LEOOUT SX10 Electric Scooter User Manual
- June 1, 2024
- LEOOUT
Table of Contents
LEOOUT SX10 Electric Scooter
Product Introduction
Product Overview
Main Part Introduction
- Front light button
- Horn button
- LCD (with USB port)
- Accelerator
- Speed limit button
- Single/ Dual engine button
Installation Instructions
- Install the front pole, insert the fixed shaft and tighten the screw
- Lower and lock the fastener
- Install the handlebar and tighten the screws
- Install the headlight
- Tighten the screw
- Done
Folding Instructions
- Unlock the fastener
- Lift the fastener
- Fold the pole
- Done
Charge Your Scooter
Safety Instructions
This manual has been created to help you understand the safe use and maintenance of the LEOOUT SX 10 electric scooter.
- Persons without excellent vision, balance, coordination, reflex, muscle and bone strength and good decision-making capabilities should not use this product.
Display Manual
ON/OFF:
Long press the “Power” Button for 3 seconds to start or shut down the scooter.
Auto OFF: After five minutes of using any function, the scooter will be
automatically powered off.
Display content switch:
In power on condition, short press the “Power” Button to switch TRIP/ODONOL on
the LCD.
Note: TRIP is Single mileage, ODO is cumulative mileage, and VOL is battery voltage. Speed Mode Switch: In power on condition, short press the “Mode” Button to switch speed mode.
Settings
- P01: Brightness of backlight, 1 level is the darkest, 3 levels are the brightest; This function has been blocked, the default is the brightest.
- P02: Mileage unit, 0: KM; 1: MILE;
- P03: Voltage level: 36V, 48V, 52, 60V default 52V;
- P04: Dormant time: 0, no dormant; other numbers are dormant time, range: 1-60; unit minutes; default 1
- P06: wheel diameter: unit, inch; precision: 0.1; default 10
- PO7: Speed measuring magnet number: range: 1-100; default 30
- P08: Speed Limit Maximum motor speed; Default 100
- P09: Zero start, non-zero start setting, 0: zero start; 1: non-zero start;
- P10: drive mode setting 0 boost drive 1 electric drive 2 boost drive electric drive coexistence
- P11: Boost sensitivity setting 1-24
- P12: Starting torque: range: 0-5, 0 weakest, 5 strongest;
- P13: booster disk magnet type setting 5 8 12
- P14: Controller current limit value setting Default 12A Range: 1-20A; (controller software support required)
- P15: Motor drive signal percentage setting Default 100 Scooter factory setting: value p2-0 p3-52 p4-1 p5-3 p6-10 p? -30 p8-100 p9-0 p10-2 p11-2 p12-2 p13-5 p14-12 p15-100 p16-0
Introduction of buttons and interfaces
- When it is shut down, long-time pressing to turn on the power. When it is power on, It can change the interface between the ODO, TRIP, and VOL, by pressing for a short time.
- When it is powered on, long-time pressing to turn it off.
- Long-time pressing and – can get into the menu to change the interface, in the setting interface, short-time pressing can change gear. Short press to change the speed status, the gear is switched from O to the highest gear. The default gear is 6 gears, the motor does not run in O gear, and the highest speed is in 5 gear.
- Parameter value modification:
- Enter the parameter setting meeting, adjust the parameter you want to adjust and increase or decrease the parameter value through the and the .
- After confirming that the modification is completed, long press the and the -to exit the parameter setting, and then turn off and restart the machine. Shutdown and reboot means that the modification of parameters is complete.
- The rocker arm adjusts motor speed, toggles from top to bottom, and motor speed increases; let go to return to zero position.
- Gauges with headlight function, long-time pressing to turn on the headlights.
