GGM Gastro KAVND613 Cold Display Unit User Manual

GGM Gastro KAVND613 Cold Display Unit

COLD DISPLAY UNIT
The Cold Display Unit is a refrigerator designed for food storage and display. It comes with various features and components to provide optimal performance and convenience.

Package Included

• Refrigerator Bathtub X 6
• Side glass panels x 2
• Plugs
• User guide
• Adjustable feet x 4

Product Usage Instructions

Start-Up

1. Make sure the power switch is set to [O] and plug it in.
2. Turn on the power. The device displays the current temperature inside on the first screen.

Control Section: Setting the Working Temperature
To set the working temperature, use the digital panel thermostat located on the device.

Manual Defrost
To initiate a manual defrost:

• Press and hold the defrost button.
• The Defrost light comes on for 2 seconds to start a manual defrost.

Cleaning the Condenser
Periodic cleaning of the condenser can extend the life of the device. It is recommended to clean the condenser every 3 months.

Troubleshooting
The following sounds can be heard while your refrigerator is operating:

• Humming sound: A sound is heard in the refrigerant pipes during the first operation when the gas decides to circulate completely in the system.
• Vibrating/Airflow or humming sound: Fans/compressor speed regulation auto-adjusts to achieve performance.
• Hissing/Crying sound: Vibration of refrigerant flow, movement of refrigerant circulating lines, or sound made by spare parts placed on the refrigerator.
• Squeaking/Cracking/Dripping sound: It is produced during the melting of ice from the ice maker (evaporator) mold.
• Squeaky/Gurgling/Boiling sound: Water dripping onto the heater during the defrost cycle.
• Hashing sound: Constriction/expansion of the inner walls, especially during the initial cooling, friction occurs.
• Water flowing sound: It can be heard when the water melts during the defrost cycle and the flowing water enters the drain pan.

Before Calling Service
Your refrigerator may be equipped with an automatic fault monitoring system. If your device malfunctions, please check the troubleshooting table in the user manual before calling for service.

Technical Features

• Model: FLT-140, FLT-180
• Voltage: 230V 50Hz
• Power: 170W
• Temperature Range: (dependent on model)
• Capacity: (dependent on model)
• Cooler: R290 100g (FLT-140), R290 120g (FLT-180)
• Dimensions (HxWxD) mm: 1395x400x250 (FLT-140), 1750x400x250 (FLT-180)

Electrical Installation
The plug must be connected to a suitable electrical outlet. It is important to follow these guidelines:

• All the devices must be grounded using a special grounding circuit.
• Have a qualified licensed electrician handle the electrical installation.
• Keep electrical isolation points clear of any obstructions for easy access in case of emergency disconnection.

WEEE Disposal
The WEEE logo on this product or its documentation indicates that the product should not be disposed of as household waste. It should be disposed of in an approved and environmentally safe recycling process. For more information on how to correctly dispose of this product, contact the product supplier or your local waste disposal authority.

DESCRIPTION

Safety Tips

• Emplace it on a flat, stable surface with the balance.
• Installation and, if necessary, repairs should be performed by an authorized service representative/authorized technician. Do not remove any components or service panels from this product.
• Consult Local and National Standards to comply with: Occupational Health and Safety Legislation
• BS EN Code of Practice
• Fire precautions
• IEE Cabling Regulations
• Building Regulations
• DO NOT use a jet/pressure washer to clean the device.
• DO NOT use the device outside.
• DO NOT use this device to store medical supplies.
• DO NOT use electrical appliances (e.g. heaters, ice cream makers, etc.) inside the appliance.
• DO NOT force or consolidate anything heavy on the pedestal, drawers, or doors.
• DO NOT allow it to come into contact with oil or sticky plastic components or the door seal. If contact occurs, clean immediately.
• Bottles with a high alcohol content should be closed and placed vertically in the refrigerator.
• Always carry and store the device in a vertical position and move it by holding the base of the device.
• Always turn off and disconnect the unit’s power supply before cleaning.
• Keep all packaging away from children. Dispose of the packaging in accordance with local authority regulations.
• If the power cord is damaged, it must be replaced by a technician to avoid a hazard.

Promotion

Please take a few moments to read this manual carefully. Correct maintenance and operation of this machine is the best possible performance of your product.

• Package Included
• The following are included:
  • Refrigerator
  • Bathtub X 6 Side glass panels x 2
  • Plugs User guide Adjustable feet x 4

Setup

Note:
If the unit has not been stored or transported in an upright position, allow it to stand upright for approximately 12 hours before operating. If in doubt, be sure to wait.

1. Unpack the device. Make sure all protective plastic films and coatings are thoroughly cleaned from all surfaces.
2. Check all parts
3. Leave a distance of 20 cm (7 inches) between the unit and walls or other objects for ventilation. Increase this distance if the obstacle is a heat source.
4. Nothing heavy should be placed on the upper cambered glass.
5. Plug in and check the front digital panel.

Note:
Before using the device for the first time, clean the shelves and inside with soapy water.

1. Digital panel thermostat
2. On/off power switch
3. Sliding front panel
4. Air suction
5. Side panels
6. Body
7. Camber glass phone

Food Storage
To get the best results from your device, follow these instructions:

• Store foodstuffs only when the appliance has reached the correct operating temperature.
• Make sure that the gastronorm compartments are always full, even if the gastronorms are unused or empty. Empty compartments will greatly reduce the efficiency of the device.
• Do not block the fans inside the device.

