CASIO 5153 Watch Band Installation Guide
- June 13, 2024
- Casio
Table of Contents
**CASIO 5153 Watch Band
**
Reading The Display
Setting Digital Time
-
Press and hold B in the Time display to set time.
-
Press A on an hourly time signal to correct seconds.
-
Press B to shift fl ashing digit(s).
The digit(s) to be changed will fl ash. -
Each press of A increments the digit by one. Keep pressed to move at a high speed.
-
Resetting the seconds to 00 while the current count is in the range of 30 to 59 causes the minutes to be increased by 1. In the range of 00 to 29, the seconds are reset to 00 without changing the minutes.
-
In the case of 12/24-hour selection, each press of A switches the display between
12-hour and 24-hour format alternately. (Auto return function)
If no button is pressed for a few minutes, the display automatically returns to the regular timekeeping mode.- Press B to complete.
Setting Analog Time
- When the second hand is at 12 o’clock position, stop the second hand by pulling the crown out.
- Set the hands by turning the crown.
- Press the crown in on a time signal.
A gain or loss of one second or less may result from properties of mechanical parts.
Setting Calendar
- Press and hold B in the calendar display to set calendar.
- Each press of A increments the digit by one. Keep pressed to move at a high speed.
- Press B to shift fl ashing digit(s). The digit(s) to be changed will fl ash.
- Press B to complete.
Setting Daily Alarm
If the daily alarm is set the beeper sounds for 20 seconds at the preset time
every day until cleared. To stop the beeper while sounding, press any button.
If the hourly time signal is set, the alarm sounds every hour on the hour.
- Press and hold B in the daily alarm mode to set time.
- Each press of A increments the digit by one. Keep pressed to move at a high speed.
- Press B to shift fl ashing digit(s). The digit(s) to be changed will fl ash.
x At this time daily alarm and hourly time signal automatically turn on.
-
In the case of daily alarm and hourly time signal on or off setting, the display changes as shown nearby with every press of A.
[ON or OFF setting of daily alarm and hourly time signal]
(Auto return function)
If no button is pressed for 2 to 3 minutes in the daily alarm setting mode, the display automatically returns to the initial daily alarm mode display.- Press B to complete
-
When the watch is in the 24-hour format, the alarm time is also displayed in the 24-hour format.
Setting Dual Time
- Press and hold B in the dual time display to set time.
- Each press of A increments the digit by one. Keep pressed to move at a high speed.
- Press B to shift fl ashing digit(s). The digit(s) to be changed will fl ash.
-
In the case of 12/24-hour selection, each press of A switches the display between 12-hour and 24-hour format alternately
(Auto return function)
If no button is pressed for 2 to 3 minute, the display automatically returns to the regular timekeeping mode display.- Press B to complete.
Stopwatch Operation
Press B to start or stop.
Press and hold B to reset.
A signal confi rms start/stop operation.
(Working range) The stopwatch display is limited to 59 minute 59.99 seconds,
for longer times reset and started again.
Specifications
Accuracy at normal temperature: ±30 seconds a month
Display capacity
-
Regular timekeeping mode
Analog: Hour, minute and second hands
Digital: Hour, minute, second, pm (P), month, day, day of the week
Time system: Changeover between 12/24-hour formats
Calendar system: Auto-calendar set at 28 days for February -
Stopwatch function
Measuring capacity: 59 minutes 59.99 seconds
Measuring unit: 1/100 second
Measuring modes: Normal time and net time -
Daily alarm
-
Hourly time signal
-
Dual time
Battery: One silver oxide battery (Type: SR920W) Approximately 2 years on type SR920W (assuming alarm operation 20 sec./day)
NOTE: THERE IS NO WAY unit components can be damaged or malfunction, due to misoperation of buttons. If confusing information appears on the display it meansentry sequence was incorrect. Please read the manual and try again.