side to hold the inner rod [C]. For installation rod length longer than 49” (for 72”-144” rod set) or 96” (for 72”-144” rod set), the smaller bracket [BB] has to be placed in the center between the two larger brackets [AA] (marked “L” in the back”).

For wood/stud installations, anchors [DD] are not required. Pre drill 3/32” pilot holes at market locations.

For drywall/paneling installations, anchors [DD] are required. Predrill 1/4” pilot holes at market locations, then screw anchors [DD] into pilot holes.

For installation rod length shorter than 49” (for 36”-72” rod set) or 96” (for 72”-144” rod set), The additional outer rod is NOT needed. Make sure the inner rod [C] relative to the outer rod [B] is the same as the position of the smaller bracket [BB] relative to the larger brackets [AA]. Attach drapery panel (sold separately) to rods, and place entire set onto installed brackets [AA&BB].

For installation rod length wider than 49” (for 72”-144” rod set) or 96” (for 72”-144” rod set), attach additional outer rod [B] to the end of inner rod [C]. Attach drapery panel (sold separately) to rods, and place entire set onto installed brackets [AA&BB].

Fast the other finial to rod end.

Tighten the preassembled screws on mounting brackets [AA] lock the rod assembly in place.

ORIGIN 21 and logo design are trademarks or registered trademarks of LF, LLC. All rights reserved.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>