JEGS 2650-1166 Mini Monster Tach Operation Instruction Manual
- June 3, 2024
- JEGS
Table of Contents
JEGS 2650-1166 Mini Monster Tach Operation
QUESTIONS
If after completely reading these instructions you have questions regarding
the operation or installation of your instrument(s), please contact Auto Meter
Technical Service at 815-899-0801.
You may also email us at service@autometer.com.
Additional information can also be found at
http://www.autometer.com/tech_faq.aspx
Configuration
The tachometer is configured at the factory for 4 PPR. (8 CYL)
To change the PPR, follow the steps below
- With no power applied to the tach, press and hold the RIGHT “-” button.
- While holding the “-” button, apply power to the tach by turning the ignition switch to the “Accessory” or “On” Do not start the engine! Release the RIGHT “-” button. The pointer will move to a position on the dial which indicates the default configuration of 4 PPR.Press and release the
- LEFT “+” button to change the PPR setting. This will cause the pointer to indicate 5 PPR, then 6 PPR, then down to 0.5 PPR, then 1, 1.5, 2, 2.5, 3, and back to 4 PPR. See the table below to find the pointer reading that corresponds to the desired PPR.
ENGINE
| | Most 2 cyl.| | Most 4 cyl.| | Most 6 cyl.| Most 8 cyl.| |
---|---|---|---|---|---|---|---|---|---
PPR| 0.5| 1| 1.5| 2| 2.5| 3| 4| 5| 6
DIAL RPM| 500| 1000| 1500| 2000| 2500| 3000| 4000| 5000| 6000
4. When the pointer indicates the desired PPR, press and releases the RIGHT “-” button to permanently store the settings and exit Configuration mode.
Mounting
- Loosen both bolts holding the shock strap to the mounting foot. Back both bolts (5⁄32” Allen wrench) out until each is only one or two turns into the spacer.
- Pass tach wires through the shock strap assembly and slide the tach casing into the shock strap assembly.
- Position Shift-Lite mounting bracket under shock strap as shown in Adjust Shift-Lite, tach, and mounting base to desired positions (see figure 4 for recommended shock strap position), and tighten bolts (5⁄32” Allen wrench) holding the mounting foot to shock strap to secure the assembly.
- Make sure the rubber section of the shock strap seats is properly to ensure proper fitment. Check to make sure the shock strap is approximately 3⁄4” (0.750”) between the center line of the strap and the step of the tachometer casing for best mounting. Plug the shift light into the tachometer Plug is directional, do not force fit!
- Recommended placement of the external Shift-Lite is at the 10 o’clock position. It is possible to place Shift-Lite in other positions in accordance with driver preference and vehicle mounting requirements.
- The special design of the tachometer base allows for a variety of mounting possibilities. Attach the base using the screws provided or use a pop rivet tool.
Note: Installation images shown may be different from your actual model.
Operation
Shift-Lite Set Mode
- To enter this mode, apply power to the tach by turning the ignition switch to the “Accessory” or “On” Do not start the engine! Press and release both the LEFT “+” and RIGHT “-” buttons at the same time. The pointer will indicate the current Shift-Lite set point.
- Using the RIGHT “-” and LEFT “+” buttons, move the pointer to the desired RPM for the new Shift-Lite Set Pressing the LEFT button will cause the pointer to move up (CW), pressing the RIGHT “-” button will cause the pointer to move down (CCW).
- Press and release both the LEFT “+” and RIGHT “-” buttons at the same time to save the setting and exit Shift-Lite Set
- Shift-Lite connector must be plugged in prior to
- See autometer.com/tech_installation.aspx for specific vehicle information.
CAUTION!
As a safety precaution, the Red wire of this product should be fused before connecting it to the positive (+) side of the 12V DC battery. We recommend using a 4 Amp, 3AG fast-acting type cartridge fuse (Littlefuse® # 312 004 or an equivalent) in line with the Red wire of our product.
WARNING
Warranty will be void if connected to coil when using an aftermarket ignition box such as, but not limited to products from the following manufacturers: MSD, Crane, Jacobs, Mallory, Holley, Etc. Prior to installation of your tachometer, check with the ignition box manufacturer for recommended tachometer signal location.
SERVICE
For service send your product to Auto Meter in a well-packed shipping carton. Please include a note explaining what the problem is along with your phone number. Please specify when you need the product back. If you need it back immediately mark the outside of the box “RUSH REPAIR,” and Auto Meter will service the product within two days after receiving it. ($10.00 charge will be added to the cost of “RUSH REPAIR.”) If you are sending the product back for Warranty adjustment, you must include a copy (or original) of your sales receipt from the place of purchase.
12-MONTH LIMITED WARRANTY
Auto Meter Products, Inc. warrants to the consumer that this product will be free from defects in material and workmanship for a period of twelve (12) months from the date of the original purchase. Products that fail within this 12-month warranty period will be repaired or replaced at Auto Meter’s option to the consumer when it is determined by Auto Meter Products, Inc. that the product failed due to defects in material or workmanship. This warranty is limited to the repair or replacement of parts in the Auto Meter instruments. In no event shall this warranty exceed the original purchase price of the Auto Meter instruments nor shall Auto Meter Products, Inc. be responsible for special, incidental, or consequential damages or costs incurred due to the failure of this product. Warranty claims to Auto Meter must be transportation prepaid and accompanied by a dated proof of purchase. This warranty applies only to the original purchaser of the product and is non-transferable. All implied warranties shall be limited in duration to the said 12-month warranty period. Breaking the instrument seal, improper use or installation, accident, water damage, abuse, unauthorized repairs, or alterations void this warranty. Auto Meter Products, Inc. disclaims any liability for consequential damages due to breach of any written or implied warranty on all products manufactured by Auto Meter.
FOR SERVICE SEND TO:
AUTO METER PRODUCTS, INC. 413 W. Elm St., Sycamore, IL 60178
815-899-0801
For Email:
Service@autometer.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>