ELVID CM7 Fieldvision 7 Inch Monitor User Manual

ELVID CM7 Fieldvision 7 Inch Monitor

INTRODUCTION

Thank you for choosing the Elvid FieldVision 7″ Monitor. This product will provide you with a crisp, clear full-color view on a screen that’s large enough to exhibit the finer details that may be missed on small built-in LCD camera screens.
Whether you’re using the Elvid FieldVision 7″ Monitor for filmmaking or professional photography, the vibrant 7″ display allows you to comfortably preview and review your work both on location and in the studio, and most importantly, will help you obtain an accurate focus at all times with its large monitor screen.

KEY FEATURES

• Compatible With HDSLR Cameras 8 Camcorders
• Bright 800 x 480 Pixel Screen Assists Framing
• Supports Signal Resolution Up To 1920 X 1440
• Dual A/V, HDMI 8 VGA Connectivity
• Dual AC 8 Battery Power
• Built-In Audio Speaker

PRODUCT CONTENTS

• 7″ Field Monitor
• 3′ Mini-HDMI
• To HDMI Cable
• 5′ Standard HDMI Cable
• Dual A/V Cable
• AC Power Adapter
• Car Power Adapter
• Battery a Battery Plate
• Battery Charger
• Wireless Infrared Remote
• Hot Shoe To 1/4 20 Adapter
• Storage Case

NOTE: Additional battery plates and/or battery adapters compatible with other popular brands can be purchased by visiting www.elvidcinema.com

MONITOR DIAGRAM

The monitor can be used in a variety of settings and configurations to provide the viewer with access to images appearing on actual camera screen.

WIRELESS REMOTE

The wireless remote can be used to turn the monitor’s power on and off, adjust volume, and access and adjust all the menu settings.

DUALA/V CABLE

The Dual NV Cable allows the user to connect the Elvid FieldVision 7″ Monitor to two separate devices at the same time and easily switching between them.

POWERING ON 8 OFF

The Elvid FieldVision 7″ Monitor can be powered in one of three ways: via the included lithium battery; included AC adapter; or included car adapter. Connect monitor to battery by sliding into battery plate on rear of device. The power port found on rear of monitor connects directly to the AC power adapter, car power adapter, or battery.
Depending on which power source is being utilized at the time, be sure that the appropriate cord is connected directly to
power port.
Upon connecting unit to power source, unit will display a red indicator light and be placed in standby mode. Press power button found on unit or on wireless remote to activate power mode. To place unit in standby mode, press power button again. Press Input found on unit or AV/PC found on wireless remote to select appropriate connection and switch between VGA, AV1, AV2 a HDMI inputs.

NOTE: When using monitor device on an HDSLR camera while in Camera Mode, be sure to switch camera setting to Live View for best results.

MOUNTING MONITOR

When connecting cables from the Elvid Field Vision 7″ Monitor to a camera device, ensure that the camera remains off during the entire linking process.
If mounting directly on camera, connect device with Mini-HOM I Cable to provide adequate signal by inserting HDMI connector into HDMI input port found on monitor.
When connecting monitor to other devices that accept standard HDMI connections, then connect device by utilizing the Standard HDMI Cable.

When using the Dual A/V cable, insert A/V input jack into the monitor unit. Insert remaining three prong connectors into appropriate video (yellow jacks) and audio (white jack) inputs.
When mounting monitor directly on camera or rig, attach device to included hot shoe 1/4 20 adapter and fasten device tightly.

MENU SELECTION

The Elvid Field Vision 7″ Monitor offers multiple customizable options via the device menu. You can adjust the display brightness, contrast, picture scale, values, sound settings and more. To access menu options, begin by pressing Menu button. Then press th . and “”‘ buttons to cycle through the menu features found on side tab; press menu button at any time during this sequence to exit.
Once in the side tab area, enter into the sub-menu to adjust settings by pressing the buttons; then scroll up or down
by pressing the   buttons. You can press to adjust numbers lower or higher, or press to open or select options from drop down menu. Press Menu button when completed to return to side tab area; press Menu button again to exit.

NOTE: These options can only be accessed while monitor device is connected to a camera.