Start-Up

1. Make sure the power switch is set to [O] and plug it in
2. Turn on the power. The device displays the current temperature inside on the first screen.

Control Section

Setting the Working Temperature

• SET key: Press for 5 seconds to modify the set point (SP), Press for 10 seconds to go to the programming menu. In the programming menu, go to the level displayed or accept the new value while setting a parameter.
• Up key / : Pressing for 5 seconds starts/stops defrosting. In programming menu, allows you to scroll through the various levels or, during the setting of a parameter, to change the value.
• Down key / : Pressing for 5 seconds activates Standby mode, and pressing for 2 seconds returns the equipment to normal mode. In standby mode, the equipment performs no actions and only the indicator is displayed on the screen. In programming menu, allows you to scroll through the various levels or, during the setting of a parameter, to change the value.

1. Stand-by mode
2. Program Mode
3. Display
4. Relais COOL active
5. Relais RES activé
6. Keyboard

• SET key / : Pressing for 5 seconds activates Standby mode, and pressing for 2 seconds returns the equipment to normal mode. In Standby mode, the equipment performs no actions and only the ****indicator is displayed on the screen. Pressing for 10 seconds goes to the programming menu. Pressing for 5 seconds in the programming menu goes to the level displayed on the screen or, during the setting of a parameter, accepts the new value.
  In the programming menu, a short press allows you to scroll through the various levels or, during the setting of a parameter, to increment the value. When the upper limit is reached, it will start again from the lower limit.

Press and hold the defrost button The Defrost light comes on for 2 seconds to start a manual defrost.

Cleaning, Care and Maintenance

• Turn off and disconnect from the power source before cleaning. Clean the inside of the device as often as possible.
• Do not use abrasive cleaning agents. These can leave harmful residues.
• Clean the door seal with water only.
• Always dry after cleaning.
• Do not allow the water used for cleaning to flow into the evaporation pan from the drain hole.
• Be careful when cleaning the back of the device. Sharp edges can be cut.
• If necessary, a technician should carry out repairs.

Cleaning the Condenser

• Periodic cleaning of the capacitor can extend the life of the device.
• You need maintenance every 3 months.

Troubleshooting

The following sounds can be heard while your refrigerator is operating. These Normal.

• Humming sound: A sound is heard in the refrigerant pipes during the first operation when the gas decides to circulate completely in the system.
• Vibrating/ Airflow or humming sound: Fans/compressor speed regulation auto-adjusts to achieve performance
• Hissing/Crying sound: Vibration of refrigerant flow, movement of refrigerant circulating lines, or sound made by spare parts placed on the refrigerator
• Squeaking / Cracking / Dripping sound: It is produced during the melting of ice from the ice maker (evaporator) mold.
• Squeaky/Gurgling/Boiling sound: Water dripping onto heater during defrost cycle
• Hashing sound: Constriction/expansion of the inner walls, especially during the initial cooling, friction occurs.
• Water flowing sound: It can be heard when the water melts during the defrost cycle and the flowing water enters the drain pan

BEFORE CALLING SERVICE

• Your refrigerator may be equipped with an automatic fault monitoring system to detect and diagnose problems at an early stage.
• If your device malfunctions, please check the table below before calling the Helpline.

Fault Messages

• L5 – Access Code (Password) is necessary.
• Def – Informs that a defrost is running (Only if the parameter is d2 = 2)
• E1 – Prop 1 fault. (Open circuit, pass, NTC: heat > 110 °C or <-55°C
  • PTC: heat > 150 °C or < 58 °C) – ( should be equalized at °F

WARNING:
Snow on the device shows that it is melting. It is not a fault description. It only shows the periodic flow of the device.

Technical Features

Model| Voltage| Power| Temperature Range| Capacity| Cooler| Dimensions ( HxWxD) mm
---|---|---|---|---|---|---
FLT-140| 230V 50Hz| 170W| Between +4°C / +8°C| GN 1/3 Tub:6| R290

100g

| 1395x400x250
FLT-180| 230V 50Hz| 200W| Between +4°C / +8°C| GN 1/3 Tub:8| R290 120g| 1750x400x250

Electrical Installation

The plug must be connected to a suitable electrical outlet. Wired the devices as follows:

• Live wire (brown color) Neutral to the terminal marked L
• Cable (blue color) terminal marked N Grounding
• Terminal with wire (green/yellow color) marked E

All the devices must be grounded using a special grounding circuit. Have a qualified licensed electrician. Electrical isolation points must be kept clear of any obstructions. They should be easily accessible in case of any emergency disconnection.

WARNING:

• The WEEE logo on this product or its documentation indicates that the product should not be disposed of as household waste. To help prevent potential harm to human health and/or the environment, the product should be disposed of in an approved and environmentally safe recycling process. For more information on how to dispose of this product correctly, contact the product supplier or your local waste disposal authority.
• The parts have undergone stringent product testing to comply with regulatory standards and specific actions set by international, independent, and federal authorities.
• The products are approved to carry the following symbols.

All rights reserved. No part of these instructions may be reproduced or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>