JEGS 2014-2015 Direct-Fit Exhaust Kit Instruction Manual

JEGS 2014-2015 Direct-Fit Exhaust Kit

Product Information

• Product Name: OEM Exhaust System
• Part Number: 106-0102

Product Usage Instructions

1. Carefully read all instructions before installation.
2. Disconnect the vehicle’s battery before removing the OEM exhaust system to prevent electrical accidents and reset the computer if applicable to the vehicle.
3. Remove the existing exhaust system from the vehicle, only removing the parts that will be replaced.
4. Clean the existing flange with a wire brush to ensure proper sealing.
5. Attach item 2 to the existing exhaust using item 1 (nuts and bolts not included).
6. If you have a 12-13 model year, use item 7 and 6 with the resonator.
7. Attach item 5 to the existing isolators and item 2 using items 3 and 4.
8. Connect the slip-fit joint on item 2 with the clamps provided.
9. Ensure that the new exhaust is not contacting any portion of the underbody of the vehicle or drivetrain.
10. Tighten all clamps starting from the rear of the vehicle. Do not exceed 30 ft-lb when tightening the clamp. Check all clamps after driving 50 miles and retighten if necessary.

Warning:

• When working on, under, or around any vehicle, exercise caution. Allow the vehicle’s exhaust system to cool before removal, as exhaust temperatures may cause severe burns. If working without a lift, always consult the vehicle manual for correct lifting specifications. Always wear safety glasses and ensure a safe work area. Serious injury or death could occur if safety measures are not followed.
• BRExhaust recommends professional installation for all products.

Technical Support

For any technical support, please contact: 1-800-631-7271

• BRExhaust Address: 1901 Corporate Ctr, Oceanside, CA 92056
• Website: Visit www.brexhaust.com for more information.

BILL OF MATERIALS

1. 167588
2. 169507
3. 167602
4. 167860
5. 167722
6. 167744
7. 169522
   WARNING:
   When working on, under, or around any vehicle exercise caution. Please allow the vehicle’s exhaust system to cool before removal, as exhaust temperatures may cause severe burns. If working without a lift, always consult vehicle manual for correct lifting specifications. Always wear safety glasses and ensure a safe work area. Serious injury or death could occur if safety measures are not followed.

INSTALLATION INSTRUCTION

• STEP 1:
  (Carefully read all instructions before installation) Disconnect the vehicle’s battery before removal of the OEM exhaust system. This will prevent electrical accidents and will reset the computer if it applies to the vehicle. Remove existing exhaust system from the vehicle. Only remove parts that will be replaced. Clean existing flange with a wire brush to ensure proper sealing.

• STEP 2:
  Attach item 2 to existing exhaust with item 1 (nuts and bolts not included)

• STEP 2A:
  Use item 7 and 6 with resonator for 12-13 model year

• STEP 3:
  Attach item 5 to existing isolators and item 2 with items 3 and4

• STEP 4:
  Connect slip fit joint on item 2 with clamps provided

• STEP 5:
  Ensure new exhaust is not contacting any portion of the underbody of the vehicle or drivetrain.

• STEP 6:
  Tighten all clamps starting from rear of the vehicle. (DO NOT EXCEED 30FT-LB WHEN TIGHTENING CLAMP AND CHECK ALL CLAMPS AFTER 50 MILES. RETIGHTEN IF NECESSARY)

Technical Support

• 1-800-631-7271
• www.brexhaust.com

References

• MagnaFlow Exhaust, Mufflers & Cat Converters - Quality. Power. Sound.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>