niko 353-751321-1 Presence Detector User Manual
- June 13, 2024
- niko
Table of Contents
niko 353-751321-1 Presence Detector
Presence detector P47LR, DALI-2, master, 32-37 m, 360°, SnapFit, for flush mounting, WAGO WINSTA® MIDI 2 m cable with 5-pol. connector
Wiring
230 V – OFF
Dimensions
Installation
App Settings
| | |
---|---|---|---
Factory settings| Switch ON/OFF| 500 lux| 15 min
| |
---|---|---
Specifications
Article number……………………………………………………………………………………… 353-751321-1
Configuration ………………………………………………………………………………………….DALI-2 master
Input voltage………………………………………………………………………………230 Vac ± 10 %, 50 Hz
Maximum power consumption …………………………………………………………………………… 0.5 W
Circuit breaker………………………………………………………………………maximum MCB rating 16 A*
Short circuit behaviour shutdown trigger…………………….. voltage below 12 V,
exceeding 1.3 s
Short circuit behaviour restart period …………………………………………. every 14 s until
success
Detector output………………………………………………………………. DALI Broadcast/DALI Adressable
Maximum voltage on the DALI bus ……………………………………………………………………..15 Vdc
Maximum supply current………………………………………………………………………………… 250 mA
Maximum guaranteed current on DALI bus……………………………………………………….. 100 mA
Maximum startup time DALI ……………………………………………………………………….. < 1200 ms
Maximum PIR detection startup time……………………………………………………………………..70 s
Maximum number of control gear on the DALI bus …………………………………………………… 64
Maximum number of dimmable zones ………………………………………………………………………. 3
Light intensity range ………………………………………………………………………….. 20 – 2000 lux, ∞
Switch-off delay ……………………………………………………………………… pulse, 20 s – 120 min, ∞
Detection angle……………………………………………………………………………………………………360°
Detection range (PIR) …………………………………………………………… ø 37 m from a height of 3 m
Ambient temperature ……………………………………………………………………………… -25 – +40 °C
Mounting method …………………………………………. flush mounting with SnapFit mounting bracket
Mounting height ………………………………………………………………………………………….. 2 – 3.5 m
Colour…………………………………………………………………………………………………white (RAL 9010)
Drill diameter………………………………………………………………………………………………….. 76 mm
Minimum flush mounting depth……………………………………………………………………… 56.9 mm
Dimensions visible (HxWxD) …………………………………………………………. 100 x 100 x 42.2 mm
Dimensions (HxWxD)……………………………………………………………………. 120 x 120 x 99.1 mm
Wire capacity ……………………………………………………………………………………………1.5/2.5 mm²
Protection degree ……………………………………………………………………………………………….. IP20
Impact resistance……………………………………………………………………………………………….. IK04
Modification of settings …………………… app (iOS/Android) and 2-way Bluetooth®
communication
Maximum range Bluetooth® (free field, depending on the device) ………………………….. 50
m
Operating frequency……………………………………………………………………………………….. 2.4 GHz
Maximum radio frequency power…………………………………………………………………….. -2 dBm
Halogen-free …………………………………………………………………………………………………………yes
Marking ……………………………………………………………………………………………………………….. CE
Cable specifications
Cable colour…………………………………………………………………………………………………..black
Length……………………………………………………………………………………………………………..2 m
Wire cross-section……………………………………………………………………………………. 1.5 mm²
Voltage………………………………………………………………………………………………………….400 V
Rated current ………………………………………………………………………………………………….16 A
Halogen-free …………………………………………………………………………………………………….yes
Ambient temperature…………………………………………………………………………….-5 – +40 °C
Type of connector ………………………………………………………………………….male, 5-pole, blue
Detection Area
H
|
A
Walking
|
B
Across
|
C
Towards
|
D
Presence
---|---|---|---|---
2.5 m| ø 32 m| ø 28 m| ø 10 m| ø 8 m
3.0 m| ø 37 m| ø 30 m| ø 8 m| ø 4 m
Measured according to EN/IEC63180
LED behaviour
Green LED continuous on| | Connection OK|
---|---|---|---
Green LED breathing| | Connection OK, overrule ON|
Green LED flashing| | Warming up| Wait
Red LED continuous on| | Error| More info – >
detector tool
Red LED breathing| | Warning
Blue LED flashing| | Walk test active
Troubleshooting
| Problem | Possible cause | Proposed solution |
|---|---|---|
| Load does not turn on | The wiring is not correct | Check the wiring scheme |
| The ambient light is too strong | Check the response value luminosity and raise |
the value if necessary
Load does not turn off| The switch-off delay is too long| Check the switch-off
delay and shorten the delay if necessary
The detector receives false triggers| Check for any objects that may cause
false triggering and remove them from the detection range or lower the
sensitivity
App cannot connect to the detector| Bluetooth® has been disabled on your
mobile device| Enable Bluetooth® on your mobile device
Support & Contact
nv Niko sa
Industriepark West 40
9100 Sint-Niklaas, Belgium
www.niko.eu
+32 3 778 90 80
support@niko.eu
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>