- ERRO 1 : Motor failure
- ERRO 2 : turnbuckle fault
- ERRO 3 : Controller Failure
- ERRO 4: Power failure brake
- ERRO 5 : Undervoltage protection
- ERRO 6 : Communication failure, the meter can not receive the output of the controller
- ERRO 7 : Communication failure, the controller can not receive the output of the meter
Specification
Items
| Specifications
---|---
Brand
| ****
LEO OUT
Model
| ****
SX10
Motor
| Dual 1400W (Peek Power) Motors
Battery
| ****
52V25Ah 21700 Li-ion Battery
Tire
| ****
10-lnch Wide Tires
Controller
| ****
29A Controller * 2
Brake
| ****
Mechanical brake
Top Speed
| ****
65km/h
Max Range
| ****
70km
Climbing Angle
| ****
40°
Max Load
| ****
150KG
NeUGross Weight
| ****
36.5KG
Body Size
| ****
11662120cm
Folding Size
| ****
1166248cm
Package Size
| ****
1222751.5cm
Battery
| ****
V2 Ah 21700 Li-ion Battery
---|---
Tire
| ****
10-lnch Wide Tires
Controller
| ****
2 A Controller * 2
Brake
|
Top Speed
| ****
km/h
Max Range
| ****
0km
Climbing Angle
| ****
40°
Max Load
| ****
150KG
NeUGross Weight
| ****
40KG
Body Size
| ****
12764.5127cm
Folding Size
| ****
12764.549cm
Package Size| 131.52 51.5cm
Maintenance
Cleaning and storage
If you see stains on the scooter’s body, wipe them off with a damp cloth. If
the stains won’t scrub off, put on some toothpaste, and brush them with a
toothbrush, then wipe them off with a damp cloth. If you see scratches on
plastic parts, use sandpaper or other abrasive materials to polish them.
Notes: do not clean the scooter with alcohol, gasoline, kerosene or other corrosive and volatile chemical solvents to prevent dire damage. Do not wash the scooter with a high-pressure water spray. During cleaning, make sure that the scooter is turned off, the charging cable is unplugged, and the rubber flap is closed as water leakage may result in electric shock or other major problems. When the scooter’s not in use, keep it indoors where it is dry and cool. Do not put it outdoors for long time. Excessive sunlight, overheating and overcooling accelerate tyre aging and compromise the scooter and the battery pack’s lifespan.
Battery maintenance
-
Use original battery packs, use of other models or brands may bring about safety issues;
-
Do not touch the contacts. Do not dismantle or puncture the casing. Keep the contacts away from metal objects to prevent short circuits which may result in battery damage or even injuries and deaths;
-
Use the original power adapter to avoid potential damage or fire;
-
Mishandling of used batteries may do tremendous harm to the environment.
To protect the natural environment, please follow local regulations to properly dispose of used batteries. -
After every use, fully charge the battery to prolong its lifespan. Do not place the battery in an environment where the ambient temperature is higher than 50°C or lower than -20°C (e.g., do not leave the scooter or the battery pack in a car under direct sunlight for an extended time). Do not throw the battery pack into fire as it may lead to battery failure, battery overheating, and even another fire. If the scooter is expected to be left idle for more than 30 days, please fully charge the battery and place it in a dry and cool place. Keep in mind to recharge it every 60 days to protect the battery from potential damage which is beyond limited warranty.
-
Always charge before exhausting the battery to prolong the battery’s lifespan. The battery pack performs better at normal temperature and is poor when it is below 0°C. For instance, when it is below -20°C, the riding range is only half or less at normal state. When the temperature rises, the riding range is restored.
Note: Fully charged SX10 Electric Scooter will last for 120-180 days. The built-in intelligent chip will keep a log of its charging and discharging records. The damage caused by prolonged no charge is irreversible and is beyond limited warranty. Once the damage is done, the battery can not be recharged (Non-professionals are forbidden to dismantle the battery pack, as it may cause electric shock, short circuits or even major safety accidents).
Contact Us
If you have any inquiries, please feel free to contact us, and we will reply
within 24 hours.
For more questions, please scan the QR code and ask.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>