SONY M1506GR Transmitter Module User Manual

SONY M1506GR Transmitter Module

Application Block Diagram

M1506GR is installed into the printed circuit board (PCB) of the application by reflow soldering process. LPWA output (“905M_ANT” pin) is connected to the antenna (SMA Reverse Connector) with 50 Ω line on PCB.

Antenna Information

Frequency: 860~928 (MHz)
Antenna type: monopole antenna (λ/2)
Maximum absolute gain: 3 dBi or less
Impedance: 50 Ω
Connector type: SMA-P (REVERSE)

PCB Information

Thickness: 1.6 mm (4-Layers)
Dielectric constant: 4.3

PCB Layout (from “905M_ANT” pin to antenna connector)

FCC and IC Regulatory Statements

FCC ID and IC Number

The following information must be indicated on the host device of this module;

[for FCC]

Contains Transmitter Module FCC ID: AK8M1506GR

or

Contains FCC ID: AK8M1506GR

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

*If it is difficult to describe this statement on the host product due to the size, please describe in the User’s manual.

[for ISED] Contains IC: 409B-M1506GR

The following statements must be described on the user manual of the host device of this module;

[for FCC] FCC CAUTION
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines.
This equipment should be installed and operated keeping the radiator at least 20cm or more away from person’s body.

[for ISED]

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment and meets RSS-102 of the ISED radio frequency (RF) Exposure rules.
This equipment should be installed and operated keeping the radiator at least 20cm or more away from person’s body.

This radio transmitter (409B-M1506GR) has been approved by Innovation, Science
and Economic Development Canada to operate with the antenna types listed
below, with the maximum permissible gain indicated. Antenna types not included
in this list that have a gain greater than the maximum gain indicated for any type
listed are strictly prohibited for use with this device.

FCC KDB 996369 D03 OEM Manual v01 rule sections

「General」: Applicable

This user manual describes the integration procedure per Sec. 2.2 to 2.12 of KDB 996369 D03.

「List of applicable FCC rules」: Applicable

This device complies with below part 15 of the FCC Rules. Part 15 Subpart C

「Summarize the specific operational use conditions」 : Not applicable

「Limited module procedures」 : Not applicable

「Trace antenna designs」: Applicable

M1506GR is installed into the printed circuit board (PCB) of the application by reflow soldering process.
LPWA output (“905M_ANT” pin) is connected to the antenna (SMA Reverse Connector) with 50 Ω line on PCB.

Antenna Information

Frequency: 860~928 (MHz)
Antenna type: monopole antenna (λ/2)
Maximum absolute gain: 3 dBi or less
Impedance: 50 Ω
Connector type: SMA-P (REVERSE)

PCB Information

Thickness: 1.6 mm (4-Layers)
Dielectric constant: 4.3

PCB Layout (from “905M_ANT” pin to antenna connector)

Fine tuning of return loss etc. can be performed using a matching network. However, it is required to check “Class1 change” and “Class2 change” which the authorities define then.

「RF exposure considerations」 : Applicable

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment should be installed and operated keeping the radiator at least 20cm or more away from person’s body.

「Antennas」: Applicable

The device is designed to use the antennas listed below. Do not modify the antenna or any other part of the module. Any modifications will invalidate the modular certifications and require new approvals  for the host system

「Label and compliance information」: Applicable

Following information must be indicated on the host device of this module.

Contains Transmitter Module FCC ID: AK8M1506GR

or

Contains FCC ID: AK8M1506GR

「Information on test modes and additional testing requirements」 : Applicable

Test modes should take into consideration different operational conditions for a stand-alone modular transmitter in a host, as well as for multiple simultaneously transmitting modules or other transmitters in a host product.

「Additional testing, Part 15 Subpart B disclaimer」: Applicable

The modular transmitter is only FCC authorized for the specific rule parts (i.e., FCC transmitter rules)
listed on the grant (Part 15 Subpart C), and the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification.

The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed.

「Note EMI Considerations」: Applicable

We recommend to use “best practice” RF design engineering testing and evaluation in case non-linear interactions generate additional non-compliant limits due to module placement to host components or properties. The host manufacturer is responsible for ensuring compliance with the applicable FCC rules for the transmitters operating individually and simultaneously. This includes compliance for the summation of all emissions from all outputs occupying the same or overlapping frequency ranges, as defined by the applicable rules.

「How to make changes」: Applicable

Only the grantee is permitted to make permissive changes. Please contact us at the address below.
https://www.sony-semicon.com/en/contact/index.html

References

• Contact Us | Sony Semiconductor Solutions Group

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>