ENDON 106997 Amalfi Floor Light User Manual
- June 13, 2024
- ENDON
Table of Contents
ENDON 106997 Amalfi Floor Light
Product Information
The Floor Light is a lighting fixture designed for indoor use. It operates on a 220-240V~ 50Hz power supply and should only be connected to such a source. The lamp must be protected by a 3 amp fuse in the mains plug. The product is not suitable for use in bathrooms.
The lampshade part of the light can be adjusted to an appropriate angle as needed. It is important to note that bulbs with a wattage higher than specified on the label should never be used as this may damage the fitting. The product should not have any items placed on it or be used to hang anything. If the external flexible cable or cord of the luminaire is damaged, it should onlybe replaced by a qualified electrician to avoid electrical hazards.
Waste electrical products should not be disposed of with household waste. Recycling facilities should be used for proper disposal. Local authorities or local stores can provide advice on recycling options.
Product Usage Instructions
Installation:
- Before installation, read through the safety instructions in the user manual.
- If you are unsure about installing the product, consult a qualified electrician.
- Ensure that the product is connected to a 220-240V~ 50Hz power supply.
- Place the product in an indoor location, avoiding use in bathrooms.
- Protect the lamp by using a 3 amp fuse in the mains plug.
Usage:
- To turn on the lamp, plug it into a power source and operate the foot switch.
- Ensure that the bulb being used has a wattage that matches the specifications on the label.
- If the bulb does not light up after installation, follow these steps:
- Check if the foot switch is properly plugged in and turned on.
- Inspect the bulb for any issues or replace it if necessary.
- Check the 3 amp fuse in the mains plug, and if needed, check the relevant fuse in the fuse box.
Care and Maintenance:
- Before replacing the bulb, switch off the product and allow it to cool down as the bulb gets hot during use.
- Use a dry cloth to clean the product. Avoid using liquid or abrasive cleaners.
Assembly:
- Gently pull any excess cable through from under the base and then out through the side of the base.
- Turn the completed assembly anticlockwise approximately 6 times to ensure the cable straightens when fully assembled.
- Screw the assembly in a clockwise direction onto the base.
- Adjust and retighten the nut to ensure the cable is at the back of the product when assembled.
Installation and Safety Instructions Floor Light
Safety Warnings
- These instructions are for your safety. Please read through them thoroughly before use and retain them for future reference. If you are in any doubt about installing this product, consult a qualified electrician.
- This product is only suitable for connection to a 220-240V~ 50Hz supply. It is for indoor use only, and not suitable for a bathroom location.
- This fitting is a Class II, Double Insulated product and does not require an Earth. Live or Neutral must not be connected to Earth.
- Do not attempt to plug in or use this product until it has been fully assembled. Disconnect from mains during assembly or maintenance. this product must be used on a stable, flat surface.
- Under no circumstances must this floor lamp be covered with any material as this could pose a safety hazard. This product is not suitable for persons under 14 years of age.
- This product may contain delicate parts – be careful during handling and maintenance to avoid breakage
- This product may contain delicate parts – be careful during handling and maintenance to avoid breakage
- Never fit bulbs of a higher wattage than those specified on the label as these may damage the fitting
- The lampshade part can be adjusted to an appropriate angle as needed.
- Never put anything on the product or hang anything on any part of this product.
- If the external flexible cable or cord of this luminaire is damaged, it must only be replaced by a qualified electrician to avoid any electrical hazards.
- If the external flexible cable or cord of this luminaire is damaged, it must only be replaced by a qualified electrician to avoid any electrical hazards.
Care and maintenance
For bulb replacement, switch off the product (preferably, isolate it at the distribution board) and allow it to cool down (Caution: bulb gets hot during use). C lea n with a dry cloth only. Do not use liquid or abrasive cleaners on this product.
Troubleshooting
When the bulb does not light after installation:
- Please plug in and operate the foot switch to turn your lamp on.
- Please check the bulb.
- Please check the 3 amp fuse in the plug and ultimately check the relevant fuse in your fuse box.
If you have any doubt about installation/use of this product, consult a qualified electrician
To use this item in Europe, the 3 pin adaptor can be removed by loosening the central screw and removing the adaptor to reveal the 2 pin Europe plug.
Assembly Instructions
Gently pull any excess cable through from under the base and then out through the side of the base. Turn the completed assembly anticlockwise approximately 6 times (Turning the tubes anticlockwise first ensures that the cable will straighten when the tubes are fully assembled). Screw the assembly in a clockwise direction on to the base.
Nut can be adjusted and retightened to ensure the cable is at back of product when assembled
- Scan QR code for multi-language
- UK Manufacturer: BH17 7BY
- EU Manufacturer: Brilliant AG
- Brilliantstrasse 1, D-27442 Gnarrenburg
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>