LEITZ IQ Slim Home Office P4 Paper Shredder Instruction Manual
- June 13, 2024
- LEITZ
Table of Contents
LEITZ IQ Slim Home Office P4 Paper Shredder Instruction Manual
Specifications
- Model: IQ Slim Home Office P4 / IQ Slim Office S P4
- Cut level: P-4 (4x32mm)
- Sheet: Capacity 10 sheets (80 gsm)
- Run Time: 3 mins on / 6 mins off
- Bin Size: 23 litres
- Volts: / Hz 220-240V AC 50/60Hz
- Amperage: 1.5A / 1.5A
ATTENTIONS To register and activate your warranty go to
www.leitz.com
For service addresses, go to www.leitz.com
Overview
- a Indicator panel
- b Shredder head with handles
- c Bin viewing window
- d Safety symbols
- e Paper feed slot
- f On/Off switch
Please read and keep these important safety instructions
For a full copy of the operating instructions, hints & tips and troubleshooting guide, please visit www.leitz.com
The following symbol which is found on the product indicates you could be seriously hurt or killed if you open the machine. DO NOT OPEN.
WARNING
Electrical shock hazard.
Do not open. No user serviceable parts inside. Refer servicing to qualified
service personnel.
- Only use the unit for its intended purpose.
- The unit must only be connected to a supply voltage corresponding to the electrical rating shown on the unit.
- Unit should be connected to a socket outlet near the equipment that is easily accessible.
- Do not connect multiple adaptors or use with an extension cable.
- Failure to follow these instructions could result in damage/injury and will invalidate your guarantee.
- Do not attempt to service or repair the unit yourself.
- If recycling, separate paper and credit card shreds.
- Do not use this unit if the cable or plug have been damaged.
- Care should be taken when moving equipment to avoid any unleveled surfaces.
- Please read all the safety information and the instructions. The manufacturer is not liable for cases of material damage or personal injury caused by incorrect handling or non compliance with the safety instructions. In such cases, the warranty will be voided.
- The device is intended for use indoors. Never use outdoors.
- Keep the device away from moisture.
- Be vigilant at all times, and always be careful what you are doing. Do not use electrical equipment if you are lacking in concentration or awareness, or are under the influence of drugs, alcohol or medication. Even a moment of inattentiveness can lead to serious accidents and injuries when using electrical equipment.
- Do not attempt to open, modify or repair the device. Do not drop, puncture, break or expose to high pressure.
- Alterations to the device and technical modifications are not permitted.
- Check the device and cable (and if applicable, the adapter) for any damage before use. If there is any visible damage, a strongodour, or excessive overheating of components, unplug all the components immediately and stop using the device.
- Shredder must be disconnected from power source, if not used for an extended period of time.
- Do not use spray cleaners or spray lubricants as these may present a risk of flash fire.
Warning:
Sharp edges, do NOT touch cutters
Warning:
Moving parts, do NOT touch cutters
Never bypass the safety interlock (strictly forbidden & dangerous, especially when unit is connected to a power source)
Indicator Panel | Icon | Colour |
---|---|---|
Power On BUTTON | White | |
Reserve BUTTON | ||
Shredding in operation INDICATOR | Blue | |
Cooling Down INDICATOR | Red | |
Auto reverse indicator | Red |
Operation
-
Remove shredder from packaging and place shredder head on top of the bin.
-
Connect shredder to an appropriate mains supply. Ensure the on/off switch is in the On position. The blue shredder in operation icon **** will flash every 3 seconds.
-
To commence shredding press and release the button. The flashing icon changes to a solid blue light. You are now able to shred.
-
Insert paper to be shredded into the feed slot ‘e’.
While paper is being shredded the blue shredder in operation icon will remain illuminated.
Note: Make sure the paper to be inserted is neatly stacked.
If the paper thickness is within the shredder’s capacity, the motor will start and your documents will be shredded. The cutters will stop once the shredding process is complete. -
If the paper thickness is greater than the shredder’s capacity the auto reverse icon will flash red **** and the motor will run in reverse.
