Yealink YL43456 WiFi and Bluetooth Module Instruction Manual

Wi-Fi &Bluetooth Module
YL43456

YL43456 WiFi and Bluetooth Module

Parameters:

5.0
Chip| BCM43456
Host interface| Wi-Fi : SDIO, BT :UART
Size| 12mm • 12mm • 2.0mm
Wi-Fi VID/PID| TBD
BT VID/PID| TBD
Weight| TBD
Environment
Voltage| 3.6V
Temperature| -40°C-85°C
Storage temperature| -45°C-135°C
RF character
Frequency| MAN:
2.4 GI-Iz :
2412-2462 MHz 5 GHz:
5150-5350 MHz, 5470-5725 MHz, 5725-5850 MI-Iz BT & BLE:
2402-2480 MHz
Modulation| WLAN: MSS, OFDM,
BT: GFSK, fl/4 DQPSK,8DPSK BLE: GFSK
Max Output power| WLAN:
802.118: 20.71 dBm
802.11a @5GHz: 16.28 dBm
802.11n @5GHz: 15.84 dBm (N20)
802.11n @5GHz: 15.48dBm (N40 )
802.11ac @5GHz: 15.91 dBm (VHT20)
802.11ac @5GHz: 15.52 dBm (VHT40)
802.11ac @5GHz: 14.73 dBm (VHT80 )
BT:
BDR: 7.95 dBm
BLE: 3.53 dBm
Security| ♦WAPI
♦ WEP 64-bit and 128-bit encryption with H/W TKIP processing
♦ WPA/WPA2 Personal (Wi-Fi Protected Access)
♦WMM/WMM-SA/WMM-PS (U-APSD)
♦AES-CCMP hardware implementation as part of 802.11i security standard

Pin Definition

Pin Description

IN
13| WL_wakeup_Host/GPI035| WLAN device wakeup host| OUT
14| SDIO DATA2| SDIO Data Line 2| I/O
15| SDIO DATA3| SDIO Data Line 3| I/O
16| SDIO_CMD| SDIO Command Input| I/O
17| SDIO_CLK| SDIO Clock Input| IN
18| SDIO_DATAO| SDIO Data Une 0| I/O
19| SDIO_DATA1| S010 Data Une 1| I/O
20| GND| GROUND| GND
21| CLK_REQ/GPI011| Clock request output| DO
22| VDDIO| 1.8V-3.3V VDDIO supply for WIAN and BT| VCC
23| NC| Floating Pin, No connect to anything.| Floating
24| LPO| External low-power 32.768KHz clock input.| IN
25| PCM_OUT| PCM synchronous data output, connected to PCM_IN on the host.| OUT
26| PCM_CLK| PCM Clock| I/O
27| PCM_IN| PCM synchronous data input, connected to PCM_OUT on the host.| IN
28| PCM_SYNC| PCM synchronous data SYNC| I/O
29| TDI| Reserve for EJTAG| IN
30| TDO| Reserve for EJTAG| OUT
31| GND| GROUND| GND
32| TCK| Reserve for EJTAG| GND
33| GND| GROUND| GND
A| BT_EN| GPIO pin to on/off the BT function by software. Active high. Reserve pull high 100K resistor and shunt 100pF capacitor to GND on host.| IN
35| NC| Floating Pin, No connect to anything.| Floating
36| GND| GROUND| GND
37| NC| Floating Pin, No connect to anything.| Floating
38| NC| Floating Pin, No connect to anything.| Floating
39| Debug_UART_ThD| TXD for Wi-Fi Uart_debug only, connected to RXD of the host.| OUT
40| DebuLUART_RXD| RXD for Wi-Fi Uart_debug only, connected to TXD of the host.| IN
41| UART_RTS| UART Ready To Send, connected to as on the host.| OUT
42| UART_TXD| UART Transmit Data, connected to RXD on the host.| OUT
43| UART_RXD| UART Receive Data, connected to TXD on the host.| IN
44| UART CTS| UART Clear To Send, connected to RTS on the host.| IN

Enclosure information

Module installation:

The Wi-Fi&Bluetooth wireless module is installed in the lower left corner of the Whole mainboard by the factory operator during the production process.
After assembly, the Wi-Fi&Bluetooth wireless module is built-in by welding in the whole mac hine, which is not removable and will not be used alone, and does not require additional ope ration by users and other personnel.
The procedure and installation position of Wi-Fi&Bluetooth wireless module production and assembly are shown as below:

Wi-Fi&Bluetooth| 1| Fig 1 is the Wi-Fi&Bluetooth ModuleAssembly the Wi- Fi&Bluetooth Module in the lower left corner ofthe whole mainboard, as Fig 2|

---|---|---|---
Module| 1

Host installation:

The host will be assembled by the factory operator during the production process, and the consumer can mount the host either on the conference table, or mount it on the top of TV, on the wall, on the ceiling, onto a TV stand or a tripod with great flexibility according to your needs.
FCC regulatory compliance statement
§15.19 Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
§15.21 Information to user
Warning: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

• Limited module procedures
  This module is a limited module.

• RF exposure considerations
  This Module complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

• Label and compliance information
  Please notice that if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains FCC ID: T2C- YL43456” any similar wording that expresses the same meaning may be used.
  § 15.19 Labelling requirements shall be complied on end user device.
  Labelling rules for special device, please refer to §2.925, § 15.19 (a)(5) and relevant KDB publications. For E-label, please refer to §2.935.

• NII:
  According to FCC Part 15.407 (g), Yealink is responsible for U-NII device to ensure frequency stability in order to keep the transmission within the operating band under all normal operating conditions as specified in the user manual.

• ISED compliance statement
  This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
  (1) This device may not cause interference.
  (2) This device must accept any interference, including interference that may cause undesired operation of the

• ISED Radiation Exposure statement
  This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment.
  This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

• End Device Labelling
  Please notice that if the IC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains IC: 10741A- YL43456” any similar wording that expresses the same meaning may be used.

• 5G Wi-Fi Use Notice
  1. the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
  2. the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall comply with the e.i.r.p. limit; and
  3. the maximum antenna gain permitted for devices in the band 5725-5825 MHz shall comply with the e.i.r.p. limits specified for point-to-point and non point-to-point operation as appropriate.
  4. Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices.

• Antennas information for FCC & IC
  ♦The module itself does not have an antenna. During the test, the host provides a FPC antenna with a maximum gain of 3dBi.
  ♦The module is limited to Yealink installation only
  ♦ Yealink integrators is responsible for ensuring that the end-user has no manual instructions to remove or install module
  ♦For FCC only: The module is limited to installation in mobile or fixed applications, that separate approval is required for all other operating configurations, including portable configurations with respect to Part 2.1093 and different antenna configurations
  ♦ Antenna installation requirements: refer to Pin Definition, while installing the module, the antenna also has been installed in the host;

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>