ROUSENSMART RS-CTR IOT Machine Controller Instruction Manual
- June 13, 2024
- ROUSENSMART
Table of Contents
ROUSENSMART RS-CTR IOT Machine Controller
Product Information:
Product Name: IOT Machine Controller RS-CTR
Connection Mode: The connection mode is shown in the figure below.
Installation Mode: The installation mode is as shown in the figure below.
Installation Guidelines:
- Attach the controller to the backplane of the cabinet during installation.
- Fix the controller with screws.
- Use a control cabinet with good tightness and convenient subsequent wiring arrangements.
- Place the control cabinet in an open, dry, and non-corrosive liquid place to avoid equipment damage.
Note: Ensure the controller is installed properly according to the provided guidelines to ensure optimal performance and longevity of the equipment.
FCC Compliance:
To maintain compliance with FCC’s RF Exposure guidelines, it is important to install and operate this equipment with a minimum distance of 20cm between the radiator and your body. Please use only the supplied antenna.
Important: If you require further assistance regarding the connection mode, installation, or FCC compliance, please consult the dealer or an experienced radio/TV technician.
This product is a data signal acquisition and control device in the IOT area, which is used for collecting sensor signals in the area and controlled equipment such as lighting, forced-draught fan and water pump in the control area. It has the features of AD Hoc network, self-recovery from network disconnection, self-selection of optimal network path, self-rehabilitation from link failure, and supports hibernation and wake up. The product is made of aluminum alloy material, with waterproof and moisture-proof measures, so that it is suitable for the complex scene with harsh environment or strong interference, such as underground pipe gallery, tunnel, mine, factory, etc. It has the features of AD Hoc network, self-rehabilitation from link failure, so that it has the ability to adapt to various complex environments. It has DI, DO, AI, and RS485 ports, and can adapt to the existing various controlled devices in the market.
Product parameters:
- Frequency range: 2405-2480MHz
- Working voltage: 24 V DC
- Transmitted power: +20dBm
- Receiving sensitivity: -103dBm
- Transmission rate: 250kbps
- Analog input: 4~20mA*2
- Serial interface: RS485*2
- Digital input: DI*10
- Digital output: DO*8
- Antenna gain: 4.12dBi
The connection mode is shown in the figure below:
The installation mode is as shown in the figure below:
During installation, first attach the controller to the backplane of the cabinet, and then fix it with screws. The control cabinet with good tightness and convenient subsequent wiring arrangements should be used. The control cabinet should be placed in an open, dry and non-corrosive liquid place to avoid damaging the equipment.
FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Any changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular
installation. If this equipment does cause harmful interference to radio or
television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with minimum 20cm distance between the radiator and your body: Use only the supplied antenna.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>