JEGS 1998-2002 Direct-Fit Exhaust Kit Instruction Manual
- June 13, 2024
- JEGS
Table of Contents
JEGS 1998-2002 Direct-Fit Exhaust Kit
Product Information
| Part No. | Description |
|---|---|
| 167588 | Item 1: Nuts and bolts (not included) |
| 168271 | Item 2: Existing isolators and exhaust |
| 167681 | Item 3: Nuts and bolts (not included) |
| 168269 | Item 4: Existing isolators |
| 168270 | Item 5: Existing isolators |
Product Usage Instructions
-
Step 1: Disconnect the vehicle’s battery before removal of the OEM exhaust system. This will prevent electrical accidents and will reset the computer if it applies to the vehicle. Remove existing exhaust system from the vehicle. Only remove parts that will be replaced. Clean existing flange with a wire brush to ensure proper sealing.
-
Step 2: Attach item 2 to existing isolators and exhaust with item 1 (nuts and bolts not included).
-
Step 3: Attach item 5 to existing isolators item 2 with item 3 (nuts and bolts not included).
-
Step 4: Attach item 4 to existing isolators item 2 with item 3 (nuts and bolts not included).
-
Step 5: Connect item 2 slip fits with clamps provided.
-
Step 6: Ensure new exhaust is not contacting any portion f the underbody of the vehicle or drivetrain.
-
Step 7: Tighten all clamps starting from rear of the vehicle. (DO NOT EXCEED 30FT-LB WHEN TIGHTENING CLAMP AND CHECK ALL CLAMPS AFTER 50 MILES. RETIGHTEN IF NECESSARY)
WARNING
When working on, under, or around any vehicle exercise caution. Please allow
the vehicle’s exhaust system to cool before removal, as exhaust temperatures
may cause severe burns. If working without a lift, always consult vehicle
manual for correct lifting specifications. Always wear safety glasses and
ensure a safe work area. Serious injury or death could occur if safety
measures are not followed. BRExhaust recommends professional installation for
all products
Technical Support: 1-800-631-7271
BRExhaust: 1901 Corporate Ctr, Oceanside, CA 92056 www.brexhaust.com
BILL OF MATERIALs
- 167588
- 168271
- 167681
- 168269
- 16827z
STEP 1
(Carefully read all instructions before installation) Disconnect the vehicle’s
battery before removal of the OEM exhaust system. This will prevent electrical
accidents and will reset the computer if it applies to the vehicle. Remove
existing exhaust system from the vehicle. Only remove parts that will be
replaced. Clean existing flange with a wire brush to ensure proper sealing.
STEP 2
Attach item 2 to existing isolators and exhaust with item 1 (nuts and bolts
not included)
STEP 3
Attach item 5 to existing isolators item 2 with item 3 (nuts and bolts not
included)
STEP 4
Attach item 4 to existing isolators item 2 with item 3 (nuts and bolts not
included)
STEP 5
Connect item 2 slip fits with clamps provided
STEP 6
Ensure new exhaust is not contacting any portion of the underbody of the
vehicle or drivetrain.
STEP 7
Tighten all clamps starting from rear of the vehicle. (DO NOT EXCEED 30FT-LB
WHEN TIGHTENING CLAMP AND CHECK ALL CLAMPS AFTER 50 MILES. RETIGHTEN IF
NECESSARY
WARNING
When working on, under, or around any vehicle exercise caution. Please
allow the vehicle’s exhaust system to cool before removal, as exhaust
temperatures may cause severe burns. If working without a lift, always consult
vehicle manual for correct lifting specifications. Always wear safety glasses
and ensure a safe work area. Serious injury or death could occur if safety
measures are not followed.
BRExhaust recommends professional installation for all products Technical Support: 1-800-631-7271 BRExhaust — 1901 Corporate Ctr, Oceanside, CA 92056 ww.brexhaust.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>