Sony SS-MB150H Speaker System User Manual

Sony SS-MB150H Speaker System

Introduction

Investing in a high-quality speaker system like the SS-MB350H is a great way to elevate your audio experience. To ensure you get the most out of your speakers, it’s crucial to understand how to properly set them up and take care of them. This article will guide you through essential aspects of speaker connections, precautions, placement, and specifications.

Connections

• Before connection, turn off the amplifier to avoid damaging the speaker system.
• This speaker system is driven best by an amplifier or receiver rated as per the wattage indicated in the specification section. A low-powered amplifier could result in signal clipping which could result in tweeter burn-out. Therefore, it is recommended to use an amplifier or receiver with a sufficient power rating.

Note: Avoid driving the speaker system continuously with a wattage exceeding the maximum input power of each speaker.

Precautions

• Do not attempt to open the enclosure or remove speaker units. There are no user-serviceable parts inside.
• Keep recorded tapes, watches, and personal credit cards using magnetic coding away from the speaker system.
• Periodically wipe the cabinet with a soft cloth. Do not use any type of scouring powder, abrasive pad, or solvent.
• Be sure to install the grill net in the correct direction.

Speaker Placement

• Please note that room acoustics can often produce large differences in the sound for small changes in speaker placement.
• Set up your speaker system on a hard, flat surface.
• Place the speaker system against a hard wall with its back about 10 cm away from a wall. The proportion of bass increases as you move a speaker close to intersecting room surfaces (wall and wall, etc.).
• Place the right and left speakers in a similar acoustic environment.
• It is recommended that the speaker/listener relationship be an equilateral triangle.

Specifications

Specifications – SS-MB350H:

• Speaker System: 3-way, magnetically shielded
• Loudspeaker Units:
  • Woofer: 20 cm (8 in.), cone type
  • Midrange: 8 cm (3 in.), cone type
  • Tweeter: 2.5 cm (1 in.), balanced dome type
• Enclosure Type: Acoustic suspension
• Rated Impedance: 8 ohms
• Power Handling Capacity: Maximum input power of 120 watts
• Sensitivity Level: 88 dB (1 W, 1 m)
• Frequency Range: 50 Hz – 50,000 Hz
• Dimensions (w/h/d): Approx. 240 × 530 × 255 mm (9 1/2 × 20 7/8 × 10 1/8 in.) including front grille
• Mass: Approx. 6.5 kg (14 lb 5.3 oz)
• Supplied Accessory: Speaker cord 2.5 m (8.2 ft.) (2)

Specifications – SS-MB250H:

• Speaker System: 2-way, magnetically shielded
• Loudspeaker Units:
  • Woofer: 16 cm (6 1/2 in.), cone type
  • Tweeter: 2.5 cm (1 in.), balanced dome type
• Enclosure Type: Acoustic suspension
• Rated Impedance: 8 ohms
• Power Handling Capacity: Maximum input power: 120 watts
• Sensitivity Level: 87 dB (1 W, 1 m)
• Frequency Range: 60 Hz – 50,000 Hz
• Dimensions (w/h/d): Approx. 220 × 370 × 215 mm (8 3/4 × 14 5/8 × 8 1/2 in.) including front grille
• Mass: Approx. 4.8 kg (10 lb 9.3 oz)
• Supplied Accessory: Speaker cord 2.5 m (8.2 ft.) (2)

Specifications – SS-MB150H:

• Speaker System: 2-way, magnetically shielded
• Loudspeaker Units:
  • Woofer: 13 cm (5 1/8 in.), cone type
  • Tweeter: 2.5 cm (1 in.), balanced dome type
• Enclosure Type: Bass reflex
• Rated Impedance: 8 ohms
• Power Handling Capacity: Maximum input power: 120 watts
• Sensitivity Level: 87 dB (1 W, 1 m)
• Frequency Range: 80 Hz – 50,000 Hz
• Dimensions (w/h/d): Approx. 170 × 250 × 185 mm (6 3/4 × 9 7/8 × 7 3/8 in.) including front grille
• Mass: Approx. 2.9 kg (6 lb 6.3 oz)
• Supplied Accessory: Speaker cord 2.5 m (8.2 ft.) (2)

Design and specifications are subject to change without notice.

Product Usage Instructions

Placement:

• Choose an appropriate location for your Sony SS-MB150H bookshelf speakers. They are designed for a bookshelf or shelf mounting.
• Ensure that the speakers are placed on a stable and level surface to prevent any vibrations or instability during playback.

