castle CC-010-0175-00 Hydra X 8S Brushless Marine ESC User Guide
- June 13, 2024
- castle
Table of Contents
QUICK START GUIDE
HYDRA X 8S SPECIFICATIONS
| Application Guidelines | Hobby boats up to 36” |
|---|---|
| Input Voltage Range | Min: 3S LiPo, Max: 8S LiPo, 33.6V |
| BEC Specs | Adjustable from 5V to 8.5V (8 A peak), default 5.5V |
| Sensors | Yes, with optional Sensor Harness (P/N 011-0108-00) |
| Product Use Statement | • Applying voltages higher than 33.6V will cause |
irreparable damage to your controller.
• The Hydra X 8S is a high-performance controller; you must use high-discharge
cells in your high-performance application to ensure vehicle performance (see
Driver’s Ed Guide, “A Word About Batteries”).
• The Hydra X 8S requires the use of connectors designed for 150+ amps
continuous. Ex. Castle 6.5mm polarized or 8mm bullet (Driver’s Ed Guide,
“Connectors and Power Wiring”).
• The Hydra X 8S is not intended for human or animal propulsion.
*Failure to adhere to the Product Use Statement constitutes a violation of the warranty agreement, and will result in non-warranty service fees to repair or replace damaged products.
GETTING STARTED
- Solder a high quality battery connector to the ESC (see Driver’s Ed Guide “Connectors and Power Wiring”).
- Mount the ESC and motor into the vehicle.
- Connect motor to the ESC (see Driver’s Ed Guide, “Motor Wiring”).
- Plug in the RX wire into throttle (#2) and AUX wire into auxiliary (#3/#4).
- Calibrate your ESC to your radio. (See below).
YOU ARE NOW READY TO GO!
THROTTLE CALIBRATION
- Radio on, battery plugged in, ESC off.
- Hold full throttle, turn ESC on (green LED).
- When red LED flashes, go to full reverse.
- When yellow LED flashes, go to neutral.
- Armed and ready!
DRIVER’S ED GUIDE
For more detailed information regarding Getting Started, Throttle Calibration,
using Castle Link, or Transmitter Programming, please read the Driver’s Ed
Guide by visiting: https://www.castlecreations.com/HydraX8sDEG
Or scan this QR code with your smart device to open the link.
RECEIVER CONNECTION
| RX Wire | Plug the RX wire into the throttle (#2) channel on your receiver. |
|---|---|
| AUX Wire | The AUX wire allows you to adjust a setting “onthe-fly” using an |
auxiliary channel on your receiver. The AUX wire function is disabled by default and is programmable via Castle Link. Plug this wire into the auxiliary (#3/#4) channel on your receiver.
TRANSMITTER PROGRAMMING REFERENCE
1.Brake/Reverse Type
• With Reverse
• • Without Reverse
• • • Crawler Reverse| 4. Drag Brake
• Disabled
• • 10%
• • • 20%
• • • • 30%
• • • • • Full On
---|---
2.Voltage Cutoff
• Auto-Lipo
• • None| 5. Motor Type
• Brushless
• • Brushed Reversing
3. Brake Amount
• 25%
• • 50%
• • • 75%
• • • • 100%| 6. Motor Direction
• Normal
• • Reverse
AUDIBLE ALERT REFERENCE
| Start Fail
---|---
| Low Voltage Cutoff
| Over-Current
| Radio Glitch
| Over-Temperature
| Excessive Load
| AUX Wire Radio Glitch
| BEC Over-Temperature
| Data Log Full Warning
ABOUT THE HYDRA X 8S
Motors| Please note that while the Hydra X 8S is capable of handling
incredible amounts of power, your motor must also be up for the task. Always
run your
motor within the manufacturer’s specs. Monitor motor, battery, and controller
temps carefully and never let the motor get above 100° C (212° F). Excessive
heat in the motor can damage the motor, the Hydra X 8S, and the batteries.
---|---
Prop Size| Always start with a smaller prop size. If you wish to change
the prop, motor, or battery, check your temperatures often on the first run.
If the electronics get too hot, decrease the prop pitch or diameter, or reduce
the pack voltage.
Programming| Programming The Hydra X 8S is programmable via transmitter
(see Driver’s Ed Guide) or settings may be programmed via computer with a
Castle Link USB adapter (coupon for free adapter included in package). Program
with a mobile device using a Castle B•Link Bluetooth® Adapter (sold separately
or utilize product discount in lieu of free adapter). See the Drivers’ Ed
Guide for more instructions on transmitter programming and the Castle Link
system (“Tuning with Castle Link” and “Transmitter Programming”).
Data Logging| The Hydra X 8S features data logging. You will be able to
measure and record important power system information during your race, turn-
by-turn. After your run, you can download and analyze this log using Castle
Link. You will be able to inspect many parameters including battery voltage,
motor RPM, ESC temperature and more. Additional information about using the
data logging features can be found in the Driver’s Ed Guide (“Data Logging”).
castlecreations.com
540 North Rogers Road, Olathe, KS 66062
913-390-6939 (ext. #1 Support, #2
Service)
Product Support: castlecreations.com/contact-
support
Service: castlecreations.com/contact-service
Website: castlecreations.com
© 2023 Castle Creations
P/N:095-0468-00
Revised 05/2023
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>