legrand 67696 Connected Module for Gate and Garage Door Instruction Manual
- June 13, 2024
- Legrand
Table of Contents
legrand 67696 Connected Module for Gate and Garage Door
Product Information
- Power Input: 110-240 Vac
- Frequency: 50/60 Hz
- Wire Sizes: 1 x 2.5 mm2, 2 x 1.5 mm2
- Response Time: 0.5 seconds
- Model Number: ZLS24
- Wireless Technology: RF
- Diameter: 7mm
- Maximum Current: 1A
- Country of Origin : France
Product Usage Instructions
- Ensure the power input is compatible with your local voltage (110-240 Vac).
- Connect the wires using the appropriate wire sizes (1 x 2.5 mm2 for one wire, and 2 x 1.5 mm2 for two wires).
- Wait for the device to respond within 0.5 seconds after activation.
- The product model number is ZLS24.
- If the device supports wireless communication, it uses RF technology.
- The product has a diameter of 7mm.
- Ensure the current does not exceed the maximum limit of 1A.
- This product is manufactured in France.
- The device has three connection points labeled S1, C, and S2.
- The distance between the connection points S1 and S2 is 10mm.
- The device has four additional points labeled NL, and numbers from 3 to 10.
- Refer to the user manual for specific instructions on using the additional points.
Hardware
Requires you to buy and install the ” with Netatmo” connected starter pack first.
- Module Control
- Gateway power outlet Control
- Mobile Control Gateway
Pack contents
- Connected module for gate and garage door
- Sensors installation accessories x2
- Sensorsx2
- Magnetx2
Characteristics
Wiring Instruction
Before you start: wiring precautions
If you plan to install connected control modules, read the following
precautions:
To control a garage door or a gate, only use the following products :
Wireless control for shutters (with or without battery}.
Not included in this pack.
Example : Plexo shutter control Cat.No O 698 73L
Not included in this pack. Example :
Wireless remote control Cat.No O 676 95
Necessary safety precautions
Switch off the power at the main circuit breaker
Make sure that the power is off before continuing with the installation
Installation of the connected module for garage door and gate
Install the connected module into a weatherproof box 105x105mm (eg Plexo O
920 22 not included in this pack)
- S1 : Closed position sensor
- S2 : Open position sensor
- C : Common terminal for S1 and S2 sensors
- N (neutre) = bleu
- N (neutral) = blue
- L (phase) = tout sauf bleu et vert/jaune
- L (live) : all except bleu and yellow/green
- Frequency bands: 2.4 – 2.4835 GHz
- Power level: < 100 mW
Installation is possible inside a weatherproof 80x80mm by removing the 2 fixation wings
Power the wired products
Mandatory installation steps:
Turn the power back on at the main circuit breaker.
All wired products must be supplied with power simultaneously.
The indicator lights on the products that you have wired turn red.
Start configuration of the connected module manually or via Home + Control
App
Manual process : open the network to add the connected module
- Module Control
- Gateway power outlet Control
- Mobile Control Gateway
-
Press the configuration button of the Module Control until its light briefly turns green, and then stop pressing.
-
Take the wireless master switch near to the gateway power outlet Control and press the middle of the wireless switch until its light briefly turns green, and then stop pressing.
-
Press the configuration button of the Mobile Control Gateway until its light briefly turns green, and then stop pressing.
-
The LED indicator goes to green.
-
Finalize the configuration
-
To finalize the installation, press briefly the configuration button of the Module Control or the Mobile Control Gateway or in the center of the Home/ Away wireless switch.
-
All the indicator lights on the products switch off.
Application Home + Control Home + Control App
-
Make sure you have previously installed a connected starter pack “with Netatmo” and downloaded the Home + Control App
-
To add your connected product to your connected installation, you should follow the instructions in the Legrand Home+ Control application (Settings/Add a new product section)
Installation Instruction
Installation on a garage door (example)
-
Sensor S1 : closed
-
Installation accessories
-
Mounting of Sensor S1 (closed position) on the accessory, fix the sensor using the sticker .
The accessory is installed on the fixed part of the rail. -
Fix the magnet to the moving part (sliding arm).
-
It will have to position itself in front of each of the two sensors 51 and 52 depending on the opening or closing.
-
For the correct positioning, see paragraph.
Recommended : finalize installation with screws (not delivered)
Installation accessories : fix the accessories on the rail with a sticker (not delivered)
Cut the installation accessories in order to adjust them perfectly
Installation on a sliding gate (example)
Mounting the installation accessories on the gate motor and installation of the sensor S1 on the accessory*
Mounting the installation accessories on the gate motor and installation of
the sensor S2 on the accessory*
Recommended : finalize installation with screws (not delivered)
Installation on a swing gate (example)
-
Weatherproof Plexo box (not included in this pack)
-
Mounting of the weatherproof box and connected module close to the gate motor
-
Mounting the installation accessory on the gate motor and installation of the sensor S1 on the accessory •
-
Recommended : finalize installation with screws (not delivered)
Help for the correct positioning of sensors
The orange LED on your connected module indicates incorrect positioning of the
sensor up or down with its magnet.
Please approach the sensor until the orange LED turns off to optimize the
functioning
- The orange LED of the connected module is ON
- The LED of the module is OFF
- For the module to operate optimally, the motorized configuration must be configured in step-by-step mode, described below.
Recommended behavior of the motor when the door is closed:
- Press the button on your garage door or gate remote to open the door.
- While the door is opening, pressing the button on the remote control causes the door to stop.
- Further pressing of the button on the remote control causes the door to close.
If your motorized installation does not respect this behavior, it is
recommended to modify it by following the motor manufacturer’s instructions.
To add a connected product to your connected installation, you should follow
the instructions:
- in the Legrand Home+ Control application (Settings/Add a new product section)
- or consult the user manual on legrand.com
www.legrand.fr/reference/067696
www.legrand.com
LEGRAND – Pro and Consumer Service – BP 30076
87002 LIMOGES CEDEX FRANCE• www.legrand.com
Safety instructions
This product should be installed in compliance with installation rules,
preferably by a qualified electrician. Incorrect installation and/or incorrect
use can lead to risk of electric shock or fire. Before carrying out the
installation, read the instructions and take account of the product’s specific
mounting location. Do not open up, dismantle, alter or modify the device
except where specifically required to do so by the instructions. All Legrand
products must be opened and repaired exclusively by personnel trained and
approved by Legrand. Any unauthorized opening or repair completely cancels all
liabilities and the rights to replacement and guarantees. Use only Legrand
brand accessories.
SIMPLIFIED EU DECLARATION OF CONFORMITY
The undersigned, Legrand
declares that the radio-electric equipment referred to in these instructions
complies with directive 2014/53/EU. The full text of the EU declaration of
conformity is available on the following website :
www.legrandoc.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>