IHOME XT10 BT True Wireless Earbuds-Instruction Manual
- June 4, 2024
- iHome
Table of Contents
IHOME XT10 BT True Wireless Earbuds
Package Contents
- XT-10 True Wireless Earbuds
- Charging Travel Case
- 8 Ear Cushions in 3 sizes (2 Small, 2 Large, 4 Medium)
- USB-A to USB-C Charging Cable
- Instruction Manual
Specifications
- Bluetooth® Version: 0
- Working distance: 33 ft
- Charge Connector: USB-C
- Speaker Size: 010 mm
- Frequency Response: 20Hz – 20KHz
- Sensitivity: 107 dB +3 dB
- Charging voltage: 5V/1A
- Case Battery: 350 mAh
- Case Charge time: 1,5 hrs
- Earbuds Battery: 2 x 40 mAh
- Earbuds Charge time: t1 hr
- Distortion Rate: THD < 1%
Operation Guide
Getting Started
Before using this device, fully charge it. Charging instructions can be found on page 6. Open the charging case and take out the earbuds. Both LED lights will flash red and blue until one of the earbuds flashes red and blue, while the other earbud flashes blue, indicating that the right and left earbuds have synced to each other.
Pairing
- Go to Bluetooth Settings on your mobile device.
- Turn Bluetooth ON, on your device.
- On your Bluetooth” device, select “iHome XT-10” from the list of available devices.
- The earbud indicator LEDs will shine flash blue to indicate they are connected.
Basic Functions
Right Earbud
- Double tap the control surface to play or pause the audio.
- Tap and hold to skip to the next audio track.
- Single tap to raise the volume.
Left Earbud
- Tap and hold to skip to the previous audio track.
- Single tap to lower the volume.
Phone calls
When there is an incoming call, the unit will pause the playback and ring to alert you of the call. Phone call functions work the same on either of the earbuds. To answer an incoming call, single tap the control button of either earbud, To end a call, double tap the control surface. To reject an incoming call, tap and hold the control surface.
- Volume controls may not work during phone calls with some smartphone models.
Troubleshooting
Earbuds do not sync with each other:
- Place the earbuds in the case, then take out the earbuds, ensuring both earbuds are turned on.
- On each earbud, press and hold the control surface for 5 seconds. The earbud will turn off after the LED flashes purple 3 times.
- Replace the earbuds in the charging case.
- Repeat the Getting Started process,
Earbuds do not pair to device:
- Turn the Earbuds OFF by pressing the control surface on each earbud until the LED blinks red, and then turns off.
- Replace the earbuds in the case. Turn your device’s Bluetooth” OFF and then back ON. Then repeat the pairing process.
Charging
-
Replace the earbuds in the case.
-
Connect the USB-C charging cable to the charging port on the back of the case.
-
Plug the cable into a standard USB 5V/1A or higher power output.
When you plug the case into a charging mechanism the indicator light on the front of the case flashing glow. This means the case battery is being charged. While this is happening the lights on the buds inside the case glow solid red, which indicates they are being charged. When fully charged the case LED will glow solid and the earbud LEDs will shut off. -
When fully charged, unplug the charging cable from the power source.
If want to charge the earbuds from the charge case internal battery, simply replace them in the case. The LED on the front of the case glows solid and the LEDs on the buds will glow solid red.
Warnings
- Do not use this unit for anything other than its intended use.
- Do not puncture, throw, drop, bend, or modify this product.
- Do not throw this product into fire or water.
- Do not short-curcuit the battery with any metal or metallic objects.
- Do not expose this product to corrosive liquids Such as salt water.
- Do not operate the unit if it has been wet or moist to prevent against electric shock and/or injury to yourself and damage to the unit.
- Do not allow children to play with this product as it is not a toy, and may present a choking hazard.
