LIFESPAN KIDS LKCH-TEDV2NT KIDS Wooden Cubby House User Manual

USER MANUAL
Wooden Cubby House

LKCH-TEDV2NT KIDS Wooden Cubby House

WARNING: The disassembled product may contain small parts which pose a choking hazard to children under 3.

IMPORTANT:
The owner’s manual contains safety, assembly, use and maintenance instructions. This product must be assembled by an adult who has read and understood these instructions. Keep the packaging away from children and dispose of all packaging before use. For the installer and your children’s safety, it is important to fully read and understand the instructions and safety hazards before commencing the assembly of the product.
NOTE:
This manual should not be used to guide your purchasing decision. Your product, and the contents inside its carton, may vary from what is listed in this manual. This manual may also be subject to updates or changes. Updated manuals are available through our website at www.lifespankids.com.au.

GENERAL SAFETY INSTRUCTIONS

NOTE: This product is intended for outdoor domestic use only.
1.1 DANGER FOR CHILDREN
WARNING: No eating while using the product at the same time.

• Children do not recognize the potential dangers of this product. The unassembled product must be stored out of reach of children and pets.
• This product may only be used with adult supervision at all times.
• The packaging material is not suitable for children due to choking and suffocation hazards.

1.2 RISK OF INJURIES

• Do not use the product if it is damaged or defective. If it is damaged or defective, please contact a qualified technician.
• Check the product before each use. Defective parts must be changed immediately as they can impair the function and the safety of the product.
• No more than 2 children to use the product at the same time.
• Use the product only on even and non-slipping surfaces. Never use it near water and keep sufficient space around for safety.
• Beware of moving parts such as the doors or windows, which could catch your arms and legs. Do not place any objects or body parts in the product’s openings.

1.3 PRODUCT DAMAGE

• Do not make alterations to the product. Only use original spare parts. Qualified technicians should only carry out repairs – improper repairs can lead to danger for the user. Use this product only as described in this manual.
• Moving parts with hinges can be damaged if they are slammed continuously. Ensure users are closing doors or windows without force and during windy weather, it is best to secure these areas.

1.4 ASSEMBLY ADVICE

• The assembly of the product must be done carefully and by an adult. If in any doubt, ask technically qualified personnel.
• Before you start with the assembly, read the instructions carefully.
• Remove all packaging materials and lay down all parts in an open space. This gives you an overview and simplifies the assembly procedure.
• Check with the parts list that all parts are available. Dispose of the packaging material when the assembly is completed.
• Beware that when using tools or doing technical work, there is always a risk of injuries. Assemble the product with care.
• Create a danger-free environment; for example, do not let tools lay around the workspace. Store the packaging material in a way that cannot cause any danger
• After installing the product according to the instruction manual, ensure all screws, bolts, and nuts are correctly installed and tightened and that all joints are secure.
• Your play structure must be installed on a flat horizontal surface with a minimum of 2m between it and any structure or obstacle such as a fence, garage house, tree branches, cloths lines, or electric cables.
• Modifications made to the original product shall be carried out according to the instructions of the manufacturer.
• The product must always be used in a well-lit area.
• Do not place anything under the product.
• Use gloves during assembly and disassembly.
• Outdoor products can be anchored for extra stability and to avoid movement in hazardous weather (e.g steel bars or pegs in the ground).
• In certain areas during winter, snow buildup and low temperatures can damage the product. We recommend you remove the snow to build and visually inspect to ensure the integrity of the entire product.
• We strongly recommend visual inspections every 3 months to ensure the integrity of the entire product. Replace any parts as necessary.

SAFETY INSTRUCTIONS

• The safety instructions of the product should always be considered and obeyed.

• No clothes with hooks or loose parts should be worn or carried during product usage in order to avoid hooks getting caught and causing injury.

• Strong winds can result in the product being blown away or damaged. If strong winds are predicted the product must be disassembled and moved to a sheltered area or efficiently anchored down.

• Moving the product whilst assembled may affect the integrity of the frame. Should it be necessary to move the product, please consider the following:
  1. Force to be evenly spaced around the frame to lift the product off the ground
  2. The product must be carried horizontally
  3. Use caution whilst moving as it could bend the product frame.

• Users should be familiar with the assembly manual. This manual contains assembly guidance; selected precautionary measures as well as recommendations for servicing and maintenance of the product, in order to ensure a secured and fun use of the product.

• It is the responsibility of the owner or the supervisor to guarantee that all users of the product are informed sufficiently of all warning references and safety instructions.

For the supervisor
The supervisor’s role is to make sure users are aware of all safety precautions and that these precautions are enforced. When a supervisor is not available, the product may be disassembled or covered to limit access.

• The product can be only used if it is in good condition, and worn or damaged parts should be replaced.
• Objects, which could be dangerous to the user, should be away from the product.
• Avoid unauthorized and unsupervised use of the product.
• Do not use the product under influence of alcohol or drugs (incl. medicines).
• Do not use the product as a jumping platform for other articles.

Consumer Information Sheet for Playground Surfacing Materials
The US Consumer Product Safety Commission (CPSC) estimates that about 100 000 playground equipment-related injuries resulting from falls to the ground surface are treated annually in US hospital emergency rooms. Injuries involving this hazard pattern tend to be among the most serious of all playground injuries and have the potential to be fatal, particularly when the injury is to the head. The surface under and around playground equipment can be a major factor in determining the injury-causing potential of a fall. It is self-evident that a fall onto a shock-absorbing surface is less likely to cause a serious injury than a fall onto a hard surface. Playground equipment should never be placed on hard surfaces, such as concrete or asphalt, and while the grass may appear to be acceptable, it may quickly turn to hard- packed earth in areas of high traffic. Shredded bark mulch, wood chips, fine sand, or gravel are considered to be acceptable shock-absorbing surfaces when installed and maintained at a sufficient depth under and around playground equipment.

