SIGNATURE HARDWARE 440759 14 Inch Tall Barwell Single Light Instruction Manual
- June 13, 2024
- Signature Hardware
Table of Contents
SIGNATURE HARDWARE 440759 14 Inch Tall Barwell Single Light
Product Information
- Product Name: BARWELL
- SKU: 440758, 440759
- Description: The BARWELL is a lighting fixture that requires installation. It comes with a circular strap, outlet box screws, a front plate, a glass cup, and screws for securing the glass. The fixture supports a light bulb with a maximum wattage capacity of 60 watts (ST58 bulb).
Product Usage Instructions
-
Make sure you have gathered all the required materials and tools listed below:
- Light Bulb (ST58 60 watt maximum)
- Safety Glasses
- Wire Stripper
- Step Ladder
- Phillips Screwdriver
- Flathead Screwdriver
- Wire Cutters
- Electrical Tape
-
Thread the mounting screws (A) into the matching holes in the circular strap (B).
-
Secure the circular strap (B) to the outlet box using the outlet box screws (C).
Note: If you have electrical questions, consult your local electrical code for approved grounding methods.
-
1. After connecting the wires, carefully tuck them inside the outlet box. Raise the front plate (D) to allow the mounting screws (A) to protrude. -
Raise the glass (H) to the cup (F) and secure it with the screws (G).
-
Install a light bulb (not provided) into the socket. Make sure not to exceed the maximum recommended wattage capacity.
If you have any additional questions or need further assistance, you can visit our Help Center at www.signaturehardware.com for product and warranty information. You can also reach out to us through live chat or by emailing support@signaturehardware.com.
BEFORE YOU BEGIN
We recommend consulting a professional if you are unfamiliar with installing
lighting fixtures. Signature Hardware accepts no liability for any damage to
the faucet, plumbing, sink, counter top, or for personal injury during
installation.
Observe all local plumbing and building codes. Unpack and inspect the product
for shipping damage. If any damage is found, contact our Customer
Relations team via live chat at
www.signaturehardware.com
GETTING STARTED
Ensure that you have gathered all the required materials that are needed for the installation.
FOR YOUR SAFETY
WARNING: Be sure the electricity to the wires you are working on is shut of, either the fuse is removed or the circuit breaker is shut of. You don’t need special tools to install this fixture. Be sure to follow the steps in the order given. Under no circumstances should a fixture be hung on house electrical wires, nor should a swag type fixture be installed on a ceiling which contains a radiant type heating system. Read instructions carefully, if you are unclear as to how to proceed, consult a qualified electrician.
TOOLS AND MATERIALS
INSTALLATION
INSTALLATION (FIG. 1)
-
Thread the mounting screws (A) into the matching holes in the circular strap (B).
-
Secure circulars trap (B) to the outlet box with outlet box screws (C).
-
Connect he white wire from the fixture to the white wire from the outlet box and the black wire from the fixture to the black wire from the outlet box. Cover the two wire connections using the two provided wire connectors. Wrap the two wire connections with electrical tape for a more secure connection. Attach the grounding wire connections with electrical tape for a more secure connection. Connect the copper ground wires from the fixture and from the outlet box to the ground screw on the circular strap.
Note: If you have electrical questions, consult your local electrical code for approved grounding methods -
After wires are connected, tuck them carefully inside outlet box. Raise the front plate (D) allowing for the mounting screws (A) to protrude.
INSTALLATION (FIG. 2)
- Raise the glass (H) to the cup (F) and secure with the screws (G).
- Install light bulb (Not provided). Please do not exceed the maximum wattage capacity recommended on the socket.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>