Shenzhen Lepson Technology RF433 Remote Control User Manual

Shenzhen Lepson Technology RF433 Remote Control

Warning Notice.

Please Read the manual carefullv before use it.

• Caution, Avoid looking directly at the laser light
• Do not look at the laser light with a telescope or other optical equipment.
• Class II laser light product, EN 6082.S Max. rating power. Wavelengths 535-650nm
• Avoid exposure, laser radiation is emitted from this aperture.
• IP65 rating only: Do not submerge i_n water; can be used outside on rainy days.
• Keep laser light projection 0.5 meter away from flammable material.
  Under sub-zero temperatures it can take a few minutes until the laserlight lights up fully

Technical Data

• Voltage supply
  • Mains adapter: I 00 – 240 V~ 50/60 Hz
  • (I x button cell, CR2025 / CR2032 type)
• Range of RC: 10-15 meters
• Mains cable length: 3 metres
• Operating temperature: -30°C to 30°C
• Power P: 50mW@535nm Max. ;100mW@650nm Max.
• Wavelengths: A 535nm (green)/ A 650nm (red)
• irradiance: < Im W/m’
• Laser class: 2acc. to IEC 60825-l:2014
• IP rating, adaptor IP44, product IP65

Setting up the laserlight

1. Unpack the rtems supplied and remove all protective films that may be present. Check all parts for possible transport dam­age. If you should find any transport damage, do not use the article(!), but contact the customer service department imme­diately.
2. By pressing the buttons of the re mote control, you can call up the following functions:

• I: On button
• 2: Offbullon
• 3: Static,AUTO,Flash Tiuee different mode optional
• 4: Color select but1011
• 5: Speed control buttion,fast or slow optional
• 6: Timer fhnction:0.5/3/5/8/10 hours optional,STOP for cancel Timer
• 1l1is is on RF remote control, for best use point the remote ot the housing unit from a distance of 10-15 meters
• For first use open the ba11ery compartment and remove the tab preventing connection of the battery during transportation.
• Batten model: 3 volt CR2025 f CR2032

Changing the Battery of the Remote Control

1. The battery compartment is located on the narrow side of the remote control. Pull it out as shown.
2. Take the used battery out and insert a 3V battery of the CR2025 / CR2032 type. t The positive pole must be facing upwards
3. Push the battery compartment back into the remote control to the limit stop.

Distance and Coverage:

Helpful Hints:

• The lieht is intended to ooerate from -30° C to 30° C. At lower temperatures, the laser light may take up to ten minutes to wam1 up and reach its foll projection strength.
• This appliance can be used by children from the age of 8 and above and persons with reduced physical, sensorv or mental capabilities or lack experience and knowledge i f they have been !liven supervision on instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made without supervision.

1. Attach the ground spike to the laser­ light: place the nut into the hexago­nal hole in the ground spike holder. Place the round end of the ground spike into the ground spike holder and fasten it with the clamping screw.
2. Position the laserlight a distance of no more than 10 metres from the object onto which the laser beam is to be projected. Anchor the ground spike in the ground (if indoors: in a nower pot).
3. Orient the laserlight towards the object. io do this, you can loosen the clamping screw and tighten it again after you have oriented the laserlig ht.
4. Lay the mains cable in such a way that rt does not present a trip hazard.
5. Plug the cable connector into the socket on the mains adapter that is also supplied. Then twist the cap nut onto the thread of the mains adapter.
6. Only connect the mains adapter to a plug socket that has been properly installed.

Use

1. Before you use the remote control for the first time, pull the insulation strip out of the battery compartment to activate the battery.
2. If the laserlight does not switch on automatically after you have connected it, point the remote control at the front of the laser­light and press the ON button.

CAUTION: Laser radiation can result in blinding and permanent damage to the eyes.

Point the remote control directly at the front of the laser light.  The distance between the remote control and the laserlight should be 15-25 meters.\ When the laser light is lit in a dark environment, the brightness of RED.GREEN and BLUE laser color:Green is brightest than RED  and BLUE,the reason is depend on the characteristic of GREEN  laser diode

FCC Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
  Note: The Grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. such modifications could void the user’s authority to operate the equipment.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>