-
If this happens, remove some of the sheets from the paper stack and re-try. The shredder will automatically start and allow the paper to be shredded.
Warning: Do NOT under any circumstances use any metal objects (scissors,
letter openers etc.) in an attempt to clear the paper entry
Warning symbols
No CDs
Keep loose jewellery clear
No credit cards
Ties and loose clothing hazard
Keep long hair clear
Do not reach into opening
This equipment is not intended for use by children
Manual feed slot capacity
No aerosols
Rare occasions of jamming
Should the paper jam not clear, press and hold the button for 2 seconds, then press and hold the button for 2 seconds. Repeat until the jam has cleared. Please do not alternate between the Reverse and Forward functions quickly as this may damage the motor.
Reverse function
- Should you wish to reverse the shredding direction whilst shredding a document a reverse function has been fitted for your convenience.
- By pressing and holding the reverse button the cutters will change direction allowing the retrieval of the document being shredded.
- The reverse function will only run whilst is being pressed. When the reverse button has been released the shredder will revert to ready mode.
Operation time
When the shredder is used continuously for 6 minutes or more the shredder may
overheat. If this occurs the overheat icon will illuminate red.
When the shredder is ready to be used again the red overheat icon will go out. This will take approx. 60 minutes.
To resume shredding, press the On button and start feeding documents into the feed slot.
Quiet shredding
This shredder has been designed with quiet shredding technology.
This allows you to shred with peace of mind you will not disturb others.
IQ Slim Home Office P4 shredding capability
CAN shred the following:
IQ Slim Home Office P4: 10 sheets
- Stapled paper, 25mm within the corner
- 26/6 and 24/6 or smaller staples
- Small sized paper
Thick paper or card <200gsm
IQ Slim Home Office P4: 10 sheets
- Paperclipped paper, 25mm within the corner
- Capable of shredding small/medium paperclips (max. wire thickness = 0.9 mm)
-
80/100gsm paper
Glossy paper or a sheet covered with print on both sides.
Multiple folded sheets (A3 sheets folded in half).
CANNOT shred the following:
Heavy duty staples. Check the staple leg length is not greater than 6mm.
Bulldog clips
Adhesive labels
Large clips. Check the length of the paperclip is not longer than 32mm.
Bound documents
Magazines or other documents bound by multiple staples or clips.
Plastic sheets, laminated documents, plastic folders.
Credit cards
No aerosols
No oil
CDs & DVDs
Bin full
When the bin is full the shredder head will be pushed up off the bin.
This will stop the shredder from shredding.
Please empty the bin and then position the shredder head back on top of the bin. You can now start shredding.
WARNING
The shredder bin must be fully pushed closed for the machine to operate.
- Empty the shredder bin when it is full otherwise the shredder’s performance will be adversely affected. Operating the shredder with a full shredder bin can result in paper jamming in the cutters, which will increase the machine’s noise level.
- Do not force down shredded paper in the bin using your feet.
Troubleshooting
If the paper shredder will not start, please check the following:
- Is the machine plugged in correctly?
- Is the switch pushed to the **** position?
- Is the machine jammed with paper?
- Has the motor overheated?
Accessories
Only use Rexel accessories:
Oil Sheets (20) – 2101949
Oil Sheets (12) – 2101948
Waste Electrical and Electronic Equipment (WEEE)
Electrical and electronic devices contain materials and substances that can have damaging effects on human health and the environment. This symbol indicates that this device must not be treated as unsorted municipal waste but must be collected separately. Dispose of the device via a collection point for the recycling of waste electrical and electronic equipment within the EU, UK and in other European countries that operate separate collection systems for waste electrical and electronic equipment. By disposing of the device in the proper manner, you help to avoid possible hazards for the environment and public health that could otherwise be caused by improper treatment of waste equipment.
The recycling of materials contributes to the conservation of natural resources.
Guarantee
Operation of this machine is guaranteed for two years within the date of
purchase, subject to normal use. Within the guarantee period, ACCO Brands
Europe will at its own discretion either repair of replace the defective
machine free of charge. Defects due to misuse or use for inappropriate
purposes are not covered under the guarantee.
