Origin 21 M-Print PRO Brushed Gold Iron Single Curtain Rod Instruction Manual
- June 13, 2024
- Origin 21
Table of Contents
Origin 21 M-Print PRO Brushed Gold Iron Single Curtain Rod
Product Information
- Product Name: Drapery Rod Set
- Model Numbers: #W3004SMB, #W3004LMB, #W3004SBN, #W3004LBN, #W3004SBG, #W3004LBG, #W3004SBGW, #W3004LBGW
- Estimated Assembly Time: 15 minutes
- Tools Required: None
- Manufacturer: ORIGIN 21
- Contact Information: Customer Service Department at 888-251-1026 (8 a.m. – 8 p.m. EST, Monday – Sunday) or ascs@lowes.com
- Printed in: Vietnam
Product Usage Instructions
- Read and understand the entire manual before attempting to assemble or install the product.
- Remove the finials [A] from rods [B&C].
- Loosen the preassembled screws on bracket [AA] and slide the bracket [AA] away from rod [B]. Keep the outer rod [B] and inner rod [C] assembled and do not separate them.
- If the rod does not extend to the desired length or is too short for the desired length, refer to the instructions marked with “*” for proper rod length adjustment.
- Fasten the finials to the rod ends.
- Tighten the preassembled screws on the mounting brackets [AA] to lock the rod assembly in place.
Thank you for purchasing this ORIGIN 21 product. We’ve created these easy-to-
follow instructions to ensure you spend your time enjoying the product instead
of putting it together. if you need more information than what is provided
here, please visit Lowes.com, search the item number and refer to the Guides &
Documents tab on the product’s page.
If the item is no longer for sale, or if you have any questions or problems,
please call our customer service department at
888-251-1026, 8 a.m. – 8 p.m.
EST, Monday – Sunday. You could also contact us at
ascs@lowes.com
TROUBLESHOOTING
| PROBLEM | POSSIBLE CAUSE | CORRECTIVE ACTION |
|---|---|---|
| Cannot access the top screw hole on brackets to install properly. | Supporting | |
| bracket arm is in the way. | Swivel the arm to the side and install the top |
screw hole BEFORE swiveling the bracket arm back to original position and
installing the bottom screw hole.
Rod does not extend to desired length / Rod is too short for desired length..|
Only two rods were used, and the third larger diameter rod was not applied.|
Add the third larger diameter rod to form a longer 3-piece telescopic rod (see
step 4).
Rod is too long for desired length.| Three rods were all used, but only two
rods are needed.
| Discard one larger diameter rod and install just the 2-piece telescopic rod
(see step 4).
Rods slide / slip when curtain panels are pulled left and right.| The rods are
not properly secured in the brackets.| Tighten the rod-securing-screws on the
brackets (see step 6).
PREPARATION
Before beginning installation of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble or install the product.
Estimated Assembly Time: 15 minutes.
TOOLS REQUIRED
CARE AND MAINTENANCE
Dust gently with dry cloth.
Periodically check to make sure all components are properly positioned, free
from damage and firmly connected.
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble or
install the product.
FEELING CONFIDENT? START YOUR NEXT PROJECT
- Visit lowes.com for more information.
PACKAGE CONTENTS
HARDWARE CONTENTS
Note: Hardware shown actual size.
INSTALLATION OVERVIEW
Remove finials [A] from rods [B&C]. Loosen preassembled screws on bracket [AA] and slide bracket [AA] away from rod [B]. Keep outer rod [B] and inner rod [C] assembled and do not separate them.
Use bracket [AA] as a guide to mark desired locations on wall for mountain
screws. Use level to ensure screw holes alignment.
Stud installation is recommended, use a stud finder to locate stud. If no
studs are present, provided drywall anchors can be used.
For wood/stud installations, anchors [CC] are not required. Pre drill 3/32” pilot holes at marked locations.
For drywall/paneling installations, anchors [CC] are required. Predrill 1/4” pilot holes at marked locations, then screw anchors [CC] into pilot holes
For installation rod length shorter than 49” (for 36”-72” rod set) or 96” (for
72”-144” rod set), only ONE outer rod [B] is needed. Feed both rods [B&C]
through one bracket [AA] with inner rod [C] in front. Attach one drapery panel
(sold separately) onto rods. Next, continue to feed both rods [B&C] into
center bracket [AA] and attach another drapery panel onto rods. Finally,
extend inner rod [C] and feed through last bracket [AA].
For installation rod length wider than 49” (for 36”-72” rod set) or 96” (for
72”-144” rod set), feed both rods [B&C] through one bracket [AA] with inner
rod [C] in front. Attach one drapery panel (sold separately) onto rods. Next,
extend inner rod [C] through center bracket [AA] and assemble the other outer
rod [B] with by sliding it over inner rod [C]. Finally, attached another
drapery panel onto rods and feed last outer rod [C] into last bracket [AA].
Fasten finials to rod ends.
Tighten preassembled screws on mounting brackets [AA] to lock rod assembly in place.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>