SIEMENS SX75Z802BE Fully Integrated Dishwasher User Guide

SIEMENS SX75Z802BE Fully Integrated Dishwasher

Product Information

The product is a dishwasher that provides convenient and efficient cleaning of tableware. It comes with various features and settings to ensure optimal performance. The dishwasher can be connected to a mobile device using the Home Connect app, allowing users to control and change settings remotely. The appliance also has a water softening system and dispenser for special salt and rinse aid.

Overview of Water Hardness Settings:

Programmes:

Product Usage Instructions

1. Before using the dishwasher for the first time, read the instruction manual and safety information.

2. Setting up Home Connect:

3. Install the Home Connect app on your mobile device and follow the instructions.

4. Scan the QR code with the Home Connect app.

5. Water Hardness Settings:

6. Refer to the water hardness values in the instruction manual for your country.

7. To set the water hardness, press the corresponding value on the display.

8. To save the settings, press and hold for 3 seconds.

9. Adding Special Salt:

10. Unscrew the lid of the special salt dispenser and remove it.

11. If it’s the initial start-up, fill the dispenser with water.

12. Add the special salt to the dispenser, ensuring no detergent is added.

13. Place the lid back on the dispenser and turn to close.

14. Adding Rinse Aid:

15. Press the catch on the lid of the rinse aid dispenser and lift it.

16. Add rinse aid up to the maximum mark.

17. Close the lid of the dispenser until it clicks into position.

18. Adding Detergent:

19. Add the detergent to the dry detergent dispenser according to the recommended amount.

20. Close the lid of the detergent dispenser until it clicks into position.

21. Using the Appliance:

22. Load the tableware, ensuring it is suitable for dishwashers and removing large food remnants.

23. Switch on the appliance.

24. Select the desired programme.

25. Start the programme.

26. At the end of the programme, remove the tableware.

27. Cancelling a Programme:
    To cancel a programme, press and hold for approximately 4 seconds. The programme will be cancelled and end after approximately 1 minute.

28. Cleaning Filters:

29. After each wash, check the filters for residue.

30. Turn the coarse filter anticlockwise and remove it for cleaning.

Before using for the first time, read the instruction manual and the safety information it contains.

Setting up Home Connect

Tip: Connect your appliance to a mobile device. You can conveniently change all settings using the Home Connect app.

1. Install the Home Connect app on your mobile device and follow the instructions.
2. Scan the QR code with the Home Connect app.

Overview of water hardness settings

You can find an overview of the water hardness values that can be selected here.
A table of country-specific units can be found in the instruction manual.

Setting the water softening system

1. Press ⁠.
2. To open the basic settings, press for 3 seconds.
   • The display shows .
   • The display shows
3. Press setup repeatedly until the right water hardness has been set.
4. To save the settings, press setup for 3 seconds.

Adding special salt

To avoid damage to the appliance, only add special salt to the dispenser for special salt just before the programme starts.

1. Unscrew the lid of the dispenser for special salt and remove.
2. On initial start-up: Fill the dispenser right up with water.
3. Add the special salt to the dispenser. The water in the dispenser is displaced and forced out. Never add detergent.
4. Place the lid back on the dispenser and turn to close.

Adding rinse aid

1. Press the catch on the lid of the dispenser for rinse aid and lift ⁠.

2. Add rinse aid up to the max mark.

3. Close the lid of the dispenser for rinse aid.
   The lid clicks into position.

Adding detergent

1. Add the detergent to the dry detergent dispenser.

2. Close the lid of the detergent dispenser.

   • The lid clicks into position.

Programmes

The programme data has been meas-ured in the laboratory according to European standard EN 60436.
The consumption figures depend on the programme and additional func-tion selected.
The runtime will change if the rinse aid system is switched off or rinse aid needs to be added.

How to use your appliance

1. Load the tableware.
   Only clean tableware that is suitable for dish-washers. Remove large remnants of food from the tableware. Check that the spray arms can rotate freely.

