SIGNATURE HARDWARE 944718 TOPPING Outdoor Wall Sconce Instruction Manual

June 13, 2024
Signature Hardware

SIGNATURE-HARDWARE-logo

SIGNATURE HARDWARE 944718 TOPPING Outdoor Wall Sconce

SIGNATURE-HARDWARE-944718-TOPPING-Outdoor-Wall-Sconce-
product

Product Usage Instructions

Before You Begin

We recommend consulting a professional if you are unfamiliar with installing electric fixtures. Signature Hardware accepts no liability for any damage to the faucet, plumbing, sink, countertop, or for personal injury during installation. Observe all local plumbing and building codes. Unpack and inspect the product for shipping damage.

Recommended Tools and Care and Maintenance

  • To clean, wipe with a damp cloth. Do not use abrasive cleaners or cleaners that contain alcohol.
  • Pour nettoyer, essuyer avec un chiffon humide.
  • Shut off the main power supply before cleaning the product or changing light bulbs. All glass is fragile. Use care when handling glass shades and bulbs.

Installation Steps

  1. Shut off the power at the circuit breaker and remove the old fixture, including the crossbar.
  2. Carefully unpack your new fixture and lay out all the parts on a clear area. Take care not to lose any small parts necessary forinstallation.
  3. Thread the 2 Mounting Screws (C) to the Mounting plate (E). You can adjust the length of the screws if necessary.
  4. Attach the Mounting plate (E) to the Outlet Box (G) (not supplied) by using 2 Outlet Box Screws (B).
  5. Adjunte la placa de montaje (E) a la caja tomacorrientes (G) (no incluida) usando 2 tornillos de caja tomacorrientes (B).
  6. Attach the Fixture (H) to the Mounting Plate by inserting the 2 Mounting Screws (C), and then secure with the 2 Cap Nuts (F).
  7. To prevent moisture from entering the outlet box and causing a short, use clear caulking (e.g., Indoor/Outdoor Silicone Sealant) to outline the outside of the fixture backplate where it meets thewall, leaving a space at the bottom to allow moisture a means toescape.

BEFORE YOU BEGIN

  • We recommend consulting a professional if you are unfamiliar with installing electric fixtures. Signature Hardware accepts no liability for any damage to the faucet, plumbing, sink, counter top, or for personal injury during installation.
  • Observe all local plumbing and building codes.
  • Unpack and inspect the product for shipping damage.
  • If any damage is found, contact our Customer Relations team via live chat at www.signaturehardware.com or by emailing support@siganturehardware.com.

GETTING STARTED

  • Ensure that you have gathered all the required materials that are needed for the installation.

CARE AND MAINTENANCE

  • To clean, wipe with damp cloth. Do not use abrasive cleaners or cleaners that contain alcohol.

CAUTION: Shut off main power supply before cleaning product or changing light bulbs. All glass is fragile. Use care when handling glass shades and bulbs.

RECOMMENDED TOOLS AND ACCESSORIES

SIGNATURE-HARDWARE-944718-TOPPING-Outdoor-Wall-Sconce-
fig-1

SAVE THIS MANUAL: RETAIN FOR CONSUMER’S USE.
READ THESE INSTRUCTIONS COMPLETELY BEFORE INSTALLING THE PRODUCT: FOR PRODUCT OR INSTALLATIO QUESTIONS PLEASE CALL CUSTOMER. SERVICE AT 1-800-221-3379.

INSTALLATION

  1. Shut off the power at the circuit breaker and remove old fixture, including the crossbar.
  2. Carefully unpack your new fixture and lay out all the parts on a clear area. Take care not to lose any small parts necessary for installation.
  3. Thread the 2 Mounting Screws (C) to the Mounting plate (E). (You can adjust the length of the screws if necessary.)
  4. Attach the Mounting plate(E)to the Outlet Box (G) (not supplied) by using 2 Outlet Box Screws (B).
  5. Now connect the electrical wires as follows: Connect the black wire from the fixture to the black house (hot) wire. Connect the white wire from the fixture to the white (neutral) house wire. Make sure all wire nuts are secured. You may wrap the connections with electrical tape. If your outlet has a ground wire (green or bare copper), connect fixture’s ground wire to it. Otherwise, connect fixture’s ground wire directly to the mounting plate using the green screw provided. Tuck the wire connections neatly into the junction box.
  6. Attach the Fixture (H) to the Mounting Plate by inserting the 2 Mounting Screws (C),and then secure with the 2 Cap Nuts (F).
  7. To prevent moisture from entering the outlet box and causing a short, use clear caulking (ie. Indoor/Outdoor Silicone Sealant) to outline the outside of fixture backplate where it meets the wall leaving a space at bottom to allow moisture a means to escape.

1.855.715.1800
signaturehardware.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Signature Hardware User Manuals

Related Manuals