EMOS ZS2941 LED Floodlight SMD Plus Pir Sensor Instruction Manual
- June 4, 2024
- EMOS
Table of Contents
LED Floodlight SMD + PIR SENSOR
ZS2911/ZS2921
ZS2931/ZS2941
ZS2941 LED Floodlight SMD Plus Pir Sensor
Type| input Voltage| Max.
Power| Max.
Power| Life
Span| Dimensions| Weight| Maximum Projected
Area
---|---|---|---|---|---|---|---
ZS2911| 220–240 V AC
50 Hz| 10.5 W| 25 000 h| 800 lm| 105 × 143 × 64 mm| 0.20 kg| 0.01 m²
ZS2921| 20 W| 25 000 h| 1 600 lm| 135 × 165 × 64 mm| 0.23 kg| 0.02 m²
ZS2931| 30.5 W| 25 000 h| 2 600 lm| 165 × 185 × 64 mm| 0.36 kg| 0.03 m²
ZS2941| 51 W| 25 000 h| 4 300 lm| 210 × 217 × 64 mm| 0.50 kg| 0.03 m²
LED reflector is designed for indoor and outdoor use to be mounted on a firm
ground.
Ingress Protection: IP54 – for outdoor use
PIR sensor – specification:
Time-delay: min. 10 s ±5 s – max. 10 min ±1 min
Detection angle: 120°
Ambient light: 5 lux –> 2 000 lux (adjustable)
Detection distance: 5–10 m
Detection motion speed: 0.6–1.5 m/s
PIR sensor setting:
The detection field is possible to be set by moving the motion sensor switch
to the left and to the right.
Adjustment of the ambient light (sensitivity)
You can choose at what luminosity will the sensor go on by button A (see
picture no. 4).
Time-delay
You can set the time delay of the lamp by a button B (see picture no. 4)
Detection range The distance at which the sensor responds to movement can be
set using control C.
Mounting
Mount the lamp firmly onto a solid basis, for example, a wall (fig. 1, 2, 3).
Installation height 2.3–3 m.
Connect a power cable for connection to a 220–240 V~power network.
The cable must not be plugged into the power network during the installation
of the spotlight.
Direct the reflector as shown on fig. 1 and 2.
L – brown – live wire
G – green&yellow – earth wire (ground)
N – blue – neutral wire
Maintenance instructions:
Before maintenance, switch off the lamp and wait until it is cooled.
Clean it with a soft moistened cloth.
Never submerge the lamp in water or other liquids.
During maintenance, observe general rules for occupational safety, and be very
careful.
WARNING
- The reflector is designed entirely for firm mounting.
- Before connecting to the 220–240 V~ make sure that the connecting wire is not under voltage. This operation can be carried out only by an authorized person.
- Respect a minimum distance of 1 m between the appliance and the object or surface which you wish to lighten.
- If you place the reflector below the roof, keep the minimum 0.2 m distance measured from the upside of the reflector to the bottom of the roof.
- Do not use the reflector without the protection glass.
- The protection from dangerous contact voltage is ensured by „earthing“.
- The external flexible cable or cord of this luminaire cannot be replaced; if the cord is damaged, the luminaire shall be destroyed.
- The light source of this luminaire is not replaceable; when the light source reaches its end of life the whole luminaire shall be replaced.
- Terminal block not included. Installation may require advice from a qualified person.
- Terminal block for connection of power supply: 3 terminals screw-less type, rated for cross-section range including1 mm2 and voltage min 230 V.
- Type Z attachment
- Caution, risk of electric shock ****
Do not dispose of domestic waste. Use special collection points for sorted
waste. Contact local authorities for information about collection points. If
the electronic devices would be disposed on landfill ll, dangerous substances
may reach groundwater and subsequently the food chain, which it could affect
human health.
EMOS spol. s r.o. declares that the ZS2911, ZS2921, ZS2931, and ZS2941 is in
compliance with the essential requirements and other relevant provisions of
the Directive. The device can be freely operated in the EU. The Declaration of
Conformity can be found at http://www.emos.eu/download.
This product contains a light source of energy efficiency class F
Servis: EMOS SI, d.o.o., Rimska cesta 92, 3311 Šempeter v Savinjski dolini,
Slovenija
tel: +386 8 205 17 21
e-mail: [email protected]