Contour RM-RED PLUS-WL Roller Mouse Red Plus Wireless User Manual
- June 13, 2024
- contour
Table of Contents
Contour RM-RED PLUS-WL Roller Mouse Red Plus Wireless
Box Contents
- RollerMouse Red plus Wireless
- Two short keyboard risers
- Two long keyboard risers
- Wrist rest
- Wrist rest removal key
- Dongle (Wireless receiver)
- USB 2.0 cable adapter
- USB to Micro USB cable / Charging cable
- User Guide
RollerMouse functions
- A. Rollerbar
- B. Cursor speed / Battery level indicator (LED)
- C. Copy
- D. Paste
- E. Left-click
- F. Right-click
- G. Scroll wheel
- H. “One Touch” double-click
- I. On-Off switch
- J. Dongle storage compartment
For additional mouse features and specific Mac settings, please download our driver at http://support.contour-design.co.uk.
Keyboard Positioning
Before plugging in the unit, take a moment to check the height and angle of
your keyboard, and find the arrangement that’s most comfortable for you. Use
the risers to achieve the correct angle and height regardless of the type of
keyboard you are using. The spacebar on your keyboard should come just above
your rollerbar. To achieve a proper ergonomic position, the front edge of the
keyboard should be as close as possible to the rollerbar. Balance Keyboard is
designed specifically for the roller mouse. The keyboard sits level with the
rollerbar and can be easily adjusted to a positive, neutral, or negative tilt.
Inserting the Keyboard Risers
Fit the end of the riser 2 into the slot on the back of the RollerMouse
Red.
Adjusting Risers
Line up the short and long risers 2 and 3 then press the two
parts together until you hear them snap into place.
Power Switch
The power switch can be found on the underside of the RollerMouse Red. Before
using the RollerMouse Red please make sure the power switch is set to the ON
position. Turning off the device is only necessary for long-term storage or
during travel.
Connecting to a computer
Plug the wireless receiver or the charging cable into the computer’s USB
port. Allow your computer a few seconds to automatically install.
Using the rollerbar
The rollerbar A provides two functions:
- Pressing down on the rollerbar performs a left click.
- Moving the rollerbar from side to side and up and down performs cursor movement.
Charging
To charge your RollerMouse Red remove the dongle from the extender cable and
plug the Micro USB into the RollerMouse Red. Your RollerMouse Red will charge
in 6 hours and you may continue to use your RollerMouse Red while it charges
.
Pairing
With the RollerMouse Red in close proximity to the dongle, hold left-click
1 , right-click 2 and the cursor speed 3 buttons at the same time
until the LED indicator turns green and pulses twice in succession.
Rollerbar Click Force Adjustment
Click force refers to the level of resistance when clicking the rollerbar.
To change the click force, press and hold both the E and the B
buttons, the LED light will show the current click force setting. While
continuing to hold button B release button E , and click the E
button in succession. Release both buttons once the desired click force
tension has been reached.
Note: The rollerbar click function can be turned off using the a bove
adjustment method, by moving the scroll wheel until all LEDs are lit.
Battery Level
- Your RollerMouse Red comes pre-charged and has an expected battery life of up to 3 months with average daily use.*
- RollerMouse Red has a built-in rechargeable battery. To see the battery level on your device, press the cursor speed button once. The RollerMouse will first display the current cursor speed (DPI), then display the current battery level.
- If your RollerMouse Red is running low on battery, the center LED light will start blinking red.
- To charge your battery, plug the charging cable into your RollerMouse Red and connect it to a USB port on your computer (see page 5). The RollerMouse Red will charge in 6 hours and you may use your RollerMouse Red as it charges.
*Battery life may vary based on user and computing conditions.
Change cursor speed hastighet
Press the Cursor Speed button B to cycle through cursor speeds. There
are ten-speed selections that range from slow (600 DPI) to fast (2400 DPI).
Speed can be identified by the LED lights as shown.
Operating System
RollerMouse Red as 3 modes. PC-Mode, Mac-Mode and HID-Mode. The default setting on your RollerMouse is PC-Mode.
Press and hold the B button and click the C button to see the LED lights flash for the respective mode. To toggle between the other available modes, hold the B button, release the C button and click the C button in succession. Release both buttons once the desired mode has been reached.
Different Mode Settings
Alternate Functions for the Double Click Button
There are 5 alternate functions for the Double Click Button. Each function
is indicated by the position of the red LED within the Cursor Speed/Battery
Level Indicator.
To change the double-click function to one of the other available functions,
press and hold the B button and click the H button to see the LED
lights display the respective mode. To toggle between the other available
modes, hold the B button, release the H button and click the H
button in succession. Release both buttons once the desired mode has been
reached. 
*The freese click function can be used to recenter or reposition your rollerbar without moving the cursor. An example of a situation where freeze click would be usefull is in a multimonitor setup where the cursor has landed on the third monitor and the user wishes to center the rollerbar to better work that monitor.
Wrist rest
We recommend that you use the wrist rest 4 , however, if for any reason
you would like to remoe the wrist rest, lift the front edge of the RollerMouse
and rest it in your hand. Fit the wrist rest removal key 5 into the slot
at the end of the unit and twist the key. To install the wrist rest after
removal, snap it nito the slot on the front edge of your RollerMouse Red
.
FCC Statement
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
IC Statement
This device complies with Industry Canada’s license-exempt RSSs. Operation is
subject to the following two conditions:
- This device may not cause interference; and
- This device must accept any interference, including interference that may cause undesired operation of the device.
The term “IC: “ before the certification/registration number only signifies that the Industry Canada technical specifications were met. This product meets the applicable Industry Canada technical specifications.
Warranty
If there is a functional defect due to faulty manufacturing, we will replace
the product. This warranty does not cover damage that results from misuse of
the product.
Attention! If you attempt to dismantle your RollerMouse, you will
invalidate your warranty.
For more information please visit:www.contour-design.co.uk
Contour Design Nordic A/S
Borupvang 5B, st.tv. 2750 Ballerup Denmark
Telefon: +45 70 27 02 27
E-mail: info@contour-design.com
Tested to comply with FCC and IC standards.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>