MAIN MENU

COLOR

Brightness – To adjust the monitor brightness values
Contrast – To adjust contrast of image on screen
Hue – To adjust the color hues displayed on screen Saturation – To adjust the screen color saturation
Color temperature – To adjust the contrast of color temperature (Not accessible in A/V mode)

OSD

Language Options

• English
• Simplified Chinese
• French
• Italian
• German
• Spanish
• Traditional Chinese
• Japanese
• Korean
• Russian

Adjust OSD Horizontal
Position – To adjust menu screen position in horizontal format Adjust OSD Vertical
Position – To adjust menu screen position in vertical format
Adjust OSD Timeout – To turn off display setting menu; timing format is in seconds Adjust Transparency
Level – To adjust the levels of transparency of the menu screen

FUNCTION

Reset – To reset device back to original factory default settings
Aspect Ratio – To switch screen mode between 16:9 / 4:3 (Default mode is 4:3)
Left/Right Rotation – To flip screen image horizontally
Up/Down Rotation – To flip screen image vertically

SOUND

Adjust Volume – Adjusts the sound higher or lower

BRIGHTNESS 6VOLUME

To instantly adjust screen brightness without entering into Menu mode, simply press the button to cycle through sequence of brightness levels; upon sequencing through all levels, default brightness setting will reappear and sequence can be performed again. Note that this feature will not work when display is in Menu mode.
To instantly adjust device volume without entering into Menu mode, simply press the buttons to rapidly lower or raise volume levels. Note that this feature will not work when display is in Menu mode.

TROUBLE SHOOTING

Issue: Image appears to be displayed only in black a white
Solution: Ensure the color saturation and brightness levels are set properly Issue: Power is on but no picture is displayed on screen
Solution: Ensure the proper cables are connected securely to output connectors; verify that correct power adapter is being used to power unit; make sure the Elvid FieldVision 7″ Monitor is set to accept the correct connection via the Input button.

Issue: Abnormal or erroneous colors appear on monitor screen Solution: Ensure that all cables are securely connected and verify that there are no broken or loose pins in cable connector that may be interfering with quality of connection; reset the device to the original factory default settings, which can be accessed in the main menu.

Issue: Remote control device is not operating properly
Solution: Ensure that batteries are installed properly in remote control and possess an adequate charge; verify that infrared signal from remote control has a direct line of sight with infrared receiving area on monitor

SAFETY WARNINGS

• Do not attempt to disassemble, repair or perform any unauthorized modifications on device
• Do not handle with wet hands, immerse in liquids or expose to water and rain; failure to do so may result in fire or electric shock
• Device contains small parts which may pose a choking hazard; keep out of reach of children
• Do not operate device in presence of flammable gas or vapors
• Observe caution when handling batteries; only use batteries approved by the manufacturer of this product
• Batteries are prone to leakage when fully discharged; to avoid damaging product be sure to remove batteries when leaving product unattended
• Do not use or leave device in conditions of extreme heat, severe cold or high humidity Turn off power of camera and monitor before connecting or disconnecting cables
• Please dispose of used batteries, packaging and old devices in accordance with appropriate environmental regulations

SPECIFICATION

MONITOR|
---|---
Display| 7″ LCD
Resolution| 800×480
Max Input Resolution| 1920×1440
Brightness| 250 cd
Contrast| 500:1
Viewing An| 70°/70°,50°/60° (UR,U/D
Video Signal Input| 0.T1 .4Vp-p/75Q
VGA Signal Input| H:30-60kHz V:60-75Hz
Speaker| 2.5W/8Q
Color System| PAL-4.43; NTSC-3.58
Voltage| DC12V±10
Signal Input| PC (VGA). AVl AV2.HDMI
Power Consumption| Sw

BATTERY CHARGER|
---|---
Input:| AC 100-240V 50-60Hz
Max| 150mA
Output:| DC 4.2V/8.4V 600mA
AC ADAPTER|
Input:| 100-240V 50-60Hz 0.60A Max
Max| 12V 1200mA
CAR CHARGER|
Input:| 12-24V DC
Output:| 12V DC

LIMITED ONE-YEAR WARRANTY

Elvid provides a limited warranty that this product is free from defects in materials and workmanship to the original purchaser under normal use for a period of one (1) year from the original purchase date or thirty (30) days after replacement, whichever occurs later (the ”Warranty Period”). Our responsibility with respect to this limited warranty shall be limited solely to repair or replacement, at its option, of any product which fails during normal consumer use. To obtain warranty coverage during the Warranty Period, contact your place of purchase [‘Seller”) to obtain a return merchandise authorization C’RMA”) number, and return to Seller the defective product along with proof of purchase and the RMA number. This warranty does not extend to damage or failure which results from misuse, neglect, accident, alteration, abuse, improper installation or maintenance. EXCEPT AS PROVIDED HEREIN, ELVID MAKES NEITHER ANY EXPRESS WARRANTIES NOR ANY IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. This warranty provides you with specific legal rights, and you may also have additional rights which vary from state to state. © Copyright 2012 Gradus Group.

www.elvidcinema.com

References

• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>