Proof of date of purchase will be required. Repairs or alterations made by persons not authorised by ACCO Brands Europe will invalidate the guarantee. It is our aim to ensure that our products perform to the specifications stated. This guarantee does not affect the legal rights which consumers have under applicable national legislation governing sale of goods.
This guarantee does not apply to Australian customers – see warranty on page 104.
ACCO Brands Australia Pty Ltd (ABN 16 000 265 047)
This document details the terms and conditions of the warranty against defects provided with this product. Please disregard any other representation contained on this product’s packaging or provided with this product which constitutes or appears to constitute a warranty against defects.
WARRANTY AGAINST DEFECTS
This product comes with ACCO Brands Australia Pty Ltd (ACCO Brands) warranty against defects, the details and conditions of which are set out below.
Subject to the terms and conditions set out in this warranty, ACCO Brands will (at ACCO Brands’ option) repair or replace this product with a new or refurbished product if it contains defects which are a result of faulty manufacturer workmanship or materials.
PERIOD OF WARRANTY
You may claim on this warranty if you notify ACCO Brands within 2 years of the
date of purchase in the manner set out below and if you comply with the other
conditions of this warranty.
WHO CAN CLAIM UNDER THIS WARRANTY?
This warranty applies to and can be exercised by the original purchaser of the
product only. This warranty is not transferrable to any other person or party
under any circumstances.
WHAT THIS WARRANTY DOES NOT COVER
If we reasonably consider that any of the following situations are present,
this warranty does not apply. The situations to which this warranty does not
apply are:
- any cosmetic damage;
- any product where the product’s serial number is no longer present or visible;
- loss or damage caused by factors beyond ACCO Brands’ control including, but not limited to, damage or failure due to power fluctuations, overload, excessive heat or humidity;
- any product which has not been installed and/or maintained according to any care or operating instructions provided with the product;
- any alterations or repairs to the product not authorised in writing or performed by ACCO Brands;
- damage or defects caused to the product due to unusual, abnormal, non-recommended or negligent use of the product;
- any wearable component in any product, including but not limited to blades, slitters, cutting sticks, cutting light bulbs, drill bits, base boards, feed wheels, separators, fuses, cutters and carriers, manual punches and cutting disks, light bulbs and staple inserts; or
- liability based on any service agreement entered into with third parties.
PROCEDURE FOR MAKING A CLAIM
Any claim made under this warranty must be made by sending the faulty product
to ACCO Brands at the address noted below, together with the following
information in writing:
- Your name or company name (if applicable);
- Your address;
- Your telephone number;
- Contact name;
- Machine type, model number and serial number;
- Proof of your purchase of this product, such as your receipt; and
- A detailed description of the defect you believe the product to have.
WHAT WE WILL DO TO HONOUR THIS WARRANTY
Upon delivery to us we will organise for the product to be assessed to
determine if the fault or problem is covered by this warranty. We will advise
you by telephone, email or in writing whether the fault is covered by this
warranty.
STATUTORY GUARANTEES AND YOUR OTHER RIGHTS AND REMEDIES
This warranty against defects is provided in addition to other rights or
remedies you, as a consumer, may have under a law in relation to this product.
Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law.
You are entitled to a replacement or refund for a major failure and for
compensation for any reasonably foreseeable loss or damage.
You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
CONTACTING US
ACCO Brands Australia Pty Ltd (ABN 16 000 265 047)
Australia and New Zealand Distributor
Locked Bag 50
Blacktown BC NSW 2148
For product purchased in Australia call: 1300 278 546
Email: enquiry.nsw@acco.com
For product purchased in New Zealand call: 0800 800 526
Email: enquiry.nz@acco.com
Ref: IQ Slim Home O ffice P4/IQ Slim O ffice S P4 Issue: 1 (01/22)
LEITZ ACCO Brands GmbH & Co KG
Siemensstraße 64
70469 Stuttgart
Germany
www.leitz.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>