Hinyx W501 2-in-1 Magnetic Wireless Charging Folding Stand User Manual
- June 13, 2024
- Hinyx
Table of Contents
Hinyx W501 2-in-1 Magnetic Wireless Charging Folding Stand
PRODUCT INFORMATION
- MODEL NAME : 2-in-1 Magnetic Wireless Charging Folding Stand
NOTE : Please read this manual carefully before use “Non-contractual graphics and pictures
Product introduction
- Applicable mobile phone: iPhone 12 or above or mobile phone with magnetic absorption function.
- Applicable headphones : AirPods 2, 3, 4 generation and other wireless charging headphones,
The product is a magnetic two-in-one wireless charger for t he iPhone 12, 13 or above mobile phone magnetic charging, AirPods 2, 3, 4 generation wireless charging, headphones can also support QI standard allows mobile phones and other electronic devices to charge wirelessly
State of the LED
- Put the power on standby, the power indicator lights green and always lighten up.
- Mobile phone charging green light breathing, standby green steady on.
- Headffl charging green light breathing, standby green steady on,
- Foreign body sensation, green light flashing.
Product parameters
- Input voltage: 5V/2A,9\//2A, 12VJ3A
- Wireless output 1 : 5W /7.5W /10W {15W
- Wireless output 2: 5W /7.5W /10W /15W
- Working frequency: 115-205Khz
- Receiving distance: 0-6mm
- Conversion efficiency: 75 %
- Product size: L123 x W 59xH9mm
Frequently asked questions
- Wireless charging is slower
- Check whether the power supply adapter has more than 18W power, the phone itself or the external receiver coil allows. Maybe the size of the wireless charging current is not the same, or the phone is charging when the application runs power consumption, build. Reduce or close the program
- The wireless charging of the mobile phone is intermittent and the indicator lights are flashing.
- Check whether the power supply adapter has more than 18W power, the phone itself or the external receiving line. The loop allows the wireless charging current to vary in size, or the amount of work the app is running while the phone is charging. Consume large, recommend to reduce or close the program
- Charging fever
- It is normal for the receiving coll or transmitting plate of wireless charging to have slight heating. It is recommended to adjust the charging position.
- The main indicator is normal, but the phone doesn’t charge
- The receiver coil of the mobile phone is faulty or the charging position is not aligned
- The power indicator is off
- Host failure, contact after-sales maintenance
Matters needing attention
- Please use an adapter with more than 18W power for power supply (QC 3.0 or PD18W or above) otherwise the charging may be unstable
- Do not place metal objects or magnetic materials near the charging area. Otherwise, ihe product may be damaged or charged don’t work
- If the charging stops due to overheating of the receiving coil or transmitting panel during the charging process, please remove the charging product and try charging again after cooling.
- When an exception occurs, the indicator light will blink and automatically protect
Safety instructions
- Do not forcibly pull the power cable. Otherwise, the power cable may be broken or removed.
- Do not disassemble the main engine or put it into fire or water to avoid short circuit.
- Do not use in severe high temperature, humidity, or corrosive environment to avoid damage.
Product after-sales guide
Thank you for buying our wireless charger, in order to ensure that you gel reliable after-sales service. Please carefully read the following warranty instructions.
Products in the process of use can not be used normally or normal use of fault, and through our company. After identification, we can enjoy our after- sales service commitent, the following circumstances are not within the scope of warranty:
- Accessories are not under warranty.
- The foult is caused by improper user operations.
- Disassembly by non-working personnel is not within the scope of warranty.
- The products beyond the warranty period are not covered by the warranty.
- Failure 10 provide a warranty card is not covered by the warranty. When not in use for a long time, please disconnect the power supply of the product, and keep it out of the reach of children’s play products.
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause ham,ful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authorityto operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be detem,ined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect ihe equipment into an outlet on a circuit differeni from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC WPT exposure statement:
The equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance between 20cm the radiator your body.
-
Date : 10.07.23
Designation : Instruction manual -
Dimensions : 90 x 690 mm
-
Materials : Paper
-
Colors : Black White
Designed In France. Made In China.
WARNING : Cancer and Reproductive Harm www.P65Warnings.ca.gov