ATU 2611991 Parking Sensors Without Drilling User Manual
- June 13, 2024
- ATU
Table of Contents
NO DRILL PARKING
SENSORS
2611991 Parking Sensors Without Drilling
ART: 2611991-NO3202
Manual and security information
USER MANUAL
FOREWORD
We thank you for choosing our product. It is designed for you according to
the highest quality standards.
Please read the operation manual carefully before using and operating the
unit. Heed all warnings.
If the device is passed on to another person, this manual must be handed over
to the user along with it. Please keep this manual handy for future reference.
INTENDED USE
Electromagnetic parking sensor consists of sensor antenna, control box and
buzzer. It is very easy to install. This system detects the distance between
the car body and obstacles in the back with sensor antenna installed on the
rear bumper of car.
With the change of alarm sound, the product can detect the safe area
correctly. Bumper damage is minimized as NO hole needs to be drilled! It is
best choice for the safety of your car.
SAFETY INSTRUCTIONS
Read this user manual carefully before using the product. If you do not observe the instructions on proper handling in this manual, we shall not be held liable for any resulting personal injury or damage to property.
- Please install this product within the voltage range specified. Failure to do so can cause electric shock or product malfunction.
- Electric shocks or product malfunctions may occur if this product is installed incorrectly.
- If smoke or a burning smell is detected, disconnect the system immediately.
- When you install the system, the car should be in powered off state.
- Do not locate the control unit near to other interference such as exhaust pipe or other wires.
- Where the power cable may touch a metal case, cover the cable with a friction tape. A short circuit or disconnected wire may cause a fire.
- Feed as much cable as possible into the vehicle and clamp it securely. This reduces the possibility of the cable being hooked or snagged.
- Keep all cables away from hot or moving parts and electrical noisy components.
- The performance may be affected in the following situations: heavy rain; the gravel road, bumpy road, sloping road and bush; very hot, cold or moist weather. Other ultrasonic or electric wave, e.g. the DC/AC switch or 24V/12V switch may affect the performance of the system.
- Test the system to make sure it works well before using.
- This system is a reversing aid and themanufacturer takes no responsibility for anyaccidents caused after the kit is installed.
PARTS LIST
-
Spade
Connector -
Sensor
Antenna -
Protect Wire
Ring -
Cable Tie
-
Sticker
-
Buzzer
-
Control Box
INSTALLATION AND TEST
Connection diagram of parking sensor
Before you install
Temporarily unroll the tape (sensor antenna) until the entire inside of the
bumper has been covered from side to side, do not wrap the sensor antenna
around the sides of the bumper cover. Do not remove the backing paper from the
adhesive side at this time.
Layout the control box and buzzer where you intend to install, then check the
followings:
- Is the length of the wires sufficient to complete the installation on the vehicle?
- Is there a clean, smooth surface behind the bumper that permits mounting with enough clearance to attach the antenna foil? Keep the sensor antenna away from any metal parts.
- Always clean the inside of the bumper cover before installing the antenna.
- Is there a suitable, smooth surface to mount the control box and buzzer?
Install inside the bumper cover
- Thoroughly clean the inside surface of the bumper with the wet or alcohol wipes to ensure that the foil tape will properly adhere to the plastic surface.
- Take the end of the antenna foil with the spade connector and peel a few of the backing paper off.
- Apply the end of the antenna foil with the spade connector near the area where the black wire will come through.
- Adjust the antenna foil to line up across the inside of the bumper cover, then continue to pull the backing paper from the antenna foil as you press the antenna foil against the bumper cover.
Testing
Vehicle’s engine must be OFF and the parking brake must be engaged.
- Turn the vehicle’s ignition key to ON position, but do not start the engine.
- Place the vehicle’s transmission in reverse gear.
- Stand about 1.8m away from the bumper and slowly approach the vehicle.
- At distances from 70 to 40 cm, you will hear Bi…Bi…. At distances from 40 to 20 cm, you will hear BiBi….
TECHNICAL DATA
| Rated voltage | 12 V |
|---|---|
| Rated current | 200 mA |
| Detecting distance | 0.3-1.0 m |
| Ultrasonic frequency | 2 KHz |
| Operating temperature | -20 °C ~ +70 °C |
**** This product meets all the basic EU regulatory requirements relevant to it.
****Selective collection of waste electrical and electronic equipment.
Electrical equipment must not be disposed of with household waste.
Pursuant to European Directive 2012/19/EU on waste electrical and electronic
equipment, and its transposition into national law, waste electrical equipment
must be collected separately and disposed of in designated collection points.
Contact the local authorities or the vendor for advice on recycling.
NORAUTO
Distributed by
Dr.-Kilian-Str. 11, D-92637 Weiden i.d.OPf Deutschland
www.norauto.com
www.atu.eu
Made in P.R.C 23V0
Documents / Resources
| ATU
2611991 Parking Sensors Without
Drilling
[pdf] User Manual
2611991 Parking Sensors Without Drilling, 2611991, Parking Sensors Without
Drilling, Sensors Without Drilling, Drilling
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>