renkforce RF-DP-200 Corded Telephone Instruction Manual
- June 13, 2024
- renkforce
Table of Contents
Operating instructions
Corded Telephone (White)
Item no. 2619753http://www.conrad.com/downloads
Intended use
This product is a corded landline telephone. You can either place the product
on a desk or mount it on a wall.
The product is intended for indoor use only. Do not use it outdoors. Contact
with moisture must be avoided under all circumstances.
If you use the product for purposes other than those described, the product
may be damaged.
Improper use can result in other hazards.
Using the product for purposes other than those described above may damage the
product.
Improper product use can cause a short circuit, fire, electric shock, other
hazards.
This product complies with statutory, national and European regulations. For
safety and approval purposes, you must not rebuild and/or modify the product.
Read the instructions carefully and store them in a safe place. Always provide
these operating instructions when giving the product to a third party.
All company and product names contained herein are trademarks of their
respective owners.
All rights reserved.
Delivery content
Base station | Telephone line cord for the base station |
---|---|
Handset | RJ11/TAE-F adapter |
Coiled handset cord | Operating instructions |
Latest product information
Download the latest product information at www.conrad.com/downloads or scan the QR code shown. Follow the instructions on the website.
Explanation of symbols
In the operating instructions, an exclamation mark inside a triangle indicates
important instructions.
The symbol warns of dangerous voltage that can lead to personal injury by
electric shock.
Safety instructions
Read the operating instructions carefully and especially observe the safety
information. We assume no liability for any resulting injuries or damage to
property if you fail to observe the safety instructions and information on
proper handling in these operating instructions.
Such cases will invalidate the warranty/guarantee.
5.1 General information
- This product is not a toy. Keep it out of the reach of children and pets.
- Do not leave packaging material lying around carelessly. It may become a dangerous plaything for children.
- Maintenance, modifications and repairs must be carried out only by a skilled technician or a specialist repair centre.
- If you have questions that remain unanswered by these operating instructions, contact our technical support service or other technical personnel.
5.2 Handling
- Please handle the product carefully. Impact, shocks or a fall even from a low height can damage the product.
5.3 Operating environment
- Do not expose the product to any mechanical stress.
- Never expose the product to extreme temperatures, strong vibrations, flammable gases, vapours or solvents.
- Protect the product from high humidity and moisture.
- Protect the product from direct sunlight.
5.4 Operation
- Consult an expert when in doubt about the operation, safety or connection of the device.
- If it is no longer possible to operate the product safely, take it out of operation and protect it from any accidental use. DO NOT attempt to repair the product yourself. Safe operation can no longer be guaranteed if the product:
– is visibly damaged,
– is no longer working properly,
– has been stored for extended periods in poor ambient conditions or
– has been subjected to any serious transport-related stress!
Product overview
1 Suspension for handset (front)
2 Holes for wall mounting
3 Volume setting
4 Line socket (TAE socket for the telephone line cord)
5 Hand Set (socket for the coiled handset cord)| 6 Keypad
7 Mute button
8 Pause button
9 Redial button
10 Flash button
---|---
Installation
You can place your telephone on a flat and stable surface, such as a desk, or
mount it on a wall.
7.1 Installing the telephone on a desk
7.2 Mounting the telephone on a wall
Drill two vertical holes in the wall spaced 80 mm apart. Insert the wall plugs
and tighten the screws (both not included) so that the screw heads protrude a
few millimetres from the wall.
You can now hang the telephone on the screw heads by sliding the base station
down.
When penetrating the surface (e.g. drilling or inserting fasteners), make sure
no cables or pipes are damaged. Inadvertently penetrating electric cables
causes the life-threatening danger of an electric shock! Check for concealed
wires and pipes before drilling or inserting fasteners.
- Pull the hook out of the slot in the base station.
- Rotate the hook 180º.
- Replace the hook.
Operation
8.1 Connecting and setting up the telephone
-
Connect the handset to the “Hand Set” socket (5) on the base station using the supplied coiled cord.
-
Connect the base station to the Line socket (4) and its telephone socket using the supplied telephone line cord:
– You can connect the telephone line cord directly to the RJ11 telephone socket.
– Connect the supplied RJ11/TAE-F adapter to the TAE telephone socket. -
Place the telephone on a level and firm surface.
8.2 Making a call
To make a call, lift the handset to take the line and enter the phone number
using the keypad.
8.3 Answering a call
When there is an incoming call, pick up the handset to answer.
8.4 Ending a call
Put the handset back on the base station.
8.5 Setting the ringer volume
Use the “RING” switch (3) on the back of the telephone to adjust the ringer
volume. Set the switch to the “LO” position for a low ringer volume and the
“HI” position for a high ringer volume.
8.6 Pausing the call number dialling
When dialling a call number, press the “PAUSE” button (8) to insert a pause in
the dialling sequence for 3.6 seconds.
This function is only available for telephone exchanges.
8.7 Redialling the most recently dialled number
Your telephone stores the last number dialled. You can redial the most
recently dialled call number using the “REDIAL” button (9).
8.8 Flash button
Lift the handset and press the Flash button (10). The a and b wires will be
interrupted for 80 ms.
This feature activates certain functions in the telephone system or exchange.
Cleaning and care
Important:
-
Do not use aggressive cleaning agents, rubbing alcohol or other chemical solutions.
They can damage the housing and can cause the product to malfunction. -
Do not immerse the product in water.
Use a dry, lint-free cloth for cleaning. Moisten the cloth if needed.
Disposal
This symbol must appear on any electrical and electronic equipment placed on
the EU market. This symbol indicates that this device should not be disposed
of as unsorted municipal waste at the end of its service life.
Owners of WEEE (Waste from Electrical and Electronic Equipment) shall dispose
of it separately from unsorted municipal waste. Spent batteries and
accumulators, which are not enclosed by the WEEE, as well as lamps that can be
removed from the WEEE in a non-destructive manner, must be removed by end
users from the WEEE in a non-destructive manner before it is handed over to a
collection point.
Distributors of electrical and electronic equipment are legally obliged to
provide free take-back of waste. Conrad provides the following return options
free of charge (more details on our website):
- in our Conrad offices
- at the Conrad collection points
- at the collection points of public waste management authorities or the collection points set up by manufacturers or distributors within the meaning of the ElektroG
End users are responsible for deleting personal data from the WEEE to be
disposed of.
It should be noted that different obligations about the return or recycling of
WEEE may apply in countries outside of Germany.
Technical data
Telephone type ……………………….. corded telephone, analogue
Redial function ………………………… yes
Wall-mountable ……………………….. yes
User-replaceable cord ……………… yes
Operating conditions ………………… 10 to +85 °C, 10 – 90% RH
Storage conditions …………………… 10 to +85 °C, 10 – 90% RH
Dimensions (W x H x D) …………… 55 x 60 x 202 mm
Weight …………………………………… 275 g
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240
Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g.
photocopy, microfilming, or the capture in electronic data processing systems
require the prior written approval by the editor. Reprinting, also in part, is
prohibited.
This publication represent the technical status at the time of printing.
Copyright 2023 by Conrad Electronic SE.
*2619753_V2_0423_02_VTP_m_en
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>