A O Smith MT-4 Hot Water Dispenser User Guide
- June 13, 2024
- A O Smith
Table of Contents
A O Smith MT-4 Hot Water Dispenser
Product Information: RO Water Purifier, MAX4
The RO Water Purifier, MAX4, is a highly efficient water filtration system designed to provide clean and safe drinking water. It consists of three filters: a Particle filter, a Carbon filter, and a Reverse Osmosis (RO) membrane filter. Each filter plays a specific role in removing impurities and enhancing the taste of the water.
- Particle filter: This filter is responsible for removing suspended solids, rust, sand, silt, organic matter, and unpleasant smells from the water. It also prevents the crystallization of calcium and magnesium ions in the filtration system.
- Carbon filter: The Carbon filter eliminates odors, chlorine, chloramine, and other impurities that affect the taste of the water. It significantly improves the overall flavor.
- RO membrane filter: With a precision filtration of 0.0001m, this filter removes viruses, bacteria, trace metals, heavy metal ions, and pesticide residue. It ensures the water is safe and free from harmful contaminants.
The estimated lifespan of each filter is as follows
| Filter | Estimated Filter Life | Model |
|---|---|---|
| Particle filter | 8-12 months | MT-4 |
| Carbon filter | 8-12 months | CMF TW-303-700 |
| RO membrane filter | 40-48 months | MAX4 |
Product Usage Instructions: Filter Change
- Do not disconnect the power supply.
- Remove the front cover and wait for 1 minute to allow the system to depressurize. The light display will flash during this minute.
- When the display stops flashing, raise the handle of the filter to a horizontal position until you hear a click. Proceed to pull the filter out.
- Remove all three filters. Make sure to remove any packaging from the new filters before installation.
- Insert all three filters back into their respective slots, ensuring you hear a click for each filter.
- Once successfully installed, the relevant filter indicator light display will turn white.
- Close the cover by aligning the magnets at the top first.
- After replacing any of the filters, switch on the faucet and let the water run from the filter tap for 15 minutes before consuming the water. This will flush out any air or residual particles from the new filters.
NOTE
- If the filter indicator display does not light up in white after replacement, adjust the water purifier so that it is at least 2cm away from the sides of the housing cabinet. Then, remove the filter and reinstall it.
- If the faucet stops dispensing water after any filter replacement, switch off the faucet and check that the filter is properly connected.
FILTER REPLACEMENT
RECOMMENDED FILTER REPLACEMENT CYCLE
- The recommended filter replacement cycles of this water purifier are based on statistics of international average indicator.
- Local water quality and water consumption will affect the lifespan of each filter.
- If you notice a fault of blockage of the filter, please contact the authorised after-sales service department immediately.
- The filter lifespan is based on an estimation of ordinary household water consumption. The system is not designed to be installed in public places of high or commercial water consumption.
| Filter | Particles removed | Estimated filter life | Model |
|---|---|---|---|
| Particle filter | Suspended solids, rust, sand, silt, organic matter, smells, | ||
| prevents crystallization of calcium and magnesium ions in filtration system. | |||
| 8-12 months | MT-4 | ||
| Carbon filter | Removes odors, chlorine, chloramine and improves taste. | 8-12 | |
| months | CMF | ||
| Reverse Osmosis (RO) membrane filter | 0.0001μm precision filtration, removes | ||
| viruses, bacteria, trace metals, heavy metal ions and pesticide residue. | |||
| 40-48 months | TW-303-700 |
REPLACING THE FILTER
- Do not disconnect power supply. Remove front cover and wait 1 minute for the system to depressurize. The light display will flash in this minute.
- When the display stops flashing, raise the handle of the filter to a horizontal position. You will hear a click. Proceed to pull the filter out.
- Remove all three filters. Replace affected filters, remember to remove all packaging. Insert all three filters back into the slots, ensuring you hear a click.
- When successfully installed, the relevant filter indicator light display will turn white. Proceed to close the cover, aligning the magnets at the top first.
After replacing any of the filters, switch on the faucet and let the water run from the filter tap for 15 minutes before consuming the water.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>