2. Add detergent.

3. Switch on the appliance ⁠.

4. Select the programme.

5. Start the programme start.

6. Remove the tableware at the end of the programme.

7. To cancel the programme, press approx. 4 seconds.
   The programme is cancelled and ends after approx. 1 minute.

Cleaning filters

1. After each wash check the filters for residue.

2. Turn the coarse filter anticlock-wise and remove the filter system ⁠.

3. Pull down the micro filter to re-move.

4. Press the locking catches together and lift the coarse filter out ⁠.

5. Clean the filter elements under running water.

6. Re-assemble the filter system.

7. Insert the filter system into the appliance and turn the coarse filter clockwise. Make sure that the arrow markings match up.

Cleaning spray arms

1. Unscrew the upper spray arm and pull down to remove ⁠.

2. Pull up the lower spray arm to remove.

3. Check the outlet nozzles on the spray arms for blockages un-der running water and remove any foreign bodies.

4. Insert the lower spray arm.

   • The spray arm clicks into position.

5. Insert the upper spray arm and screw it firmly in place.

Clean wastewater pump

1. Disconnect the appliance from the power supply.

2. Remove the filter system.

3. Scoop out any water.

4. Prise off the pump cover using a spoon and grip it by the crosspiece.

5. Lift the pump cover inwards at an angle and remove.

6. Remove any remnants of food and foreign bodies in the area of the impeller.

7. Insert the pump cover and press down ⁠.

   • The pump cover clicks into position.

8. Install the filter system.

Troubleshooting

Fault : Cause and troubleshooting

• E:32-00 will light up al-ternately or indicator for water supply lights up.

  • Supply hose is kinked.

  • Install the supply hose without kinks.

  • Water tap is turned off.

  • Turn on the water tap.
    Water tap is jammed or furred up.

  • Turn on the water tap.
    The flow rate must be at least 10 l/min when the water sup-ply is open.
    The filters in the water connection of the supply or AquaStop hose are blocked.

  • Switch off the appliance.

  • Pull out the mains plug.

  • Turn off the water tap.

  • Unscrew the water connection.

  • Remove the filter from the sup-ply hose

  • Clean the filter.

  • Re-insert the filter in the supply hose.

  • Screw the water connection back on.

  • Check the water connection for leaks.

  • Restore the power supply.

  • Switch the appliance on.

• E:92-40 will light up al-ternately.
  Filters are soiled or blocked.

  • Clean the filters.

• E:61-02 will light up al-ternately.
  Wastewater pump is blocked.

  • Clean the wastewater pump.
    Cover of the wastewater pump is loose

  • Secure the cover of the Wastewater pump so it clicks into position.

• Remnants of food on tableware.
  Tableware is placed too close together or basket is overfilled.

  • Arrange tableware with sufficient space in between. The spray jets must reach the surfaces of the tableware.

  • Avoid points of contact.

  • Spray arm rotation is blocked.

  • Arrange tableware so that it does not obstruct spray arm rotation.
    Spray arm nozzles are blocked.

  • Clean the Spray arms.
    Filters are soiled.

  • Clean the filters.
    Filters are inserted incorrectly and/or not engaged.

  • Insert the filters properly.

  • Engage the filters.
    Washing programme selected too weak.

  • Select a more intensive washing programme.

  • Adjust the sensitivity of the sensors.

• Removable streaks are present on glasses, glass-ware with a metallic appearance and cutlery.

  • Amount of rinse aid to be dispensed is set too high.
    Set the rinse aid system to a lower setting. No rinse aid has been added.

  • Add rinse aid.

• Rust spots on cutlery.
  Cutlery is not sufficiently rust-resistant. Knife blades are often more severely affected.

  • Use rust-resistant tableware.
    Cutlery may also rust if washed together with rusting items.

  • Do not wash rusting items.

• Detergent residue is present in the detergent dispenser or the tablet collecting tray.
  Spray arms were blocked by tableware so detergent was not rinsed out.

  • Check that the spray arms are not blocked and can rotate freely.

• All LEDs light up or flash or the rinse programme does not continue running.
  Electronics have detected a fault.

  • Press the main switch button for approx. 4 seconds. The appliance is reset and restarted.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>