- Avoid leaving your device in direct sunlight, such as on the dashboard, console, or seat of a vehicle,
- Do not leave your device, or use your device, in any area where the temperature is likely to drop below 32°F, or may exceed 140°F, such as inside a closed vehicle on a hot day.
- Repairs to electrical equipment should only be
- performed by a qualified electrician. Improper repairs may place the user at serious risk.
- Protect your hearing by always listening at a safe level. Prolonged use at elevated volumes may affect your hearing capacity and could result in hearing loss.
- Use the earbuds with this charging case only.
- To avoid damage to the charging case, please only use a USB SV/IA or higher charger In order to ensure the battery life, charge normally at least once a month.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/Tv technician for help
Caution : Any changes or modifications not expressly approved could void the user’s authority to operate the equipment.
FAQs
How are iHome wireless earphones used?****
To turn on the headphones, tap them. On an Android device, you can long-press the Bluetooth icon by lowering the top shade. You can quickly enable Bluetooth when the option displays and begin searching for devices. By tapping the names of the headphones, you can pair them.
How long do iHome earphones require to charge?****
The Power/Charging/Pairing signal will turn red while charging. The indicator will go off when the battery is fully charged. Remember to completely charge the battery before using it for the first time. A typical charge ought to last for about 3.5 hours.
iHome Bluetooth headphones: how long do they last?****
The padded headband and ear cushions allow for comfortable extended listening, and the Bluetooth wireless technology provides an audio listening range of up to 30 feet. For 10 to 12 hours, a rechargeable battery can be continually utilised.
Do Android devices support iHome earbuds?****
The best way to control your iHome Smart Plug from an Android phone or tablet, virtually anywhere in the world, is using the iHome Control app.
How durable are iHome earbuds?****
Easy to Use Design You can simply fit the case in your palm or pocket. Your headphones have a maximum listening time of five hours at a moderate volume and twenty hours while they are charging.
Are iHome earbuds water resistant?****
Features iPX5-rated water-resistant design for weather protection and sweat- proof use. Without having to mess with connections or cords, enjoy rich audio with greater bass response and detail (earpieces are connected by a stylish fl at cable for tangle free use).
How are iHome earbuds turned off?****
Turn off the earbuds by pushing the control surface on each one until the LED begins to flicker red.
Why won’t my iHome headphones charge?****
If the charging light does not turn on, first try charging another device with the Micro USB cord. If the other device is also unable to charge, swap out the Micro USB cord.
Without a case, how do you charge wireless earbuds?****
To charge earphones with a micro USB, you must attach a Micro USB cable to your device and either a computer or a USB converter. You then have to wait till your earbuds are fully charged.
How durable are wireless earbuds?****
Before their battery runs out, true wireless headphones typically have a battery life of 3 hours or less. Charger cases are useful in this circumstance. Your headphones’ listening time can be increased by at least 5 to 6 hours with the use of a suitable charging case.
What are the uses of iHome?****
Video can be sent from your iPod or iPhone to your television via the ports on the rear of your iHome. Your iPod or iPhone’s model determines which video-out features are supported.
Is it safe to only use one iHome earbud at a time?****
Using only one earbud puts your hearing at risk and increases your chance of developing ear strain. This is mostly a result of binaural loudness summation, a process by which your brain processes sound.
Can two iHome earbuds be used separately?****
You can use them independently; the casing is the key. They both turn on when you take them out of the case, make a connection, and begin looking for a device. The other earphone is checked before looking for a gadget if you only remove one.
Are iHome headphones secure?****
If they are not regularly cleaned, earbuds can easily introduce bacteria to the ears when placed directly into the ear canal. Additionally, earbuds block the ear’s airway, which encourages the development of germs. Together, these factors raise the possibility that germs will get into the more sensitive parts of the ears.
Can iHome wireless earbuds travel a long distance?****
The range of the Bluetooth® connection is approximately 30 feet (10 meters). The maximum communication range, however, may differ based on barriers (people, metal, walls, etc.) or electromagnetic conditions.