JUNO JCLR6L Downlight Retrofit Kit Instruction Manual
- June 13, 2024
- Juno
Table of Contents
JUNO JCLR6L Downlight Retrofit Kit
SAFETY WARNINGS
WARNING: For your safety, read and understand instructions completely before starting installation. Before wiring to power supply, turn off electricity at the fuse or circuit breaker box.
NOTE: Juno recessed products are designed to meet the latest NEC requirements and are classified in compliance with applicable UL standards. Before attempting installation of any recessed lighting product, check your local electrical building code. This code sets the wiring standards and installation requirements for your locality and should be understood before starting work.
SAVE THESE INSTRUCTIONS
Product Information
Juno’s JCLR6 and JCLR8 LED trims may be used as retrofit trims for 6″ and 8″
incandescent, CFL or H.I.D open frame rough-in sections. Suitable for damp
locations.
The JCLR6 and JCLR8 Retrofit trims consist of the following: Reflector, Optic
Lens Assembly, Trim Ring, LED Driver/Driver Junction Box, Conduit Whip
Assembly, Conduit Fitting, Qty 6 Friction Clips and installation instructions
(In hardware bag). Check for all contents prior to installation (Refer to
Figure 1).
Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
WARNING – Risk of fire or electric shock.
- Installation of this retrofit assembly requires a person familiar with the construction and operation of the luminaire’s electrical system and the hazard involved. If not qualified, do not attempt installation. Contact qualified electrician.
- Install this kit only in luminaires that have the construction features and dimensions described in these instructions, and where the input rating of the retrofit kit does not exceed the input rating of the luminaire.
WARNING – To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
IMPORTANT – Trims must be grounded as outlined below. Failure to do so can result in electric shock or undesired operation. The trim assembly must be electrically grounded either through the conduit whip/junction box connection or through the friction clips contact with rough-in section. This requires that the rough-in section junction box be electrically grounded.
To use this product in an ungrounded rough-in section, consult factory for additional instructions.
IMPORTANT – Power to the luminaires must be turned off prior to installing these LED retrofit trims. Failure to do so can cause electric shock, which can result in injury or death.
THIS RETROFIT KIT IS ACCEPTED AS A COMPONENT OF A LUMINAIRE WHERE THE SUITABILITY OF THE COMBINATION SHALL BE DETERMINED BY CSA OR AUTHORITIES HAVING JURISDICTION.
Dimming
- Universal input voltage (120VAC thru 277VAC) and 347VAC. Retrofit dimmable with the use of most 0-10V wall box dimmers.
- 120VAC input voltage. Retrofit dimmable with the use of most incandescent, magnetic low voltage or electronic low voltage* wall box dimmers.
Consult Juno Product Services or website for compatibility.
*Electronic low voltage dimmers require a neutral wire connection in the wall box.
Juno JCLR6 and JCLR8 Retrofit LED Trim Compatibility
Commercial Rough-In Section Compatibility
The JCLR6 and JCLR8 retrofit trims are provided with spring steel friction clips allowing for installation in a variety of 6” and 8” commercial recessed open frame rough-in sections with a ceiling thickness ranging from 1/2″ to 1 1/8″:
Rough-in section inside diameter compatibility range:
JCLR6S: 6″ – 6 1/2″, JCLR6L: 6 5/8″ – 7 1/8″.
JCLR8S: 7 13/16″ – 8 5/16″, JCLR8L: 8 5/8″ – 9 1/8″.
Rough-in section compatibility can be determined by measuring the rough-in
section as shown in Figure 2.
Installation
When the rough-in section is modified, the loose warning label supplied with this retrofit kit must be affixed to the luminaire in a location visible after installation. Retrofit kit is voltage specific. Verify proper voltage before installation.
Electrical Connection
Step 1. Turn off electricity at the fuse or circuit breaker box.
Step 2. Remove existing trim section and housing (if applicable) to gain
access to the rough-in section junction box. Remove junction box access cover.
Step 3. Disconnect all primary input wires leading from input supply to
the ballast or socket.
Step 4. Install the supplied trim conduit whip into the junction box via
knockout using supplied ½” trade size fitting.
Note: Retrofit conduit whip assembly is provided with quick disconnect
connector located in LED driver junction box. Connector can be disconnected to
separate reflector from supply wire connection. This allows for easy
installation of supply wire connection to retrofit without reflector
interference. (Refer to Figure 4).
Step 5. Connect supply wires to the retrofit trim wires (Refer to
Figure 3).
Step 6. Make certain rough-in section junction box is grounded. Reinstall
junction box cove
Reflector Installation
Note: Rough-in section ring must be present to utilize provided friction
clips.
Step 1. Determine which friction clip to utilize. Two styles of mounting
friction clips (“A” & “B”, 3 each) have been provided for different retrofit
aperture ranges. This is to ensure best fixture retention when installing
reflector trim assembly. When utilizing provided mounting friction clips,
please refer to Figure 5 for proper friction clip aperture inside diameter
range. Aperture inside diameter can be determined by measuring rough-in
section as shown in Figure 2 on previous page.
Step 2. Install each clip along rough-in section ring (120° apart) by
pushing them upward on the edge of the rough-in section ring (See Figure 6
& Detail A).
Note: Existing Reflector retainer clips from old reflector/trim assembly
may need to be removed or bent back to allow proper LED retrofit reflector
installation.
WARRANTY
Limited warranty located at: www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx
Technical Services Phone 888-387-2212
Customer Support
One Lithonia Way • Conyers GA 30010 •
Phone 1-800-705-SERV (7378) • Visit us at
www.acuitybrands.com
©2021 Acuity Brands Lighting, Inc Rev 10/21 P5520
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>