GE L60C-2F-D022 Random Sparkle 4 Marker Multicolor Light Bulb Christmas Pathway Markers Instruction Manual

GE L60C-2F-D022 Random Sparkle 4 Marker Multicolor Light Bulb Christmas

Pathway Markers

IMPORTANT SAFETY INSTRUCTIONS

When using electrical products, basic precautions should always be folowed incuding the folowing.

• READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
• Do notuse seasonal produds outbors unless maker suithle forindbor and outdoor use. When producls are used in outdo apicaions, conect the product to a Ground Fault Circuit Interuptina (GFCI outlet. If one is not provided, contact a qualifed electician for oroper installation.
• This seasonal use oroductis not intended for permanent instal ation or use.
• Do no mountarplacenear gas or electric heales, freplaces, candes or ohe simlar sources o heat.
• Do not secure the wino ofhe oroduct with staples or nais. or place on sharp hooks or nails.
• Do notlet lamps rest on the supply cord or on any wire.
• Unoluo the product when leaving the house, when retinno for the night, or if etr unattended.
• This is an etectic product not a toy!. To avoid risk of fire, bums, personal injur and electric shock it should not he daved with or olaced where small children can reach it.
• Do not use this product for other than its intended use.
• Do nothang onaments o oher objects from cod, wire, a light sting.
• Do not cose doos or windous on tre noduct oretension coris as his may damane the vie insultion.
• Do not cover the product with cloth, paper or any material not part of the productwhen in use.
• This poductis equiped with push-in type LED lamps. Do not wist lamps.
• This productempoys overload prodecion (fuse). A down fuse indicates an overload or short-orcuit situation. I the fuse bows, unplug the product rom the outet. so unplug any acadrona stings or producd inat may be attached to the product
• Replacethe fuse as per the user senwang instucions folow product marking for poperts rang) and check he podid. the centenant se bous a shotsicut na, de pesent and te podut shoud be dsadet.
• Read and folow al instructions that are on the productor provided with the product.
• SAVE THESE INSTRUCTIONS

CAUTION:
To reduce the rick of fre and electric shock: al Do not install on trees havino needles, leaves or branch coverngs of meta or maternals which look like mela. b) Do no mount on support strings in manner that can cut or damage wire insulaton.

USE AND CARE INSTRUCTIONS

• Whenthe productis placed on lie a tree, he tee shouid be wel maintained and fresh. Do not place on hie tees in which the needles a brown or beak of easily.
• Keep the tree holder fled with water.
• It the poductis placed on ate, the tre should be wel secured and stable.
• Belie wing or eusing inspect nodud caetly, Discadam poduds bed hare ol, damaget, ortaged wie insuladonor ords, acadksitte lamphodes or enclosures, lose connections, or exposed copper wire.
• Belue sling the product, carefuly emone he product fom wherenertis placed, ndluding tres branches, or bushes to avoid anyundue stain or stress onthe product conduciors, connectons, and wires.
• When notin use, sloe neaty in a cod, dy location polected fom sunlight.
• The LED lamp has polanty, Do not deliberdely change the diection o the LED lamp in the lamphober.

USER SERVICING INSTRUCTIONS

To replace the fuse:

• Gasp plug and renove from the receptacle or ohe oulet derice. Do nat umplug by puling on cord.
• Opentise cover. Side openfise access cover on top of atachmentplug towards blades.
• Remove fuse carefuly. Tum plug over to remove fuse.
• RISK OF FIRE. Replace fuse only with 3Amp, 125 Volt fuse provided with product.
• Close fuse cover. Side closed the fuse access cover on top of atachment olug.
• RISK OF FIRE. Do not replace attachmentplug. Contains a safety device fuse) that should not be removed. Discard product if the attachment plug is damaged.

TO reolace a lamo:

• Grasp plug and remove from the receptacle or other outet device. Do not unplug by pulling on cord.

• Be sure to pul lamp and plastic base straicht out of lampholder.

• Replace lamp with only 2.4 volts, 0.048 watts or 3-6 vots, 0.072 watts LED type lamps provided with this product. lithe new lamp base does not it in lamp hoder, olow the step below before Step c. NOTE- Be carelid when exchanging the lamp base on the new lamp with the old one or the LED wires may break it leads are bent too many times.

  1. Remove the base or bumed out LED lamp by carefull straightening lamp leads and gently puli lamp out.
  2. Thread leads of new LED lamp through holes in old base with one lead in each hole.
  3. Afterlamp is fulyinseted int base, bend each lead up, ike other LED lamps in the lightset so that the leads wil ouch the conlacds inside the lamp holder.

• NOTE – To avoid damage to the set

  1. Do not deliberately change the direction of the LED lamp in the lampholder.
  2. Use only included spare LED bulbs for replacements, and only replace with the same color bulbs.
  3. Do not switch the order of the colors of the buts or interchange bulbs from diferent sets.

CAUTION’

1.  Risk offire. This product does not contain lamp shunts, which alw the product to operate ifone lamp bums out. Replace lamps only with the spare lamps provided with this oroduct.
2. To reduce the risk of overheating, replace bumed-out lamps promptly. Use 2.4 volts, 0. 048 watts or 3.6 volis, 0.072 watts only.
3. This is an electric product – not a toy! To avoid risk of fire, burns, personalinjury and electric shock it should not be played with or placed where small chilren can reach it
4. DO NOT OPERATE WHEN THE BULBS ARE ABSENT FROM THE SOCKETS. MISSING BULBS MUST BE REPLACED PROMPTLY.

Connecting Sets End to End:

1. When mutple products are connected together, do not exceed the lowest of the indicated maximum wattage on the cord tag near the connected products receptace.
2. Do notoverbad. Connectother Lighting Strings or decorative outfis end-o-end up to a maximum of216 Wats (1.8Amps) total.
3. If connecting to a lighting string that does nothave a wattage (W rating, Calculate the watage M as folows.
   • Multiply the marked curent (A) which may be on a flag type label near the plug. by 120.
   • Then add the wattage ofeach light sting together for a total of 216 Wats or less. (Do not exceed 216 Wats.)
   • For questions and or assistance, call customer service at 1-877-398-7337 orvist us on the web at www.GEholidaylighting.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>