Connectivity:

• Turn off the amplifier or receiver before connecting the speakers to avoid any potential damage to the speaker system.
• Use the provided speaker cables or appropriate auxiliary cables for connectivity, depending on your setup.
• Connect the speaker wires to the appropriate terminals on the back of each speaker. Observe proper polarity (positive to positive, negative to negative) to ensure correct audio reproduction.

Amplifier/Receiver Compatibility:

• To achieve optimal sound quality, use an amplifier or receiver that matches the wattage and impedance specifications indicated in the speaker’s specifications section.
• Avoid using a low-powered amplifier, as it may lead to signal clipping, which can result in tweeter damage.

Listening Environment:

• Consider the acoustics of your room, as they can significantly impact sound quality.
• Place the speakers against a hard wall with approximately 10 cm of space behind them. This placement can enhance bass response.
• Ensure that both the right and left speakers are in a similar acoustic environment.
• Aim for an equilateral triangle setup between the speakers and your listening position for balanced sound.

Listening Experience:

• Once the speakers are properly set up and connected, turn on your amplifier or receiver.
• Adjust the volume to your preferred level and enjoy high-quality audio playback.

Maintenance:

• Periodically wipe the speaker cabinets with a soft cloth to keep them clean. Avoid using abrasive materials or solvents.
• Ensure that the speaker grilles are correctly installed in the designated direction.

Following these usage instructions will help you make the most of your Sony SS-MB150H Bookshelf Speaker System and enjoy a rich and immersive audio experience.

FAQs

What is the difference between bookshelf speakers and floor-standing speakers?

Bookshelf speakers are smaller and designed to be placed on shelves, stands, or bookshelves, while floor-standing speakers are larger and stand directly on the floor. Floor-standing speakers typically produce deeper bass due to their larger size.

Can I use bookshelf speakers as part of a home theater system?

Yes, bookshelf speakers can be used as part of a home theater setup. They are often used as front or rear speakers to provide high-quality audio in smaller spaces.

What is speaker impedance, and why is it important?

Speaker impedance, measured in ohms, is a measure of a speaker's resistance to electrical current. It's essential to match the speaker's impedance with the amplifier's output impedance to ensure proper compatibility and prevent damage to the equipment.

How do I clean my bookshelf speakers?

You can clean bookshelf speakers by gently wiping the cabinet with a soft, lint-free cloth. Avoid using abrasive materials or solvents that can damage the finish. Be cautious when cleaning speaker grilles to prevent damage.

Can I connect bookshelf speakers to a computer or smartphone?

Yes, you can connect bookshelf speakers to a computer or smartphone using an appropriate audio cable or adapter. Ensure that your device has the necessary audio output ports.

What is the purpose of a magnetic shield on speakers?

A magnetic shield is designed to protect nearby electronic devices from magnetic interference generated by the speaker's magnets. It's particularly useful when placing speakers close to CRT televisions or other sensitive equipment.

What are the advantages of using bookshelf speakers over larger floor-standing speakers?

Bookshelf speakers are more compact and versatile, making them suitable for smaller rooms or as part of a multi-channel audio setup. They are also often more affordable than larger speakers.

How do I position bookshelf speakers for the best sound quality?

Place bookshelf speakers at ear level when seated for optimal sound quality. Ensure they are spaced apart to create a stereo soundstage, and experiment with speaker placement to find the best position for your room.

Can I use bookshelf speakers for both music and home theater applications?

Yes, bookshelf speakers can serve both music and home theater purposes. Many users use them in stereo setups for music and as part of a surround sound system for movies and gaming.

What is the difference between passive and active bookshelf speakers?

Passive bookshelf speakers require an external amplifier or receiver to power them. Active bookshelf speakers have a built-in amplifier and can be directly connected to audio sources like computers or smartphones.

How do I connect bookshelf speakers to an amplifier or receiver?

To connect passive bookshelf speakers, use speaker wire and connect the positive (+) and negative (-) terminals on the speakers to the corresponding terminals on the amplifier. Active bookshelf speakers may have different input options, such as RCA or 3.5mm audio jacks.

Can bookshelf speakers be wall-mounted?

Some bookshelf speakers are designed for wall mounting and come with mounting brackets. Ensure that the speakers you choose are compatible with wall mounting if you plan to use them this way.

Download This PDF Link: Sony SS-MB150H Speaker System User Manual

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>