Table B.1 Lists the maximum height from which a child would not be expected to sustain a life-threatening head injury in a fall on to four different loose- fill surfacing materials if they are Installed and maintained at depths of 150 mm, 225 mm, and 300 mm.
Table B.1 Fall height in millimeters from which a life-threatening head injury would not be expected.

However, it should be recognized that all injuries due to falls cannot be prevented, no matter what surfacing material is used. It is recommended that a shock absorbing material extend a minimum of 1 800 mm in all directions from the perimeter of stationary equipment such as climbing frames and slides. However, because children may deliberately jump from a moving swing, the shock absorbing material should extend in the front and rear of a swing a minimum distance of twice the height of the pivot point measured from a point directly beneath the pivot on the supporting structure. This information is intended to assist in comparing the relative shock-absorbing properties of various materials. No particular material is recommended over another. However, each material is only effective when properly maintained. Materials should be checked periodically and replenished to maintain the correct depth as determined necessary for the equipment in question. The choice of a material depends on the type and height of the playground equipment, the availability of the material in a particular area, and its cost.

ASSEMBLY INSTRUCTIONS

|
---|---
|
|

3.1 SET UP

|
---|---

STEP 4 – Stool
Step 1. Attach No. 21 to No. 24 and No. 23, and use screws F x 6. On the other side the same.
Step 2. Attach No. 22 to the stool leg as shown, and use screws F x 8.
Step 3. Attach stool to the wall panel as shown, use hardware G, screws D x 8.

|
---|---

MAINTENANCE

WARNING: Please keep for future reference.

We recommend regular maintenance to be conducted at the beginning of each season as well as at regular intervals during the usage session for your play equipment to ensure all main parts/fixings are tightly secured, well-oiled, and intact to avoid failure, injury or hazards.

GENERAL ADVICE
It is of particular importance that this is followed at the beginning of each season as well as at regular intervals during the usage season.

• Check the accessories monthly as well as the play equipment’s structure to prevent falling risks.

• Check and retighten screws, bolts, and all other hardware elements as necessary.
  a. Do not over-tighten to avoid damaging the thread or cracking the surrounding wood.

• Check all coverings and bolts for sharp edges and replace them when required.

• Lubricate all moving metallic parts.

• When signs of oxidation and/or rust appear on various metallic parts of your equipment, sand rusted areas and tubular members and repaint using a non-lead-based paint
  when required.

• Where applicable: check swing seats, chains, ropes, and other means of attachment for evidence of deterioration.

• ]Replace when required in accordance with the owner’s manual.

If your play structure is disassembled, be sure to clearly mark any attached metal plates to prevent accidents. Check all bolt covers and sharp edges and replace them if necessary.
For longer accessory life, we suggest storing them during the winter.

WOOD ADVICE

Our products are manufactured from premium timber. Great care is taken in selecting, machining, and treating the timber before it is sold to you.

1. Inspect wood parts monthly. The grain of the wood sometimes will lift in dry periods causing splinters to appear. Light sanding may be necessary to maintain a safe environment. Treating your product with protection (water-based acrylic paint or water-based stain recommended) after sanding will help prevent severe checking/splitting and other weather damage.
2. We have applied a waterborne translucent stain to your unit. This is done for color only. Once or twice a year, depending on your climate conditions, we highly recommend applying a new layer of protection in the form of water-based acrylic paint or water-based stain to get the optimum life from your product. Prior to the application of sealant, lightly sand any “rough” spots on your set. Please note this is a requirement of your warranty. Bear in mind that timber is a natural product and may experience changes throughout the course of its life. It may:

• Develop opening/checks (splits, gaps, slits, apertures, cracks) along the line of the grain due to moisture & temperature changes.
• Colour fades as the timber reacts with sunlight.

MORE INFORMATION ON WOOD SPLITS
Each Lifespan Kids Timber Play Equipment is designed and built with tolerances to account for wood splits. All timber components are dried, temperature treated and specified to the right size to ensure that the structural integrity of your play equipment will not be compromised from normal weathering. Most wood splits will never become large enough to affect the reliability and strength of your play equipment.
Please note that in dryer seasons, wood splits will appear more often, and often in wet seasons, you’ll find that these wood splits will mostly disappear as the timber collects moisture and swells up. These are normal cycles
In the unlikely event you feel that a part has a possible fault in the timber, please contact Lifespan Kids immediately with pictures of the parts so they can be reviewed. Please refer to Page 15 to get in touch with us.

For more information: www.lifespankids.com.au/natural- timber

WARRANTY

AUSTRALIAN CONSUMER LAW
All of our products come with a guarantee or warranty from the manufacturer. In addition, they come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage.
You are entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. Full details of your consumer rights may be found at www.consumerlaw.gov.au.

SUPPORT
Please send all warranty and support inquiries through our ticketing system via the website: www.lifespankids.com.au/warranty- form
Our goods come with guarantees that cannot be excluded under the ACL. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if goods fail to be of acceptable quality and the failure does not amount to a major failure.

www.lifespankids.com.au

Head Office and Customer Service:
Global Fitness and Leisure Pty Ltd
23-25 Maygar Blvd
Broadmeadows, VIC 3047
Australia
PH: 1300 169 600

References

• Home | Consumer Law
• Lifespan Kids Official Store | Trampolines, Cubby Houses, Outdoor Play

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>