FRIGIDAIRE FFMOTK27LW Built-In Microwave Trim Kit Installation Guide

FRIGIDAIRE FFMOTK27LW Built-In Microwave Trim Kit

Product Information

This product is a Built-In Trim Kit designed for use with Electrolux Microwave Ovens specifying the Built-In Kit FFMOTK27LW/B/S or FFMOTK30LW/B/S. It allows for the installation of microwaves to be built into a cabinet or wall. The kit includes a Front Frame Assembly, an Exhaust Duct, Screw A, and Screw B.

Product Usage Instructions

1. Before beginning the installation, read the instructions completely and carefully.
2. Ensure that the power is switched off at the service panel and lock the service disconnecting means to prevent accidental switching on of power. If the service disconnecting means cannot be locked, securely fasten a warning device to the service panel.
3. Choose a location for your microwave oven if built-in. The Trim Kit can be installed in a cabinet or wall by itself or over an electric wall oven. Ensure that there is a minimum clearance of 3 inches between the wall oven and the microwave oven if building over a wall oven.
4. Refer to Illustration 1 for the proper location of the Front Frame Assembly. If building over a wall oven, follow both the wall oven installation instructions and Electrolux’s Built-in Kit instructions.
5. Ensure that the cabinet or wall cutout dimensions meet the minimum and maximum requirements specified in the manual.
6. Install the Exhaust Duct Assembly by placing it correctly in the opening. The Central Line on the floor should align with the middle of the Exhaust Duct Assembly. See Illustration 3 for reference.
7. Refer to Illustration 2 for the installation of Screw A.
8. Ensure that the electrical outlet location is not in the shaded area as indicated in Illustration 2.

If you have any questions or need further assistance, please refer to the contact information provided in the manual.

BEFORE YOU BEGIN

• IMPORTANT – Save these instructions for local inspector’s use.
• IMPORTANT – Observe all governing codes and coordinates.
• Note to Installer – Be sure to leave these instructions with the Consumer.
• Note to Consumer – Keep these instructions for future reference.
• Skill level – Installation of this appliance requires basic mechanical and electrical skills

Rea d these instructions completely and carefully.

• Proper installation is the responsibility of the installer.
• Product failure due to improper installation is not covered under the Warranty.
• Unplug the microwave oven before attempting installation of this kit.
• Because the kit includes metal parts, caution should be used in handling and installation to avoid the possibility of injury.
• Do not remove permanently affixed labels, warnings, or plates from the product. This may void the warranty.

FOR YOUR SAFETY

WARNING – Before beginning the installation, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

IMPORTANT – PLEASE READ AND FOLLOW

THIS BUILT-IN KIT IS DESIGNED FOR USE ONLY WITH ELECTROLUX MICROWAVE OVENS SPECIFYING BUILT-IN KIT

FFMOTK27LW/B/S OR
FFMOTK30LW/B/S ON THE RATING LABEL ON THE LEFT SIDE WALL OF THE MICROWAVE OVEN CAVITY.

QUESTIONS?
For customers in the United States call:1-1800-944-9044 For customers in Canada call: 1-800-265-8352 (English) 1-800-668-4606 ext.8199 (French)
Visit our Website at: www.frigidaire.com

READ CAREFULLY.
KEEP THESE INSTRUCTIONS.

PARTS INCLUDED IN THE KIT

1. Front Frame Assembly- QTY 1
2. Exhaust Duct – QTY 1
3. Bottom Mounting Rail– QTY 2
4. Screw A – QTY 11
5. Screw B – QTY 4

CHOOSING A LOCATION FOR YOUR MICROWAVE OVEN IF BUILT-IN
Built-In Trim Kit allows for the installation of microwaves listed below to be built into a cabinet or wall by itself or over an electric wall oven*.

Microwave Models

FFMO1611LW, FFMO1611LB, FFMO1611LS
See Illustration 1 for proper location and when building in above a wall oven. Carefully follow both the wall oven installation instructions and Electrolux’s Built-in Kit instructions. If building over a wall oven, be sure the clearance between the wall oven and the microwave oven is a minimum of 3 inches.

*NOTE: Trim Kit and microwave can only be built-in over an electric self- clean or non self-clean single cavity wall oven.

CABINET OR WALL CUTOUT

Cutout Dimensions

Illustration 1

Illustration 2

ELECTRICAL OUTLET LOCATION

Outlet should NOT be in the shaded area as indicated on Illustration 2

NOTE 1
The floor of the opening should be constructed of plywood strong enough to support the weight of the oven and floor load (approximately 100 pounds). The floor should be level for proper operation of the oven. Be sure to check the local building code as it may require that the opening be enclosed with side, ceiling and rear partition. The proper functioning of the oven does not require the enclosure.

Illustration 3

EXHAUST DUCT ASSEMBLY

1. Draw a Central Line on floor. Place the Exhaust Duct in the opening，When the Exhaust Duct Assembly is in the opening correctly, the Center Line is in the middle of the Exhaust Duct Assembly. See Illustration 3.

2. Secure the Exhaust Duct Assembly with the three screws A.
   IMPORTANT: Secure screws in outer hole.

3. units are needed for exhaust duct assembly

Bottom Mounting Rail

1. Turn microwave wave upside down so you are looking at oven bottom. Secure the bottom Mounting Rail on oven with four SCREWS A. See Illustration 4 below.
2. Secure the Exhaust Duct Assembly with the four screws A.–Place the bracket on proper location where hole to hole with the oven, then put the screw inside, and screw them up.

Illustration 4

OVEN INSTALLATION

1. Place the oven adjacent to the wall or cabinet opening. Plug the power cord into the electrical outlet.
2. Carefully guide the assembled oven into the prepared opening. Slide the oven on the Exhaust Duct Assembly. See Illustration 5.
3. Secure the Exhaust Duct Assembly with the four screws A.

Illustration 5

FRAME INSTALLATION

1. Position the FRAME ASSEMBLY to be square with the oven. Carefully place the FRAME ASSEMBLY on the oven. See Illustration 6.
2. Check that it is level and then secure with two SCREWS B. Secure the bottom portion of the FRAME ASSEMBLY with the two remaining SCREWS B. See Illustration 7.

Illustration 6

Illustration 7

Documents / Resources

| FRIGIDAIRE FFMOTK27LW Built-In Microwave Trim Kit [pdf] Installation Guide
FFMOTK27LW, FFMOTK27LB, FFMOTK27LS, FFMOTK30LW, FFMOTK30LB, FFMOTK30LS, FFMOTK27LW Built-In Microwave Trim Kit, Built-In Microwave Trim Kit, Microwave Trim Kit, Trim Kit
---|---

References

• Frigidaire

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>